Suppose that the switch shown in the circuit above has been in position a for a very long time. The emf of the battery is č = 12 V. The resistor has resistance R = 60.0 2 and the inductor is made from a 4.5 cm long, 1.0 cm radius solenoid with 150 turns. What is the current in the circuit 10.0 µs after the switch is moved to position b? L R

Suppose that the switch shown in the circuit above has been in position a for a very long time. The emf of the battery is č = 12 V. The resistor has resistance R = 60.0 2 and the inductor is made from a 4.5 cm long, 1.0 cm radius solenoid with 150 turns. What is the current in the circuit 10.0 µs after the switch is moved to position b? L R

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating of 600 WVDC. The capacitor and resistor are connected to a 480-V, 60-Hz circuit. Is the voltage rating of the capacitor sufficient for this connection?
Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
Which of the following is not a requirement for an electric circuit? a. a source b. a path c. a load d. a signal light
How temperature effect conductivity? Explain with the help of following equation. m e'n7'
the non-inductive resistance of kelvin double bridge are set at 100ON each, the standard resistance is set at 0.10020 and the low resistance 0.0000122 was very low. determine the unknown resistance
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship between the applied circuit voltage and the circuit current? The applied voltage lags the circuit current. The phase shift between the circuit voltage and current changes with time. The applied voltage is in phase with the circuit current. The applied voltage leads the circuit cur Previous Page Next Page Page 2 of 10
Here are the choices: Lorentz law charge Faraday's law Ohm's law Capacitance Resistivity of materials Resistance vs Strain
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?