do= aATAdO AΔd= aATdoBdoΔdΔΤAddoΔΤDdoΔΤAdO EΔdΔΤdoOFO None of the above. The Philippine ten-peso coin (P10) is the secondlargest denomination coin of the Philippine peso.The current version, issued since 2018, has adiameter of d, = 27.0000 mm and a thickness ofhọ = 2.0500 mm. When the coin is subjected to atemperature change of 100 C°, the diameter of thecoin increases by 0.11 percent.Suppose the coefficient oflinear expansion of the coin isunknown, which of thefollowing expressions shouldyou use to compute for it? *

Concept of linear expansion will be used to arrive the final expression

Answered: Suppose the coefficient of linear…

Suppose the coefficient of linear expansion of the coin is unknown, which of the following expressions should you use to compute for it? *

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The answer will be 733.16KN, 1.85 m Show complete solution and draw each step by step.
1:02 M Vo) LTE1 . 94% i 90 1. Show that pure shear gives rise to tensile and compressive stresses across the planes inclined at 45° to the shearing planes, the intensity of the direct stresses being of the same magnitude as shearing stress. 2. Show that volumetric strain in a bar is equal to the sum of strains in three mutually perpendicular directions. 3. Explain the terms: (i) Modulus of elasticity (ii) Modulus of rigidity and (ii) Bulk modulus. 4. Derive the relationship between (i) Modulus of elasticity and modulus of rigidity (ii) Modulus of elasticity and bulk modulus II
a) Fig. 2 shows a rim of a tractor tyre of diameter 60 cm and width 25 cm. After inspection, the tyre was found imbalanced. It seems to the equivalent a 2 kg mass 5 cm from the outside of the tyre and 30cm from the centre of the tyre at 100°, and another one 1 kg mass at 18 cm from outside of the tyre and 10 cm from centre of the tyre at 300° angle. Find masses that should be added to make it balanced at the outside and inside tyre at the rim (30cm from the centre) B 5cm 2kg r3-30cm 18 cm Outside YU с Fig. 2 10cm | by Inside 18cm 300° 100⁰ 10 cm с
1 0 Calculate the total volume of the cylindrical component below (not to scale): L1 D1- D1 = 1.12 cm D2 = 0.71 cm D3 = 1.58 cm L1 = 18.68 cm L2 = 15.36 cm L3=13.77 cm L4 = 9.77 cm Answer: Check L2 L3 L4 D2- What is the volume of the cylindrical component? (State your answer in S.I. units (m³), accurate to 3 significant figures) D3
1.6 What is the density of a metal sample if a15.12-g sample is added into a graduated cylinder increased the liquid level from 35.00 mi to 40.60 raL?
LAL 12 The density of a solid is its mass divided by its volume. If the less is measured as 42.5 ± 0.5 g and the volume as 54 ± 1 cm³, what it be the worst possible error in the calculated density?
The answer to this question in the selected end chapter answers is the following: w_1= 35.2 rad/s w_2 = 42.3 rad/s, w_3= 85.0 rad/s Please show me the solution. Thank you.
1.5A 20 N 2m Find Ox, Oy, Txy in Point A if the diamete=30 MM
The amount of raw material required for a certain machine part is 2.05 cm³. The finished part will have a 1.07 cm³ volume. The processing time of each piece is 50 seconds for copper and 35 seconds for aluminum. The cost of copper is P 30.50 per kg, without a scrap value. The cost of aluminum is P55.00 per kg, with a scrap value of P20.00 per kg. The operator wage is P50.00 per hour and the overhead cost is P60.00 per hour. The copper and aluminum weight 0.0091 and 0.0098 kg per cm³, respectively. Which material will you recommend?
(#1) A metal has a flexural stress of 564 Pa. The width of the metal, w, is measured to be 1 meter, while the load was 10 N. The thickness of the metal is twice its length. Using the formula on the three-point test of materials, compute for the thickness of the metal in centimeters. * 0.0133 1.3298 0.6648 no answer from the choices What is the L in centimeters of the same metal in (#1)? * 0.0133 1.3298 0.6648 no answer from the choices
3) ol Cag. - thing shownin Fig.2.2 the tetal hand loss ChL) from Pant 1 to pant Lis soft, hind the presune atpont 2 0.84)s Hlawnginapipeyender the Gand Port 1 D,z 6in こ 10.70 At Point 2 Dzz 9in Pz z 2 4.00Pt Reference detum
kindly help me with this problem solve as neatly as possible and show completesolution. Round your final answer to 4 decimal places and box / highlight all final answers. all values must include proper units with properconversion if needed in your solution. Please follow the format Given,Required,Solution thank you! 3. Jean Perrin carried out investigations on the sedimentation, in the gravitational field, ofparticles of gamboges, mastic and other paint pigments. Consider particles of density of1.2 g/cm3 with 10 nm radius. Assuming Stoke’s Law applies, estimate the distance (in cm)the particles would sediment in 1 hour, in water at 200C? Density of water = 0.998204g/cm3, viscosity of water = 1.002 cP.