Suppose we assume the diode is ON, what is Vo in volts? Suppose we assume the diode is ON, what is the resistor current I in mA? Suppose we assume the diode is ON, our assumption is correct because the condition ID>=0 will hold as lp will be (in mA) .. Suppose we assume the diode is OFF, this is a wrong assumption because when we solve for Vp with the diode as an open-circuit, the condition V₂<=0 will NOT hold as Vp will be (in volts)...

Suppose we assume the diode is ON, what is Vo in volts? Suppose we assume the diode is ON, what is the resistor current I in mA? Suppose we assume the diode is ON, our assumption is correct because the condition ID>=0 will hold as lp will be (in mA) .. Suppose we assume the diode is OFF, this is a wrong assumption because when we solve for Vp with the diode as an open-circuit, the condition V₂<=0 will NOT hold as Vp will be (in volts)...

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

What is the difference between a diode and rectifier?
What is CEMF?
How do I calculate the dynamic resistance of a zener diode with the following set of values given please? The circuit in figure is the circuit in question I am trying to solve this for please. Vin(DC) = 10V vin(ac) = 0.05sin(wt) Vz(voltage of diode) = 4.5V R1 = 1000 ohms
Determine the state of diode for the circuit shown and find ID, VD. Assume simplified model for the diode. 4k02 2V 1k02. Off, 0.00mA, 0.4V O Off, -0.005mA, 0.0v On, 0.48mA, 0.6v On, 0.55mA, 0.7v Option 5
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to 220V ams 5OHZ İL-DC =05A RL VL-DC =20V
Draw the corresponding output waveform of the double diode partial limiter below using simplified diode model. Indicate all the necessary voltage levels and use Silicon diodes. 20 VP-P 1KQ M D1 9V D2 4.5V VOUT
B. For the circuit shown, determine and sketch the output voltages (Vo). (All diodes are Silicon Diodes). 20 V R - 5 V -20 V
The cut-in voltage for each diode in the circuits shown in Figure Pl.30 is V, = 0.6 V. For each circuit, determine the diode current I, and the voltage Vo (mea- sured with respect to ground potential). Q7 R= 10 k2 Vo oVo Ip R= 10 k2 5 V 5V 5 V 5 V (a) (b) R= 10 k2 Vo 5V E 5 V (c)
A diode circuit is given in the below figure, in which two diodes are connected in series and their saturation currents are Is1 =10-¹6 A and Is2 =10-¹4 A. If the applied source voltage is 1 V, calculate the currents IDI and ID2 and the voltage across each diode VDI and VD2. IDI Ī Vpl + D₂ VD2
Q2:- Find the level of Vo for each circuit shown in the Figure below. Also, determine the status of each diode; if it is forward or reverses biasing. Assume all diodes are silicone with 0.7v drop. +5 V +15 V -10 V (12 Marks) R DI +5 VoK D +5 VoK DI -5 VoH -5 Vo4 D2 D2 D2 +5 VoH D3 +5 Vo4 D3 -10 VoK D4 V. -5 Vo K (a) (b)
Consider diode circuit shown below with Vcc=5V and V₂ = 3V. U₁A HH +V₂ ū The peak inverse voltage on the diode is close to V₁ V. A Vo