swer among the following: 1- For the ramp input, the steady state error of the control system (Type one) is: a) zero b) A/K c) infinite d) none of the them 2- After moving the pick-off point (as shown in the figure). The feedback transfer function will be equal to: RO)- a) H₂G, 0₁ b) H₂/G₁ a)1 b)2 H₂ c) 3 G₂ G(s)H(s)=- H₂ c) H₂+G, 0, 3- For the root locus plot, the number of the asymptotes for the following system are: d) none of them K(s+5) s(s+1) d) 4 C(s)

swer among the following: 1- For the ramp input, the steady state error of the control system (Type one) is: a) zero b) A/K c) infinite d) none of the them 2- After moving the pick-off point (as shown in the figure). The feedback transfer function will be equal to: RO)- a) H₂G, 0₁ b) H₂/G₁ a)1 b)2 H₂ c) 3 G₂ G(s)H(s)=- H₂ c) H₂+G, 0, 3- For the root locus plot, the number of the asymptotes for the following system are: d) none of them K(s+5) s(s+1) d) 4 C(s)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

i. Draw the graph of Ramp signal and also write the equation. i. Define Peak time.
Hybrid vehicle. FIGURE P1 shows the block diagram of a possible cascade control scheme for an HEV driven by a dc motor (Preitl, 2007). The block diagram of the speed control of an HEV taken from FIGURE P1, and rearranged as a unity feedback system is shown in FIGURE P2. Here the system output is C(s) = Kss V(s), the output voltage of the speed sensor/transducer. pC, Av,- Speed K, Gre(s) controller command Torque Amplifier controller output & power voltage amplifier Acro- Motive dynamie Armature Speed |drag torque Angular speed, Ref. circuit Armature torque Vehicle signal R,(s). error U(s) T(s)T,(s) current E,(s) speed, V(s) Gse(s) K, Grc(s) R. tot Friction Feedback speed signal Kss2(s) Feedback torque current signal Kes I(S) T,(s) E,(s) Back emf D=k ks Current sensor sensitivity Kcs Speed sensor sensitivity Kss FIGURE P1 Hybrid Vehicle R (s), E (s) Uc(s) |C(s) + Gsc(s) 0.11 (s + 0.6) SC s (s + 0.5173) + 5 (s + 0.6) (s + 0.01908) URE P2 Block diagram of the speed control of an HEV a.…
below is the representation of a linear control system in the state space.a) estimate the unit digit response by finding the current eigenvalues of this systemb) find the feedback Matrix K= (k1 k2) that must be applied so that the system can be a two - layer root in-2
Feedback is given in the system as (K.fixed number)
A signal generator having a source resistance of 50 2 is set to generate a 1 kHz sinewave. Open circuit terminal voltage is 10 V peak-to-peak. Connecting a capacitor. across the terminals reduces the voltage to 8 V peak-to-peak. The value of this capacitor is -HF. (Round off to 2 decimal places).
below is the representation of a linear control system in the state space.a) examine the controllability and observability of this systemb) estimate the unit digit response by finding the current eigenvalues of this systemC) find the feedback Matrix K= (k1 k2) that must be applied so that the system can be a two - layer root in-2
When the unit step function is applied to the system input given below, the output response is as in figure-b.is happening. K and a seen in the open loop transfer function are constant numbers. Calculate the settling time of the system.
Part 2: Simulink Model for Analysis of closed-loop control System a) The motor transfer function is shown in Figure 2(a) and studies the performance of the system using Simulink if the input is a unit step signal. Choose your group number as a value of K₁: i) R(s) Determine the poles and the zeros of the system and discuss its stability. Also, plot the pole-zero map. ii) obtain the step response of the system, % overshoot, steady state error, peak time Tp and settling time Ts if possible. E(s) K₁ (a) Figure 2 Motor 25 s(s+1) C(s)
An uncompensated system shown in Figure 3(a) has forward transfer function G(s) with a unity feedback. a. Design a phase lead compensator shown in Figure 3(b) cascaded with the uncompensated system shown in Figure 3(a) that will have a 40% or better improvement of the settling time, at least 3 times improvement in percent overshoot. Assume a compensator zero at (given value zc = -10).Show all the complete solution.
Identify the given statement. FM and PM demodulators can actually reduce noise and increase the signal-to-noise ratio during the demodulation process by using limiters. This is known as the capture effect. Select your answer. The statement has no fixed information. The statement is false. The statement is true. The statement is a case-to-case basis.
Hononta (Vj Ais M QUESTION (1) pressure signal from a force transducer is given as under. Analyze it in terms of harmonics, amplitude, circular frequency, cyclic frequency, time period and phase. A. P=15 sin(20m + +12 sin(40t-)+10sin(60t +)+8sin(100zt +")+5sin(140nt -"). +3sin(180) Pa %3D
Mcq Q1) What is the benefit of using two pulse transformers to drive the SCR of a single-phase bidirectional AC voltage controller? * - to isolate the SCRs from the source - to isolate the SCRs from getting short - to isolate the load from the source to control the rms output voltage