Technician A states that coolant in a normal flow cooling system flows from the radiator to the heater core to warm up the passenger compartment quickly. Technician B states that in a reverse flow cooling system, coolant flows to the cylinder heads first, which keeps engine components at a more uniform temperature. Who is correct?

Technician A states that coolant in a normal flow cooling system flows from the radiator to the heater core to warm up the passenger compartment quickly. Technician B states that in a reverse flow cooling system, coolant flows to the cylinder heads first, which keeps engine components at a more uniform temperature. Who is correct?

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter55: Air-conditioning Diagnosis And Service

Section: Chapter Questions

Problem 8ASRQ: While discussing an inoperative blend air door: Technician A says that to check the proper...

See similar textbooks

Similar questions

A vehicle is having its water pump replaced. When the water pump is removed, severe corrosion is found on the water pump impeller, and inside the engine. Technician A states that the radiator cap may be overpressurizing the system. Technician B states that the vehicle may have been run with 100% water in the cooling system for some time. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B
In a reverse flow cooling system, which major component is engine coolant directed to in the engine after leaving the radiator? Select one: a. The thermostat b. The engine block c. The cylinder head d. The throttle body
 Discuss the difference between an air cooled vehicle engine and a liquid cooled engine Discuss the reason to use “Engine Coolants” in engine cooling system. Explain vividly about the functions of Thermostat valve and pressure cap. Discuss the main functions of the lubricating system of an engine Discuss the types of lubricating systems available. Discuss about the Lubricant Classification Discuss how to check lubricant quality of an automobile.
A vehicle comes in with no coolant and a core plug popped out of the engine block. Technician A states that the water pump is likely to be overpressurizing the system. Technician B states that the coolant may not have a low enough freezing point. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A andB d. Neither Technician A nor B
--------Q.1// A conference room is to be air conditioned for comfort conditions of (25oC) DBT and (50% RH). The outdoor air conditions are (35oC DBT) and (28oC WBT). The sensible and latent heat are (43200 kJ/hr) and (36000 kJ/hr) respectively. The return air from the conference room is mixed with outdoor air before entering the cooling coil as shown in the Figure below. In addition, the return air from the (conference room) is mixed with cooling air (after cooling coil) see Figure below, where cooling coil by bass factor (BPF = 0.1) and (ADP =10oC). Theair is reheated to (21oC DBT) before supplying to room.Note: point 6 not equal to point 1.Determine:1 – Conditions at point 3 (DBT3, WBT3, RH3, h3).2 – Conditions at point 4 (DBT4, WBT4, RH4, h4).3 – Conditions at point 5 (DBT5, WBT5, RH5, h5).4 – Conditions at point 6 (WBT6, RH6, h6).5 – The total quantity of air supplied to conference room (kg/sec). 6 – Capacity of reheated coil (kJ/kg).7 – Sensible heat factor SHF.8 – Capacity of…
Select the type of coolant which is very toxic. O a. Mix of Long-Life ethylene glycol and Propylene glycol Ob. Ethylene glycol O c. Propylene glycol O d. Long-Life ethylene glycol
What is the advantage of using an injector-type mixing chamber?
While discussing an inoperative blend air door: Technician A says that to check the proper functioning of the ductwork, move the temperature control lever to see if any change at the doors occurs. If it does not, shut off the air conditioner and turn on the heater. Move the temperature control arm again to see if any change occurs. If not, check the cable and the flap door connected to the temperature control lever. Technician B says that in some cases you can reach under the dash to reconnect the cable or free a stuck flap. Who is right? Technician A only Technician B only Both A and B Neither A nor B
When the car engine is cold, the main cooling cycle is blocked to allow good oil filtration. O increase the engine temperature up O to the optimum engine temperature. easier to be derived. O be better for transmission system. O replace radiator cap. O
What should be done to prevent excessive deposits and buildup within the cooling system? Select one: a. Replace the coolant filter often b. Flush or replace coolant every year c. Use cold tap water when mixing antifreeze and water d. Use distilled water when mixing antifreeze and water
rainsient Cooling -Many years ago, the engineering building air compressor dryer failed and visible water got in the air for transient Cooling. Why couldnot/ shouldnot the experiement be ran?
What advantage might the commercially packaged coolant material have over ice other thanit produces less mess?