The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable must not exceed 19C MPa and that the elongation of the cable must not exceed 5 mm, find the maximum load P that can be applied as shown. -В 2.5 m 3.5 m P A C 4.0 m H The maximum load P that can be applied is KN.

The 4-mm-diameter cable BC is made of a steel with E= 200 GPa. Knowing that the maximum stress in the cable must not exceed 19C MPa and that the elongation of the cable must not exceed 5 mm, find the maximum load P that can be applied as shown. -В 2.5 m 3.5 m P A C 4.0 m H The maximum load P that can be applied is KN.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The tension of cable AC is 110 N. Determine the mass of the crate at point E. g=9.81 m/s² 3m E -3m 6m B 2m y
Bar ABC is supported by two cables and a h inge. Compute the new temperature of alumi num cable if the tensile stress of the steel ca ble is 30 MPa. The current temperature of th e system is 21 degrees Celsius. Assume tha t the new temperature will only affect the alu minum cable. Steel L = 0.9 m A = 300 mm² E = 200 x 10' N/m² a = 11.7 μm/(m °C) B 0.6 m Aluminum L = 1.2 m A = 1200 mm² E = 70 x 10' N/m² a = 23 μm/(m-°C) 1.2 m C
E F G m Determine the deflection in each point of (A,B,C and D) for the 2 m steel system shown in Figure (2) if the cross sectional area of each cable has 50 2 mm. Modulus of elasticity of the steel as H D |-0.2- 0.8m 0.4 m 200 GPa. Beams AB and DC are rigid. A B 0.6- -0.2-1 m m Figure 2 10 kN
The bracket BCD is hinged at € and attached to a control cable | ! at B. For the loading shown, determine (a) the tension in the cable, (b) the reaction at C. a=0. 18m 20N 20N 8 c o I_.l_nm—l—um—-l 02¢m
*2-8 Part of a control linkage for an airplane consists of a rigid member CBD and a flexible cable AB. If a force is applied to the end D of the member and causes it to rotate by 0.3°, determine the normal strain in the cable. Originally the cable is unstretched. 2-9 Part of a control linkage for an airplane consists of a rigid member CBD and a flexible cable AB. If a force is applied to the end D of the member and causes a normal strain in the cable of 0.0035 mm/mm, determine the dis- placement of point D. Originally the cable is unstretched. Fo A 400 mm- D R 300 mm 300 mm P
6. A rigid bar ABCD is pinned at end A and supported by two cables at points B and C (see figure). The cable at B has nominal diameter de =25 mm and the cable at C has nominal diameter dc = 30 mm. A load P acts at end D of the bar. What is the allowable load P if the -dg B - 26 – 2b temperature rises by 90°C and each cable is required to have a factor of safety of at least 5 against its ultimate load? (Note: The cables have effective modulus of elasticity E = 150 GPa and coefficient of thermal expansion a = 12 x 10-6/°C. Other properties of the cables can be found in Table 2-1) P TABLE 2-1 PROPERTIES OF STEEL CABLES* Nominal diameter Effective Approximate weight Ultimate load area (mm) (N/m) (mm²) (kN) 12 6.1 76.7 102 13.9 231 406 20 173 25 24.4 304 32 38.5 481 641 38 55.9 697 930 44 76.4 948 1260 50 99.8 1230 1650
Compute the safest minimum diameter of th e cables if the allowable axial stress of the c able is limited to 60 MPa. All cables have th e same diameter size. B 40" A 50 KN 80" 30° 50° 50 KN E
Two cables BG and BH are attached to frame ACD as shown below. y (G) (A) |G Н (F) (B) D (E) (C) В (D) C P Knowing that the tension in cable BG is 307 N, and dimensions of each section are (A) 1.8 m, (B) 2.1 m, (C) 1.8 m, (D) 1.2 m, (E) 1.2 m, (F) 2.25 m, and (G) 0.16 m. Draw a free-body diagram. Determine the components of the force exerted by cable BG on the frame at B.
H.W.1 8) A shaft of diameter (d 5-mm) is to be pulled through a (4.5)-cm-diameter glycerin-filled sleeve as shown in Figure. The glycerin to be used has a dynamic viscosity of 1.5 Pa.s, and the cable is pulled by 60-N tensile force. If the cable is to be pulled at a velocity of 0.02 m/s and the velocity profile equation though glycerin is (u = 0.6y + 20y2), what is the length of the sleeve that can be used to provide this velocity? Assume that the cable can be kept at the center of the sleeve. Sleeve Shaft
Determine the tension of each given cable below. Required: • Tension at cable AB • Tension at cable BC Tension at cable CD A_ YAO Sm 3m
The crate has an unknown weight W and is held by cable AB, AC, and AD. Each cable can hold a max of 450 pounds. There are the following coordinates: A(0,0,0) B(-2,1,2) C(-2,-2,1) D(3,0,0). Part A) Find the max weight W that the system can hold without breaking any cables Part B) Use the weight from part A to find the tension in the cables draw all FBDs please
5 ft А AST d B B dc. GON C dp D bede -5 @ 6 ft-30 ft- E F An oil pipeline is supported at 6-ft intervals by vertical hab=ngers attached to the cable shown. Due to the combined weight of the pipe and its contents the tension in each hanger is 400 lb. Knowing that d. 12 ft., determine (a) the maximum tension in the cable, (b) the distance do.