The 65 kg man at right is trapped inside a section of large pipe. If that's not bad enough, the pipe begins to roll, from rest, down a 35 m long, 180 incline! The pipe has a mass of 180 kg and a diameter of 1.2 m. (Assume the man's presence inside the pipe has a negligible effect on the pipe's rotational inertia.) The coefficient of friction between the pipe and the ground is (0.5, 0.4).

The 65 kg man at right is trapped inside a section of large pipe. If that's not bad enough, the pipe begins to roll, from rest, down a 35 m long, 180 incline! The pipe has a mass of 180 kg and a diameter of 1.2 m. (Assume the man's presence inside the pipe has a negligible effect on the pipe's rotational inertia.) The coefficient of friction between the pipe and the ground is (0.5, 0.4).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A crate of 68 kg simply stands on the moving cart with constant acceleration a. The height from the center of gravity to the cart, L, is 1.5 m, and the angle 0= 13°. What is the maximum acceleration a (in m/s²) the cart can have without tipping over on the cart? The coefficient of static friction between the crate and the cart is ls = 0.49. Please pay attention: the numbers may change since they are randomized. Your answer must include 3 places after the decimal point. Take g = 9.81 m/s². 0.5 m |0.5 m • G a Your Answer: Answer
The disk with a mass of 0.4 kg and a radius of 2 cm (I = 1 / 2mr ^ 2) slows down as it rolls on a flat surface. While the motion of the disc is the result of the moment of inertia, the friction coefficient is 0.1. Calculate the torque responsible for the deceleration of the disc
A heavy cabinet with a mass of 135kg is transported on the truck platform. Assume that the friction between the cabinet and the platform is so great that the cabinet cannot slip, but can instead tip over. The dimensions shown in the cabinet figure are hG = 1.8m, xG = 1.0m and b = 3.4m. How high can the maximum acceleration of the truck to the right be without the cabinet tipping over? What is the angular acceleration of the cabinet in the situation under consideration
A small object A is held against the vertical side of the rotating cylinderical container of raidus r due to entrifugal action the coefficient of astatic friction between the object and the container is , determine the expression for the maximum rotational rate co of the container which will keep the object from slipping out the vertical side. Fanpas (Fry: Mos FMS.N Fn-man +N=mrw +N=mYw² {fy.g +4₁ (norw')= ndg
weighs 60 N on Earth. (3). A system consists of a pulley (vertical wheel) that is only allowed to rotate (spin). A cord is passed over the pulley and at each end there is a mass attached to the end of the cord. The mass attached on the left is m, =0.6 kg and at the right the mass is m2 = 0.8 kg. a) Calculate both the Tension in the cord and the acceleration of the system. b) What are the accelerations of both masses, if you were to cut the cord? Neglect the friction between cord and wheel,
Need help in 15 minutes. ASAP. A 75-kg block is attached to a cable. The cable is then attached to a rotating assembly with a mass moment of inertia of 18 kg-m^2. The bearing friction applied at the rotating assembly equivalent to a couple of 45 N-m CCW. The block's downward speed is initially at 2 m/s. What is the total work done by the system after the rotating assembly has rotated 1.5 radians CW? What is the speed of the 75-kg block after the rotating assembly rotated 1.5 rad CW?
Question 3 A cylinder rolls freely down at 2°. What will be its speed after rolling 10 m from rest down the incline? What is the total kinetic energy? The mass of the cylinder is 30 kg.
A 10000N weight is to be lowered by a vertical cylinder as shown in Figure . The cylinder hasa 75−mm−diameter piston and a 50−mm− diameter rod. The weight is to decelerate from100m/min to stop in 0.5s. Determine the required pressure in the rod end of the cylinderduring the deceleration motion.
An engineer is designinga conveyor system for loading haybales into a wagon (Fig.).Each bale is 0.25 m wide, 0.50 mhigh, and 0.80 m long (the dimensionperpendicular to the plane ofthe figure), with mass 30.0 kg. Thecenter of gravity of each bale is atits geometrical center. The coefficientof static friction between abale and the conveyor belt is 0.60, and the belt moves with constantspeed. (a) The angle b of the conveyor is slowly increased. At somecritical angle a bale will tip (if it doesn’t slip first), and at some differentcritical angle it will slip (if it doesn’t tip first). Find the twocritical angles and determine which happens at the smaller angle. (b)Would the outcome of part (a) be different if the coefficient of frictionwere 0.40?
The two ramps pictured here each have a region of length L with kinetic friction coefficient uk and are otherwise frictionless. Identical masses m start at identical heights up the ramps, with the same initial velocity down the ramp. How do their final speeds compare when they reach the far right-hand side? (The answer requested here is qualitative and does not require detailed calculation). L m m Vi #0 Vi O Mass is moving faster in #1 The masses are moving at the same speed. Mass is moving faster in #2 O There is not enough information to decide. L Mk#0 1 2 m m Vf,1 V₁,2
If there is n friction in the system, the Lagrange's equation will be based only on kinetic energy and protentional energy only. Select one: O True O False III O
- H1. A wooden block of mass m is pushed over a floor in a straight line in the x direction with a constant velocity vo > 0. At time t = 0, when the block is at position x = 0, it is no longer pushed and the block experiences only a constant sliding friction force F in the negative x-direction until it comes to rest. (i) Write down the equation of motion of the block for t > 0. Calculate the time, t, at which the block comes to a stop and also find the distance, d, travelled by the block from the time when the pushing is stopped to the time when it comes to rest. (ii) Calculate the work done by the friction force from x = 0 to x = d, and then show that it is equal to the change in the kinetic energy of the block.