The American Steel Flange Standard specifies that 8 bolts are to be used on flanges for a 4-in pipe where the steam flows at pressure of 1,500psi. It is also specified that in calculating the bolt load, the outside diameter of the gasket, which is 6.1875in should be used. Determine: (a) diameter of coarse thread bolts if they are well-tightened & made of ASTM 354 (Sy = 120,000psi); (b) the approximate torque to tighten the nuts if the initial stress is 90% of the yield stress.

The American Steel Flange Standard specifies that 8 bolts are to be used on flanges for a 4-in pipe where the steam flows at pressure of 1,500psi. It is also specified that in calculating the bolt load, the outside diameter of the gasket, which is 6.1875in should be used. Determine: (a) diameter of coarse thread bolts if they are well-tightened & made of ASTM 354 (Sy = 120,000psi); (b) the approximate torque to tighten the nuts if the initial stress is 90% of the yield stress.

Name: The American Steel Flange Standard specifies that 8 bolts are to be u
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The American Steel Flange Standard specifies that 8 bolts are to be used on flanges for a 4-in pipe wherethe steam flows at pressure of 1,500psi. It is also specified that in calculating the bolt load, the outsidediameter of the gasket, which is 6.1

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A steel tubing has a 1.5-in outside diameter and a 1.210-in inside diameter. It is made of AISI 1020 annealed steel having a tensile strength of 57,000 psi. What would be the safe working pressure for this tube assuming a factor of safety of 8?
The cylinder of a stationary engine is 4.75 inches diameter and is held to the crankcase by ½ inches nickel steel bolts with American course threads. The maximum gas pressure in the cylinder is 500 psi. Determine the number of bolts required.
1) A set of pipes are available with 50-mm inner-diameter and varying outer-diameters from 51 mm to 53 mm in 0.2 mm increments. A pipe from this set will be used connected to a motor to transmit a power of 110 kW when the pipe is turning at 6000/z rpm without exceeding an allowable stress of 12 MPa, What is the outer diameter of the lightest usable pipe for this cause?
Pressure vessel having 20in diameter is under a repeated load with a maximum pressure of 350psi per cycle. The vessel is made of AISIC1095. Determine its thickness.
The A-36 steel pipe in (Eigure 1) has a 6061-T6 aluminum core. It is subjected to a tensile force of 200 kN. The pipe has an outer diameter of 99 mm and an inner diameter of 89 mm. For A-36 steel, E-200 GPa and for 6061-T6 aluminum. Et 68.9 GPa Figure 200 KN ▼ Part B Ost 400 mm m НА 1 of 1) Value 200 kN Part A Determine the average normal stress in the aluminum due to this loading Express your answer to three significant figures and include appropriate units. HA dal 25.159 Determine the average normal stress in the steel due to this loading. Express your answer to three significant figures and include appropriate units. Submit Previous Answers Request Answer → 1924 Units MPa X Incorrect: Try Again; 5 attempts remaining 2 2 Revien
A Ansle erson E leg the radius of the cylinder. and Fig. 10.19 Problems 10.3 and 10.4 The Anstwer: r = 0.26 m pove.
E AA 2.2 Description An aluminium manifold (shown in Figure 1), is used to convey low pressure air from a supply source to an electronic device. The manifold is manufactured from a square block of aluminium, which is machined using a CNC milling machine. During the manufacturing process of the manifold, two machining setups are required (need to be machined from two sides), resulting in additional set up and machining time required for the manufacturing of the manifold. 96,00 78,00 18,00 20,00 07.00 1.60 Ø18,00 Ø14,00 10,00 SECTION A-A Figure 1: Draft views of the aluminium ma II 00'06 INN 00'S 00'96
the shaft and Bols bolts. [Ans. 300 mm; 56 mm] 11. Design a bushed-pin type flexible coupling for connecting a motor shaft to a pump shaft for the following service conditions: Power to be transmitted = 40 kW; speed of the motor shaft= 1000 r.p.m. ; diameter of the motor shaft = 50 mm ; diameter of the pump shaft = 45 mm. The bearing pressure in the rubber bush and allowable stress in the pins are to be limited to 0.45 N/mm2 and 25 MPa respectively. [Ans. d, = 20 mm; n 6; d, = 40 mm; 1 152 mm] :1.1
Question 4 Squared & ground end A multi disc clutch, as illustrated below, is used to connect a four-cylinder internal combustion engine to a roll mill. The lining material is made of cast iron (Permissible pressure 1.725 MN/m) and friction coefficient of 0.06 running in oil. If the outer diameter of the plates is limited to 200mm and the inner diameter to 100mm, compare the maximum amount of power that can be transferred at 2500 rpm by using the a) principle of uniform pressure and b) uniform rate of wear. (16)
FLUID MACHINERY A 200-mm x 150-mm x 250-mm direct-acting duplex pump delivers water at a temperature of 150oC. The piston rod diameter is 40 mm and the slip is 10%. The pump operates against a pressure of 1500 kPa. Determine a. the theoretical capacity of the pump Answer : __________________ m3/minb. the actual capacity of the pump Answer : __________________ m3/min
find the tensile of the bolt with diameter 38mm,80kN
Asap