The assembly consists of two posts AD and CF made of steel and having cross- sectional area of 1000 mm², and an aluminium post BE having a cross-sectional area of 1500 mm². If a central load P is applied to the rigid member ABC, determine the normal stress in each post. Take elastic modulus of steel and aluminium as 200 GPa and 70 GPa, respectively. PkN P [kN] -0.5 m Last digit of Student ID 0, 1, 2, 3, 4 5,6,7,8,9 500 700 e.g. SID=21051234 A D B -0.5 m C 0.4 m Last digit

The assembly consists of two posts AD and CF made of steel and having cross- sectional area of 1000 mm², and an aluminium post BE having a cross-sectional area of 1500 mm². If a central load P is applied to the rigid member ABC, determine the normal stress in each post. Take elastic modulus of steel and aluminium as 200 GPa and 70 GPa, respectively. PkN P [kN] -0.5 m Last digit of Student ID 0, 1, 2, 3, 4 5,6,7,8,9 500 700 e.g. SID=21051234 A D B -0.5 m C 0.4 m Last digit

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPA, f, = 280MPA and the net tensile strain is greater than 0.005, then the maximum steel ratio equals. . (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
02. The member consists of the steel rod AB that is screwed into the end of the bronze rod BC. Find the largest value of P that meets the following design criteria: (i) the overall length of the member is not to change by more than 3 mm; and (ii) the stresses are not to exceed 140 MPa in steel and 120 MPa in bronze. The moduli of elasticity are 200 GPa for steel and 80 GPa for bronze. Steel A = 480 mm² 1.0 m SUMMARY OF ANSWERS P kN |B 3P Bronze 2 m A= 650 mm? |c 2P
Knowing that the average normal stress in member EF of the Pratt bridge truss shown must not exceed 8.99 ksi for the given loading, determine the cross-sectional area (in sq. in) of this member that will yield the most economical and safe design if h = 11.7 ft and P = 92.21 kips. Round off the answer to five decimal places. 010.png В D F h H C E G -on-- 9 ft→9 ft→9 ft→-9 ft- P P
The horizontal bar ABC is supported by a pin at A and two rods with identical cross- sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 80 kN is applied. Use Est = 200 GPa and Eal = 70 GPa. %3D Steel Aluminum A B T2 m- 1.5 m- Im
The solid cylinders AB and BC are bonded together at B and are attached to fixed supports at A and C. Knowing that the modulus of rigidity is 3.7E6 psi for aluminum and 5.6E6 psi for brass, determine the maximum shearing stress in cylinder AB And cylinder BC in ksi. 1 Aluminum T= 19.6 kip-in. Brass A - 1.4 in. B <-2.1 in. C 10 in. 15 in.
The cross section of the beam in Figure reinforced in negative by 4#25 and transverse stirrups No.10 @ 150 mm along the beam. The longitudinal reinforcement bars are epoxy coated. Determine the required development length for the bars. If, f.'= 20 MPa and f,=400 MPa. 75 mm 4 # 25 550 mm + 450 mm -
Q3. Two steel plates (A572, Fb = 50ksi) are welded together to form an inverted T-beam. Determine the maximum bending stress developed. ( %3D | 10 Marks) 10k 15 k 6ft 5 ft 10 ft 5 ft A B 8ft 1ft
Fill in the blanks: The steel rod is stress-free before the axial loads P₁ =169 kN and P2 = 88 kN are applied to the rod. Assuming that the walls are rigid, calculate the axial force in each segment after the loads are applied. Use E-200 GPa. A = 2000 mm² A = 900 mm² A = 1200 mm² P P₂ B C D +250 -350 mm 500 mm A -250 mm- ANSWER: KN, PBC = PCD = KN KN, PAB = (express it in whole number)
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
Determine the normal stress (in Mpa) in member AB of the truss shown if it is made up of a 14-mm-square bar of alloy and the load P is 21.53 kN. Express your answer in two decimal places.
The following steel circular bar (Es = 200 GPa) is divided into two segments. Segment 1 is tubular and segment 2 is solid. Determine the distance "x" so that the bar does not exceed a total deformation of 2.5 mm. The load P is equal to 25 kN, the diameter d is equal to 30 mm, and the length L is equal to 10 m.