The bracket is held to the wall using three A-36 steel bolts at B, C, and D. Each bolt has a diameter of 0.8 in. and an unstretched length of 2 in. -2 in. 2 in. 1 in. 0.5 in. ▾ Part A If a force of P=600 lb is placed on the bracket as shown, determine how far, s, the top bracket at bolt D moves away from the wall. For the calculation, assume that the bolts carry no shear, rather, the vertical force of 600 lb is supported by the toe at A. Also, assume that the wall and bracket are rigid. A greatly exaggerated deformation of the bolts is shown in the figure. Express your answer to three significant figures and include appropriate units. Value Units ?

The bracket is held to the wall using three A-36 steel bolts at B, C, and D. Each bolt has a diameter of 0.8 in. and an unstretched length of 2 in. -2 in. 2 in. 1 in. 0.5 in. ▾ Part A If a force of P=600 lb is placed on the bracket as shown, determine how far, s, the top bracket at bolt D moves away from the wall. For the calculation, assume that the bolts carry no shear, rather, the vertical force of 600 lb is supported by the toe at A. Also, assume that the wall and bracket are rigid. A greatly exaggerated deformation of the bolts is shown in the figure. Express your answer to three significant figures and include appropriate units. Value Units ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

6. Member BC in the truss below is a 300 mm wide, 10 mm thick steel plate attached to two other 12 mm plates at Joint C by three 24mmp A490N bolts. The plate is A36. Determine the safe load Pu using LRFD that the truss can resist according to the capacity of the connection. 15 15 с 1.5 3P. + D 1.5 80 mm 70 mm 70 mm 80 mm Fac 7. Repeat Problem 6 using 30mm A325-N bolts and A-50 steel. Use ASD. 50 mm Fac
the connection consists of a plate connected to another plate by five 25-mm diameter rivets. it carries a load P = 80 kN. Determine the shear stress on the bolt due to the effect of force alone.
a. Draw the FBD b. Determine the value of P c. Determine the bearing reaction at A. D P. RA E 60° 25" C Az 14" 210 lbs -- - 20
7. The bracket shown is welded on one side of a steel column with 800mm of 6mm fillet weld. Determine the maximum shear stress on the weld. If the allowable stress si 400 MPa what is the allowable load that the connection can carry? 44 kN 300 mm F.W. ON NEAR SIDE F.W. ON FAR SIDE F.W. ON FAR SIDE F.W. ON NEAR SIDE 200 mm 200 mm
The single shear connection consists of six 26-mm-diameter bolts. If the ultimage strength of the bolts is 720 MPa, determine the factor of safety for the connection at an applied load of P= 570 kN. P=570 kN
4 Determine the design angle 8 for connecting mem- ber A to the plate if the resultant force is to be directed vertically upward. Also, what is the magnitude of the re- sultant? F₁ = 500 N -00 00 y ooo B FB = 400 N X
Practice 4.1.7 Two identical 20-mm - 200 mm thick plates are bolted to the top and bottom flange to form the built-up beam. 20 mm a) If the beam is subjected to a shear force of V = 250 kN, determine the allowable maximum spacing s of the bolts to the nearest mm. Assume each bolt has a shear 10 mm 300 mm capacity of 30KN, and I = 307.5E-6 m*. 10 mm b) What is the M, (plastic moment) of the beam assuming bolts can take infinite shear and o, = 250 MPai '10 mm 20 mm 200 mm
The bracket shown carries an eccentric load P at an eccentricity e=400mm. The column and bracket are A36 steel. Diameter of bolt is 22mm in standard holes. Assume that the column flange and the bracket are thick enough that single shear in the bolts will control. Shear capacity of one bolt is 45KN. a. Determine the polar moment of Inertia of the bolt group b. Determine the maximum load P that the bolted connection can support. C. Determine the direct load carried by the most critical bolt d. Determine the load due to moment carried by the most critical bolt. e = 400 mm 75 751 15 75 75 70 70
A vertical rod is attached at point A to the cast iron hanger shown. The force in the rod is 10 Kips acting downward. Determine (a) the stresses at points C and D, (b) the position of the neutral axis. 1 in. -3 in. A av 1.5 in. 10 Kips a 1.5 in. O B 3 in. C Section a-a D 0.75 in. ↑ 0.75 in. T
SOLVE FOR THE FORCE IN MEMBERS AB, AC, BC, CD, BD, BE, DE, DF & EF. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND WRITE WELL ALSO SEE LINK UNDER WEEK7 0.8m 2.4m -6KN MEMBER AB AC BC CD BD BE 2m ED DF EF 1m 8KN Av REACTION hinge) EX REACTION @roller) 3m SUMMARY OF RESULTS FORCE 1m 10KN 2.4m 3KN NATURE(I or C)
The connection shows 12 rivets joining a flat plate to the main member. Determine the load of the most heavily loaded rivet of the bolted connection in KN if P=60KN
5.42 The wall bracket shown is pin-connected at points A, B, and C. Calculate the pin reactions at these points. Neglect the weights of the members. INVI VOA 4'-0" A 4'-0" 1200 lb D 1600 lb 4'-0" 60° 30° 4'-0" B ENE M318074 baba