The cables AC and BC supports a load W with L= 20ma. If x1 = 7m and d= 2m what is the normal stress at both cables when loaded with W=60kN with cables’cross sectional area is 20mm2 The cables AC and BC supports a load W with L= 20ma. If x17m and d= 2m what is the normal stress at both cables when loaded with W=60kN with cables'cross sectional area is 20mm^2x1x2BAWс

Answered: Image /qna-images/answer/4bb72589-b08e-46a8-8663-7ce3df8d4a25.jpg

Answered: The cables AC and BC supports a load W…

The cables AC and BC supports a load W with L= 20m a. If x1 = 7m and d= 2m what is the normal stress at both cables when loaded with W=60kN with cables’ cross sectional area is 20mm2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Is strike fault affects and influence the tunnels?

A: Effect of strike fault on tunnel.

Q: 2.58 Knowing that a 0.02-in. gap exists when the temperature is 75°F, determine (a) the temperature…

Q: with th 8 14 28 35 70 100 200 pan 2.362 1.168 0.589 0.417 0.295 0.147 0.074 Sieve No. Diameter (mm)…

Q: appus Theorem, find the volume formed by revolving about the x-axis the area bounded in the 1st…

Q: If the soil sample is having a plastic limit of 28%, natural moisture content of 44% and a liquidity…

A: plastic limit = 28% = Wp moisture content = 44% = Wn liquidity index = 0.55 = IL It has been asked…

Q: STRENGTH OF MATERIALS The compound shaft, consisting of a solid steel (diameter = 140 mm) segment…

A: Given data in question Length Diameter Thickness Modulus of rigidity Shear stresses Angle of…

Q: 8-4. Determine the magnitude of the load P that will max = 30 ksi in the link ause a maximum normal…

A: This question is related to the Strength of Material.

Q: A light train made up of two cars connected by a coupling is traveling at 80 km/h when the brakes…

A: The given figure is shown below:

Q: Q3/The following not refer to three-level section Station Left Center 1 +0.95/5.25 +1.00/0 Right…

Q: 1.25-in. diameter d 2.15 A single axial load of magnitude P = 15 kips is applied at end C of the…

A: This question is related to the Strength of Material. "Since you have asked multiple question, we…

Q: Situation 1: A W8x67 has a length of 7.50 m. Fy = 248 MPa. The properties are given below.…

A: Answer Allowable axial capacity of Column 'Pa' for ASD can be calculated using Nominal axial…

Q: 2. Find the force in bar CG using METHOD OF JOINTS. B C D 16' A 12'. H 8k -12' G ▷ V 2k -12'- F E 4k…

A: In method of joint, Each joint is individually cut it and use of two equilibrium condtion (ΣFx = 0…

Q: 2 t B * RB 100 lb/ft . 4 t C M = 1200 lb - E ਦੇ D 1t|1t RE

Q: A watershed is 2500 kilometer squared in area and receives 1300 mm of rainfall in a year, the…

Q: Estimate volume of this beam. Length of beam=5m 6016mm 60 16 mm Section 1-1 y u oz qo -0.40 m-

A: From the given section, Width of the beam, B = 0.40 m Depth of the beam, D = 0.40 + 0.20 = 0.60 m…

Q: Steel A=2.0 in.² E = 29 × 106 psi Aluminum A = 1.25 in.² E = 10 x 10⁰ psi A = 900 mm² -500 mm 15…

Q: Compute the volume of discharge over the watershed (m³) by computing the area under the hydrograph…

Q: r and bending mome

Q: The composite member is shown in the figure. If the rigid bar remains horizontal after the loading…

A: Given data Steel member properties Es = 200GPa = 2 × 105 N/mm2 As = 700 mm2 Ls = 500 mm αs = 11.7…

Q: a 20 mm diameter steel pipe is used to drain and oil tank (SG-0.88) as shown. The total head loss is…

Q: Q2: A road embankment is 8 m wide and 200 m in length at the formation level, with a side slope of…

A: Embankment : An embankment is a volume of earthen material that is put and compacted to raise the…

Q: C

A: Ans : Section C - C Represent Vena Contracta

Q: a) Find the allowable load on the foundation by Terzaghi method, assuming a general shear failu with…

A: Answer Net allowable load = Qall Cohesion C =13 kpa Dry Unit weight of soil (γd) =17 Kn/m3…

Q: 15. Consider the steady, two-dimensional, incompressible velocity field given by V- (u, v) (1.3…

Q: mine the force in mem ular Howe truss shown mine by inspection the

Q: Problem 5: A steel member of circular cross section is subjected to a torsional stress that varies…

Q: Balili watershed us 2500 square kilometer in area and receives 1300 mm of rainfall in a year. The…

Q: A weir on a permeable foundation with downstream sheet pile is shown in the figure below. The exit…

A: Khosla's theory : It is stated that water does not creep along the bottom contour. It follows a…

Q: 3. A chemical reaction of a certain substance decays at a rate proportional to the undecayed amount.…

A: Given data of a Chemical substance :- Initial amount (No) = 500 After 2 days Substance lost = 150…

Q: SITUATION 2 Using Muller Breslau’s Principle, a) draw the influence line diagram for Vc; b) draw…

Q: m 2 ate for the support reactions of the following bea 60 KN 40 kN/m 120 kN m The 3 m D min

Q: Determine the following: a. Shear and Bending Moment Equation b. Shear and Bending Moment Diagram c.…

Q: B At a horizontal curve portion of a 4 lane undivided carriageway, a transition curve is to be…

Q: For a circular slab carrying a uniformly distributed load, the ratio of the maximum negative to…

A: As we know that, Maximum negative radial moment = 3WR216 Maximum positive radial moment = 6WR216

Q: The soil is having unit weight of 20 kN/m³ and depth of foundation is equal to 1.2 m, If the net…

Q: Q.2) A state of stress is specified as shown in Figure (2), By using Mohr's circ determine the…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(40+802)2+502R=78.1…

Q: A 12 ft long W12 × 96 (50 ksi steel) is used as a beam-column in a braced frame. It is bent in…

Q: A circular footing with a 1.5 m diameter is to be constructed 1.22 m below the ground surface. The…

A: Given:Diameter of the footing, D=1.5 mAngle of friction=25oFooting depth, df=1.22…

Q: For a circular slab carrying a uniformly distributed load, the ratio of the maximum negative to…

A: circular slab carrying uniformly distributed load is given and it has been asked to find ratio of…

Q: 6.5 A site is underlain by about 14 m of hydraulic fill sand with the following properties. Grain…

A: Given data:- Saturated unit weight = 18.8 kN/m3 Average uncorrected SPT resistance, N = 6 blows/ft.…

Q: MOHRS 10min зомра зопра 10 min 2

Q: Q.2) A state of stress is specified as shown in Figure (2), By using Mohr's circle determine the…

A: Radius of the circleR=(σx-σy2)2+τxy2R=(40+802)2+502R=78.1…

Q: SITUATION 1 Using Muller Breslau’s Principle, a) draw the influence line diagram for Vc; b) draw…

A: Given :

Q: What is the maximum permissible value L (m) if P = 11.8 kN and the allowable bending stress is 30…

Q: From the figure shown, determine the discharge of water at the trapezoidal weir if C = 0.75 + -*.…

A: Given data in question Width Height Coefficient Side slope To find out Discharge

Q: The soil is having unit weight of 20 kN/m³ and depth of foundation is equal to 1.2 m, If the net…

Q: 16 36 64 200 400 1440 2 160.00 Q2) the following results were obtained from odometer test on…

Q: The soil is having unit weight of 20 kN/m³ and depth of foundation is equal to 1.2 m, If the net…

A: Given data: Soil unit weight, γ=20 kNm3 Depth of foundation, D = 1.2 m Net bearing capacity, qu=2532…

Q: From the Levels of Biodiversity discussed. Pick one (1) level and cite one (1) example of that…

Q: The soil is having unit weight of 20 kN/m³ and depth of foundation is equal to 1.2 m, If the net…

A: Unit weight of soil = 20kN/m3 depth of foundation = 1.2m Qnet = 2532 kN/m2 FOS =3 It has been…

Concept explainers

Bars

In civil engineering, bars refer to steel reinforcement bars or rebars. These are structural members primarily used for reinforcement purposes in masonry works. A bar is characterized by its cross-sectional area, which is negligible compared to its length. Bars are usually manufactured by steel which is uniform throughout the length, or by meshing multiple steel wires. Other materials of the bar include carbon steel, glass fiber, carbon fiber, and basalt fiber. The reinforcing bars are coated with epoxy resins and other materials to enhance some of their properties including corrosion resistance.

Question

The cables AC and BC supports a load W with L= 20m

a. If x1 = 7m and d= 2m what is the normal stress at both cables when loaded with W=60kN with cables’
cross sectional area is 20mm²

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

For the truss shown, calculate the stress in area of each member BD. The cross-sectional member is 1200mm². 4m B 6m U 3m 4m E 3m 100KN 200KN F M FLSNI
Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
From the bracket connection shown. 1. Which of the following gives the stress due to axial load. a. 62.07 MPa b. 75.56 MPa c. 52.89 MPa d. 19.34 MPa 2. What is the value of ‘b’ that will make the maximum stress due to moment equal to that due to axial load? a. 150 mm b. 200 mm c. 250 mm d. 300 mm 3. What is the eccentricity? a. 300 mm b. 250 mm c. 150 mm d. 196.78 MPa
In the steel structure shown a 6 mm diameter pin is used at C and 10 mm diameter pin is used at B. The ultimate shearing stress is 150 MPa at all the connections. What is the largest P that can be applied? Front view 160 mm 18 D -18 Top view 120mm C D 6 mm 8 Side view
11. Link BC is 6 mm thick and is made of a steel with a 450-MPa ultimate strength in tension. What should be its width w if the structure shown being designed to support a 20-kN load P with a factor of safety of 3? 600 mm- A B 90 480 mm
For the beam shown in Figure (1), determine: a) The stresses in rods AB and BC. The cross-sectional area of rod AB is 155 mm2, and for BC is 200 mm?. b) The average shear stress in bolt at pin A. 1500 N S5 15 m 600 N/mt m- -3 m- Figure (1)
1. For the riveted connection shown in the figure using elastic analysisa. Determine the safe value of P if the allowable shearing stress of 25mm rivets is 150MPab. Determine the maximum shearing stress that can be develop in the rivet for a given load ? = 52??c. Determine the minimum shearing stress that can be develop in the rivet for a given load ? = 52?N
Determine the largest weight “W” that can be supported by the two wires AB and AC. The working stresses are 100MPa for AB and 150MPa for AC. The cross sectional area of AB and AC are 400mm2 and 200mm2 Compute “W” due to the stress capacity of AB Compute “W” due to the stress capacity of AC. Determine the safest value of “W”.
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
10. The hoisting beam assembly shown is supported by two 20- mm-diameter bolts at A and a 150 mm x 200 mm plate at B. In this problem, a = 1.2 m and b = 2.8 m. If the allowable tensile stress of the bolts at A is 112 MPa, which of the following gives the maximum safe value of W in KN? A. 45 C. 30 B. 60 D. 15 ZEIT 0 a BEEN H 8804 pe (cAPlate B to tried man 11 of 1911 b bell 110 mb llame lis To 102 W 20-102 bugil noitsuta
2. For the truss shown below, determine the stress in members AC and BD. The cross-sectional area of each member is 850mm². [94.12, 78.42 MPa] A 000 RA B 70kN E 4 panels at 4m 16m = G 30kN H RH 3m
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068