The coefficients of permeability of a soil in horizontal and vertical directions are 3.46 and 1.5 m/day respectively. The base length of a concrete dam resting in this soil is 100 m. When the flow net is developed for this soil with 1:25 scale factor in the vertical direction, the reduced base length of the dam will be

The coefficients of permeability of a soil in horizontal and vertical directions are 3.46 and 1.5 m/day respectively. The base length of a concrete dam resting in this soil is 100 m. When the flow net is developed for this soil with 1:25 scale factor in the vertical direction, the reduced base length of the dam will be

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter7: Permeability

Section: Chapter Questions

Problem 7.22P: Refer to Figure 7.24. The following data were collected during the field permeability measurement of...

See similar textbooks

Similar questions

A soil has a discharge velocity of 6 × 107 m/s and a void ratio of 0.5. What is its seepage velocity? 13x10 m/s 2 6x 10 m/s 3 12 x 10 m/s 4. 18 x 107 m/s
From the figure shown 1. What is the equation in determining the equivalent coefficient of permeability in the horizontal direction. 2. What is the equivalent coefficient of permeability in the horizontal direction if each soil layer is 3 m. thick and has the given values of K1, K2, K3 and K4. 3. What is the total flow if iav = 0.70
A confined aquifer is 6 m thick and the coefficient of permeability in the soil is 2m/day-m2. Two wells tapped on the aquifer are 100 m apart, and the difference in the water elevation in the wells is 3.0 m. The effective porosity is 0.38. What are the average (Darcy) velocity through the aquifer and the flow rate per meter width of aquifer? Darcy velocity is 0.06 m/day and the flow rate is 0.36 cubic meter per day per meter width. Darcy velocity is 0.16 m/day and the flow rate is 0.06 cubic meter per day per meter width. Darcy velocity is 0.16 m/day and the flow rate is 0.36 cubic meter per day per meter width. Darcy velocity is 0.06 m/day and the flow rate is 0.16 cubic meter per day per meter width. The best answer is not among the choices.
Refer to Figure 7.24. The following data were collected during the field permeability measurement of a confined aquifer using a pumping test. Determine the hydraulic conductivity of the permeable layer. Use Eq. (7.49). Thickness of the aquifer, H = 4.5 m Piezometric level and radial distance of the first observation well: h1 = 2.9 m; r1 = 17.8 m Piezometric level and radial distance of the second observation well: h2 = 1.8 m; r2 = 8.1 m Rate of discharge from pumping, q = 0.5 m3/min
A 0.7m long soil specimen is subject to a steady-state flow, as shown in Figure Q4. The saturated unit weight of the soil is 20 kN/m?. Determine the following: Water 0.3 m 0.8 m 0.3 m Datum 0.4 m Y Figure Q4 a) Total head (m) at point A, B and C. b) Elevation head (m) at point A, B and C. c) Porewater pressure head (m) at point A, B and C. d) Total stress (kPa) at point A, B and C. e) Porewater pressure (kPa) at point A, B and C. f) Effective stress (kPa) at point A, B and C. g) Seepage force per unit volume of soil.
For a falling-head permeability test, the following values are given: Length of specimen = 200 mm %3D Area of soil specimen = 1000 mm^2 %3D Area of standpipe = 40 mm^2 Head difference at time t = 0 = 500 mm Head difference at timt t 180 seconds = 350 mm %D %3D Determine the hydraulic conductivity of the soil in x10 4 cm sec
Q1: A saturated Sample of clay with an SL of 25% has a natural water content of 35%. What would its dry volume be as a percentage of its original (natural) volume if Gs = 2.72.
For a constant-head permeability test in a sand, the following are given: (L = 300 mm, Water collected in 3 min = 620 cm^3, A = 175 cm^2, Void ratio of sand = 0.58, h = 500 mm). Determine the seepage velocity.
2. For a falling head permeability test, the following are given. Length of specimen is 380 mm, are of specimen = 6.5 cm², hydraulic conductivity of soil specimen is 0.175 cm/min. a. What should be the area of the stand pipe for the head to drop from 650 cm to 300 cm in 8 min? b. Compute the the interstitial velocity under the test condition if the soil specimen has a void ratio of 0.50 in cm/sec. the head difference at time equal to 6 min. c. Compute
1. (30 pts) The soil profile shown below consists of 10 meters of sandy silt overlying gravel. The pore water pressure at the top surface of the silty sand is zero and can be assumed to remain zero. a) Calculate the level to which water would rise in a piezometer tube inserted into the top of the gravel if the silty sand is just stable? Use submerged unit weights and seepage forces to arrive at your answer (do not calculate total stresses and pore water pressures). Express your answer as an elevation, e.g. "Elev. 130". (Note: Elevations are in meters) (10 pts) b) Using the piezometric elevation calculated in part (a), calculate the pore water pressure at the bottom of the silty sand if the silty sand is just stable (10 pts). c) Calculate the total stress at the base of the silty sand and show that it is equal to the pore water pressure calculated in part (b) (10 pts) Elev. 120 m. Elev. 110 m. Sandy Silt (saturated) Void ratio, e = 0.68 G = 2.65 Gravel
SITUATION 1: A sample of silty clay has a volume of 14.88 cm3, a total weight of 28.81 g, a dry weight of 24.83 g, and a specific gravity of 2.7. 1. Determine the void ratio. a. 0.568 c. 0.7 2. Determine the degree of saturation. a. 0.568 c. 0.7 3. Determine the buoyant unit weight. a. 18.98 kN/m3 b. 16.37 kN/m? c. 10.31 kN/m³ d. 9.18 kN/m3 b. 0.618 d. 0.92 b. 0.618 d. 0.92
Given that: • Hydraulic gradient = 0.43 • unit weight of the saturated soil layer = 19.80Kn/m³ • rate and direction of seepage = 4.29 x 10^-4 m³/s (upward) • moisture content of the fully saturated soil layer = 24.25% Answer the ff: a) What would be the critical value of h to cause boiling b) If the value of h= 1.5 m boiling will? and If the value of h= 4.0 m boiling will? c) The total stress at point B d) The effective stress at point B e) The neutral stress at point B