The conduit in the figure has a diameter of 3 cm and is made of cast iron (ε= 0.26 mm). The fluid being transported is an oil with (p = 886 kg/m3) and (μ = 823 cp). For the given pressure data, determine (a) whether the flow is ascending or descending and (b) the flow rate being handled. Consider that friction losses are NOT negligible.

The conduit in the figure has a diameter of 3 cm and is made of cast iron (ε= 0.26 mm). The fluid being transported is an oil with (p = 886 kg/m3) and (μ = 823 cp). For the given pressure data, determine (a) whether the flow is ascending or descending and (b) the flow rate being handled. Consider that friction losses are NOT negligible.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is stored in a tank sketched in the figure below to support the demand of a nearby community area.The system is designed so that pressure at the location B always lies in the range of 330 to 440 kPa (gauge).Water demand fluctuates between 0.3 and 1 m3/s regardless of pressure at B. The supply pipe of 600 mmdiameter and 1 km length between A and B is made of steel and has the equivalent sand roughness of 1 mm.Although not shown in the figure, the supply pipe has five 90◦ bends, each having the head loss coefficientof 0.8. The figure shows that the bottom end of the tank is located 42 m above the ground, and the pipe isburied 1.5 m below the ground. A pump system regulates so that the tank keeps the same water level all thetime. Assume water at 20◦C, and air in the storage tank has the atmospheric pressure. To meet the designcriterion for pressure at B, what should be the depth of water h in the storage tank?
On a single plot, show curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure should be 0 to ~1 MPa). Pipe inner diameter: 0.03 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters), (provide your answer with four decimal points) P Type here to search O 10°C Sunny AQA ENG 0029 16/02/2022 DELL priSc FS F6 5 E R J K L %23 F E Aock C V sage page VO at gr ctri
On a single plot, plot three curves that show the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below. Delta P on y axis and flow rate on the x axis. The pressure range is 0 to 1 MPa. (Branches 1 and 3 are in the same plane; branch 2 is located 5 m above the other two branches. Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
Use= Resolving of Example (1-3) Two reservoirs with a difference in elevation of 15 m are connected by the three pipes in series. The pipes are 300 m long of diameter 30 cm, 150 m long of 20 cm diameter, and 200 m long of 25 cm diameter respectively. The friction factors for the three pipes are, respectively, 0.018, 0-020 and 0-019, and which account for friction and all losses. Further the contractions and expansions are sudden. Determine the flow rate in l/s. The loss co-efficient for sudden contraction from dia. 30 cm to 20 cm = 0.24. Le-L₂ (D.) ² Le = L3 (D₁) ² 5 D3 LT. L₁ + L₂ ( D₁ ) ³ + L3 (D²₂) ³ 5 5 D3
Plot curves on a single plot that display the relationship between the pressure generated by thepump as a function of flow rate of water at 20 °C through the three branches of the piping systemshown below (delta P on the y axis and flow rate on the x axis; therange of the pressure as 0 to ~1 MPa). Pipe inner diameter: 0.0254 mPipe material: copperTypical mass flow rate of interest: 0.5 kg/sIgnore minor losses of tee's at points A and B and any features of branch 3Consider minor losses of two 90° elbows in branch 2
Q3/ A petroleum crude oil having a kinematics viscosity 0.0001 m²/s is flowing through the piping arrangement shown in the below Figure,The total mass flow rate is equal 10 kg/s entering in pipe (A) . The flow divides to three pipes ( B, C, D). The steel pipes are schedule 40 pipe. note that the dynamic viscosity 0.088 kg/m.s. Calculate the following using SI units: 1- The type of flow in pipe (A). 2- The mass velocity in pipe (B) GB. 3- The velocity in pipe (D) Up. 4- The Volumetric flow rate in pipe (D) QD. 5- The Volumetric flow rate in pipe (C) Qc. Oe = 2 o mm UB = 2UA Perralenm crude oL mic =? -> ma = 1o Kg/s = 50 mm Go 7000 K/m.s %3D Note that!. = 30 mm D: 0iameter, UIvelocity G mass velocity mass How ate.
SOLVES TEP BY STEP DONT USE CHATGPT DONT USE AI 3. An oil of viscosity 1.8 cp and relative density 0.8 is contained in an open tank located above the application site. A 1.5-inch diameter pipe extends vertically from the bottom of the tank and is 5 m long. The oil level in the tank remains constant at 3 m above the bottom of the tank. In a case with friction the discharge speed can be obtained in the form of the following Equation. Calculate the flow rate of oil discharged per hour. Assume that the pipe is commercial steel (ε=0.05 mm). V= 2gh +f-
G1/ In the fig.shown, the Flow rate Pipe (A) is equal ( QA = 25 Lit15), the diameter is equal ( DA = 75 mm, D, = De = Dc =30mm), and the velocity in Pipe (D) is equal (Uo=5 m/s), the relation between flow rate in in 6o mm, Pipe (B) and pipe (c) GB =3 Qc. Find the Value of '. Re, Qc, Qo. 2- UA, UB, Uc: Pe = 30 mm water Pc = 30mm imput QA = 25 2i+/sec OA= 75 mm = 6o mm input = A outPut = B, C, D accumulation = o.
Answer with True or False of the following question: (7M 1. Water flows steadily down a vertical pipe of constant cross section. Neglecting friction, according to Bernoulli's equation, velocity decreases with height. 2. A liquid in an open right circular cylinder is given rigid body rotation about the axis of the cylinder. The pressure distribution in any vertical plane is uniform. 3. A curved surface is submerged in a static liquid. The horizontal component of pressure force on it is equal to the pressure force on a vertical projection of the surface. 4. A U-tube manometer measures the difference in total energy between two points.
Given: diameter of pipe in point 1 = 3.9indiameter of pipe in point 2 = 2.5inspecific gravity of the liquid = 0.79h(ft) = 0.60ftpressure at point 1 = 14.6 psiapressure at point 2 = 49 psiapump and motor efficiency = 66%diameter of pipe in point 4 = 4.5indiameter of pipe in point 5 = 2.3 inZ3 = 35ft With the schematic diagram of a pump, tanks, and piping determine the following:1) The velocity of the liquid at point 2 (ft/s)2) Pump work used by the liquid (Wpump U) (hp)3) Electric motor power in out (kW)4) In figure 3, the shaded (pink) in the U tube is mercury; determine y. specific gravity of mercury 13.75) Mass flow rate
As a process engineer, you are designing a new drinking water treatment plant using conventional treatment process including Two Rapid Mixers as follows: The design flow is 50 million gallons per day (MGD) (1 Gallon = 3.785 L, 1 m³ = 1000 L). The average temperature of water is 5°C with a dynamic viscosity, μ = 1.519 x 10-3 Pa.Sec In each rapid mixer with a square shape, detention time, e = 1 min, water depth H = 13 ft, and power input P = 1.5 kw (1 ft = 0.3048 m, 1 KW = 1,000 W) The equivalent diameter, TE for each rapid mixer is ________ m. TE || AIR 1) 4.1 2) 4.4 3) 4.6 4) 4.8 5) 0.4