The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensionsare in mm.30015010040°25 kN20 kNFigure 3.5 – 7A) Determine the stress on rod AB if it is 16 mm diameter.Select one:а. 106 MPаb.Р 112 МPас. 118 МPаd. 129 MPaB) Determine the required diameter of the pin at C if the maximum allowable shear stress is180 MPa in double shear.Select onea. 18 mmb. 16 mmc. 20 mmd. 12 mm

Answered: Image /qna-images/answer/0ecdb5d4-d6ce-402f-b4e4-0f3c3c7fbb4d.jpg

The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA 300 150 100 40° 25 kN 20 kN Figure 3.5 -7 A) Determine the stress on rod AB if it is 16 mm diameter. Select one: a. 106 MPa b.Р 112 МPа с. 118 МPа * d. 129 MPa B) Determine the required diameter of the pin at C if the maximum allowable shear stress is 180 MPa in double shear. Select one a 18 mm b. 16 mm c. 20 mm d. 12 mm

The control arm is subjected to the forces as shown in Figure 3.5 – 7. All dimensions are in mm. TA 300 150 100 40° 25 kN 20 kN Figure 3.5 -7 A) Determine the stress on rod AB if it is 16 mm diameter. Select one: a. 106 MPa b.Р 112 МPа с. 118 МPа * d. 129 MPa B) Determine the required diameter of the pin at C if the maximum allowable shear stress is 180 MPa in double shear. Select one a 18 mm b. 16 mm c. 20 mm d. 12 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The shear stress is maximum on the principal plane Select one: O True O False
The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 19616 lb is applied at A? The d = 0.65-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
Required information Forces are applied at points A and B of the solid cast-iron bracket shown. The bracket has a diameter of 0.8 in. Take P = 2300 lb. B 2.5 in. 600 lb 1 in. The principal stresses are: ksi A Determine the principal stresses and the maximum shearing stress at point H. (Round the final answers to two decimal places. Input the answers with the appropriate sign.) 3.5 in. max omin = ksi The maximum shearing stress is ksi.
The uniform 3-Mg bar is supported by a smooth wall at A and pin connected a B (double shear). Determine the diameter of the smallest pin that can be used without exceeding the allowable shearing stress in the rivet is 70 MPa. Express your answer in "mm" to the nearest whole number. Note: Use the rule in rounding-off numbers (normal rounding-off). DO NOT PUTA UNIT IN YOUR ANSWER, only the numerical value is required* 10m
1-26. What is the required diameter of the pin Bfor the bell crank mechanism shown in the figure if an applied force of 60 kN at A is resisted by a force P at C? The allowable shearing stress is 100 MPa. Ans, 23.2 mm. 60 N A 150 mm 300 mm Pin B
Question 5 Determine the outer diameter (mm) of a tubular rod subjected to an axial force of 22 kN if it developed a stress of 40 MPa. Take note that the inner diameter is 4/6 of the outer diameter.
3) A 25 mm solid round shaft is supported by self-aligning bearings at A and B (the bearings do not support axial loads). Two chain sprockets are attached to the shaft as shown. a. Find the force, F, on the 125 mm diameter sprockets. b. Construct the V-M-N-T diagrams for the shaft. c. Determine the shaft location with the most severe state of stress. d. Sketch the Mohr's circle and find the principal stresses at that location. A 125 mm dia. 50-mm dia. 75 mm 25mm dia. 5000 N 150 mm 75 mm
If the allowable normal stress is 120MPa and the allowable shear stress is 60MPa, what is the B diameter of pin?
1-63.M. The key in Figure 1-18 has the dimensions b = 10 min, h = 8 nim, and L = 22 min. Determine the shear stress in the key when 95 N-m of torque is transferred from the 35-mm-diameter shaft to the hub. Hub End view Shear plane Shear pl T=Torque -D=Shaft diameter T=F(D/2) F₁-Force of shaf F₂= Force of hub on 1 Shear area=A,=bxL
NEED ANSWER ASAP THANK YOUU The right-angle bar is supported by a pin at B and a roller at C. What is the shear stress in the pin in psi if a load of P = 20144 lb is applied at A? The d = 0.79-in.-diameter pin is in double shear. Round off the final answer to two decimal places.
The plate shown in the figure is fastened to the fix by three 10mm diameter rivets. Compute the value of the loads P so that the shearing stress of any rivet does not exceed 70 MPa. Express your final answer in Newton to the nearest whole number. Do not include the unit in your answer. 180 mm 100 mm | 150 mm
The horizontal cross-section of the cast-iron standard of a vertical drilling machine has the form shown. The line of thrust of the drill passes through P. Find the greatest value the thrust may have without the tensile stress exceeding 15 MN/m2. What will be the stress along the face AB? (Cambridge) ANSWER: 17.68 kN; 11.8 MN/m2 compressive.