The copper shaft is subjected to the axial loads shown. Determine the displacement of end A with respect to end D if the diameters of each segment are dAB = 29 mm, dec = 54 mm, and dcD 14 mm. Take Ecu = 125 GPa. 36 kN -2m- 22.5 kN A22.5 KN B -3.75 m- 2.5 m- 9 kN C 9 kN 27 kN The displacement of end A with respect to end D is .......... mm Note: Please enter your answer with three significant digits after the decimal point.

The copper shaft is subjected to the axial loads shown. Determine the displacement of end A with respect to end D if the diameters of each segment are dAB = 29 mm, dec = 54 mm, and dcD 14 mm. Take Ecu = 125 GPa. 36 kN -2m- 22.5 kN A22.5 KN B -3.75 m- 2.5 m- 9 kN C 9 kN 27 kN The displacement of end A with respect to end D is .......... mm Note: Please enter your answer with three significant digits after the decimal point.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

diumitee 1 Find thi diumeec of a cimeulon Shaft subjeeted to a momint (T=3 KN.m) if the thi shaft is (60M Pa] and the allon abi engle ofZaist of a cineulan twisting e allowable Shean szhesg in Pen uniz length s Take (G =70 G Pa)?
A 75mm shaft is subjected to 5KN-m torque. Find the stress developed in MPa. Meanwhile, determine the maximum mean diameter of a taper for use to fix a lever to a shaft. If it transmit a maximum torque f 750 in-lb . The shaft diameter is in 3in
A compound shaft consists of two solid shafts that are connected at flange B and attached to rigid walls at A and C. The shafts are made of same material, having shear modulus G80 Gpa and different diameters di and de Determine the internal twisting moments at A Here di = 0.2 m, d₂ = 0.1 m. L₁ = 1 m. L₂ 1 m. M. 100 N-m. 4 Mo Select one: O 1. 60-70 N-m O 2. 80 – 90 N-m O3.70-80 N-m O 4.50-60 N-m O 5.90-100 N-m
The copper shaft is subjected to the axial loads shown. Determine the displacement of end A with respect to end D if the diameters of each segment are dAB = 0.75 in., dBC = 1 in., and dCD = 0.5 in. Take Ecu = 18(103) ksi.
Finding the value of sectional modulus of shaft having diameter 3 m
SS 304 steel shaft is 3 m long and has an outer diameter of60 mm. When it is rotating at 60 rad/s, it transmits 30 kWof power from the engine to the generator. Determine thefollowing: a. The smallest thickness of the shaft if the allowableshear stress is 150 MPa and the shaft is restricted notto twist more than 0.08 rad. Use G for steel = 83 GPa. b. The percentage savings in weight had the generatorutilized a solid shaft. Assume same material, length andtorque capacity.
A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
Determine the diameter of a solid steel shaft that will transfer 30 MW at 1500 RPM with a 1 degree twist angle for every 20 diameters of length. G=80GN/m2. Give me the solution of this please. Ans. D = 3.03 m
Q3-C- The 304 stainless steel shaft with modulus of rigidity 75 GPa and 3 m long has an outer diameter of 60 mm. When it is rotating at 60 rad/s, it transmits 30 kW of power from the engine E to the generator G. Determine the smallest thickness of the shaft if the allowable shear stress tallow= 150 MPa., and the shaft is restricted not to twist more than 0.08 rad. R TUD
A hollow bronze shaft of 75 mm outer diameter and 50 mminner diameter is slipped over a solid steel shaft 50 mm indiameter and of the same length as the hollow shaft. The twoshafts are then fastened rigidly at their ends. Find the maximumshearing stress developed in the bronze by end torque of 3 kN.mFor bronze G = 35 GPa and for steel G = 83 GPa.
The shaft consists of three concentric tubes, each made from the same material and having inner and outer radii as given below. Length of shaft is 2m. One end is fixed to the wall and to the other end a disc is attached. If a torque of T =800 N.m is applied at the disc end, determine the maximum shear stress in the shaft. 1. Inner tube: r; = 20mm, r, = 25 mm 2. Center tube: r; = 26 mm, r. = 30 mm 3. Outer tube: r = 32mm, r, = 38mm
1. The 12 kN m torque is applied to the free end of the 6-m steel shaft. The angle of rotation of the shaft is to be limited to 3°. (a) Find the diameter d of the smallest shaft that can be used. (b) What will be the maximum shear stress in the shaft? Use G = 83 GPa for steel. 2. The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter is 75 mm and G = 35 GPa. For the steel segment BC, the diameter is 50 mm and G = 83 GPa. Given that a = 2 m and b = 1.5 m, compute the largest torque T that can be applied as shown in the figure if the maximum shear stress is limited to 60 MPa in the bronze and 80 MPa in the steel. 75 mm 50 mm A Bronze B Steel