The distance measured along a vertical line from a vertical datum to a point or object. f.The rod reading on a point whose elevation is desired. g.Differential leveling theory is expressed by two equations, which are repeated over and over. What are they? h.It used to specify the relative horizontal position of any point along the reference line. i.Specify at least 3 field survey party members and their specific rol

The distance measured along a vertical line from a vertical datum to a point or object. f.The rod reading on a point whose elevation is desired. g.Differential leveling theory is expressed by two equations, which are repeated over and over. What are they? h.It used to specify the relative horizontal position of any point along the reference line. i.Specify at least 3 field survey party members and their specific rol

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Remote Elevation ated to the bounde You have been asked to determine the bottom of steel elevation for the Cuyahoga Valley National Bridge. (X marks the spot) The surveyors in the field obtained the following data by setting up a total station on a point of known elevation. Use ONLY the APPLICABLE DATA Height of Prism= Height of Surveyor= Height of Total Station= Elevation of known point A= Horizontal distance to prism= Vertical angle to bottom of steel= 4.37 ft. 6.11 ft. 5.75 ft. 1248.86 ft. 122.88 ft. 26°22' 26°22' Bridge Q
Q.4. arithmetic check. Write your calculations in detail and fill the table. The units of readings in the table are meter (SI system). Please calculate elevations in the stations given in the table and show the Station BS FS H.I. Elevation ВМА 2.16 500.00 ТР 1 3.24 1.13 ТР 2 3.14 1.07 ТР 3 2.59 1.67 BM B 1.39
Surveying subject : a. Explain the principles of surveying? Support your answer with sketches. b. What is horizontal and vertical control in a survey? c. How shore line survey is performed? Note: Write the answer (b) in steps, neat & clean sketches are compulsory with (a) & (c).
topic: Tacheometry Pls answer in this format Identify the problem (with diagram) complete tabulation computations/solution final diagram with computed unknown variables determine: a) the stadia interval factor b) the horizontal distances DE and DF c) the differences in elevation between points D and E and points D and F
fundamentals of surveying. ERROR OF CLOSURE. determine the linear error of closure, the direction of the side of error, and the precision of the measurements made. Tabulate all observed and computed values.
While measuring a survey line using a tape between two stations A and B intervened by a hill a. Chainage free but vision gets obstructed b. Vision free but chainage gets obstructed c. Both chaining and vision gets obstructed O d. Chaining gets obstructed
Difference of Horizontal Angle and Vertical Angle in Surveying
Q.4. arithmetic check. Write your calculations in detail and fill the table. The units of readings in the table are meter (SI system). Please calculate elevations in the stations given in the table and show the Station BS FS Н. Elevation ВМА 2.16 500.00 ТР 1 3.24 1.13 ТР 2 3.14 1.07 ТР 3 2.59 1.67 BM B 1.39
Examples of indirect measurement in surveying
6789 6) Pythagorean theorem applies only to 7) Plumb bob is mainly used in the measuring of distance with a tape? 8) is a type of polygons with only one pair of opposite sides parallel. 9) The main difference between the horizontal distance and vertical distance is 10) The survey is used to determine the location of building corners. 11) Navigation and water resources planning projects depend upon data obtained from surveys 12) A is measured in a plane that is vertical at the point of observation or measurement.
Which of the following is not required in compass surveying? O a. Lengths of lines O b. Connecting lines O c. Bearing angles O d. Triangles
Plane surveying is that type of surveying in which the earth is considered to be a flat surface. Distances and areas involved are of limited extent and the a. spheroidal shape of the earth is considered b. exact shape of the earth is disregarded C. approximate shape of the earth is considered