the exit Q2) A 4 m high and 6 m wide wall consists of a long 18 cmx30 cm cross section of horizontal bricks (k= 0.72 W/m - °C) separated by 3 cm thick plaster layers (k = 0.22 W/m - °C). There are also 2 cm-thick plaster layers on each side of the wall, and a 2 cm thick rigid foam (k =0.026 W/m °C) on the inner side of the wall. The indoor and the outdoor temperatures are 22°C and -4°C, and the convection heat transfer coefficients on the inner and the rough the wall. outer sides are ho =10 W/m² °C and h₁ = 20 W/m² °C, respectively. Assuming one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer

the exit Q2) A 4 m high and 6 m wide wall consists of a long 18 cmx30 cm cross section of horizontal bricks (k= 0.72 W/m - °C) separated by 3 cm thick plaster layers (k = 0.22 W/m - °C). There are also 2 cm-thick plaster layers on each side of the wall, and a 2 cm thick rigid foam (k =0.026 W/m °C) on the inner side of the wall. The indoor and the outdoor temperatures are 22°C and -4°C, and the convection heat transfer coefficients on the inner and the rough the wall. outer sides are ho =10 W/m² °C and h₁ = 20 W/m² °C, respectively. Assuming one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.3DP

See similar textbooks

Similar questions

2. Calculate Passive House's energy demand. a, Calculate window U-value based on given data in figure. 0.117m 0.117m 0.134m C₂ Utotal Wglass-0.996m = 1.229m glass Uglass = 0.6- glass W window - 123m W m².c 0.117m 1.48m nwindow W m² °C Uframe = 1.6- Area₁ U₁ + Area2 U₂... + Area, * U₁ Area total b. With the calculated U value for the windows find out how much power needed to maintain 20°C in a home with outside of 0°C based on the following: the house having a square footprint 17 m by 17 m, walls 2.5 m high (Uwalls = 0.152 each of the four walls hosting two windows, and each window having an area of 2 m². The entry door area is 2.5 m² (Udoor = 0.65- ). What are the heat loss rates for the installed windows, the door, the walls, the ceiling, and the floor? What is the overall heat loss rate of the home? m². C 1. What do these calculated heat loss rate values mean? 2. What is the definition of the passive house? 3. What does the U-value represent? Use its unit as a hint and describe it…
6,000 ft of 7-in C-75 grade of casing string will be run in a borehole having a diameter of 8.5-m. The casing has a unit weight of 38 lbm/ft and a wall thickness of 0.540-in. Mud weight used to run the casing into the borehole is 10 lbm/gal (ppg). a) Calculate the weight of casing string in the air. b) Calculate the hook load when the casing is in the borehole. c) Calculate the borehole capacity in terms of bbl/ft. d) Calculate the borehole capacity in terms of bbl. e) Calculate the displacement of the casing in terms of bbl/ft. ) Calculate the displacement of the casing in terms of bbl, g) Calculate the volume of cement slurry to fill the annulus in terms of bbl and cuft assuming a excess volume factor of 1.5) h) Calculate the maximum length of the casing if the rig used for this operation can handle 250,000 Ibf of hook load. i) The casing gets stuck at bottom of the borehole while running the string. Calculate the maximum pulling force that the driller can apply at the surface to get…
Concrete wall 30 cm thick has 10 cm wide void (area 0.1 m²) in the middle as shown. Find temperature difference between behind the void (T.) and the surface of the intact wall, Tw. Assume: concrete = 0.76 W m¹ °C, Kair= 0.026 W m¹ °C, and hair = 5 W m² °C. T₁ = 32 °C T₂ = 17 °C air 10 cm Concrete Tv Tw
c) Calculate the rise of a liquid of density p= 0.8 g cm-³ inside a square straw, with the cross section given by a square of side L = 2 mm. The surface tension for the solid- liquid interface is st = 200 mJ m-2 and for the solid-gas interface Ysg = 250 mJ m-².
Q3) A thermometer having a surface emissivity of 0.85 is placed in an air space in a metal-walled building, the walls of which may attain a temperature of -10°C during winter climate conditions. The convection coefficient between the thermometer and the surrounding air is estimated as h = 10W/m2. C. If the thermometer indicates a temperature of 17°C, estimate the true air temperature in the building.
A modern cabin has a concrete floor that is 4.50 inches thick. Aroaring fire keeps the interior of the cabin at 21.0 0C while the airtemperature below the cabin is a chilly 2.00 0C. How much heat(J) is lost through the concrete floor in 4 hrs if the cabin measures4.50 m by 6.50m to 3 sig fig?
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?
Presents the diagram of the problem, necessary formulas, clearance and numerical solution: An iron plate 2 cm thick has a cross-sectional area of 5,000 cm2. One of the faces is at 150 ◦C and the other is at 140 ◦C. How much heat flows through the plate each second? For iron, kT = 80 W/m K.
Sipho’s mother is making a fire in the stove inside a shack using coal. A fan is used to extract the flue gasfrom the fire via a chimney made of zinc material. The wall thickness of Chimney is L=4mm and the walltemperature of the chimney on the flue gas side is T_si=60˚C. Sipho, playing outside next to the chimneyexperiences an ambient temperature of 20˚C. The surrounding temperature is T_sur=35˚C and the emissivityis ε=0.95. Assume the convection coefficient is 20W/m2K and the chimney is grey material.Under these conditions determine the outer surface (air side) temperature T_so=? of the chimney.
You are designing an enclosure which houses a PCB. Mounted outside the enclosure on its top is a set of aluminum fins, as seen in the sketch below. The enclosure (and fins) are 150mm deep long. There is no forced airflow. Neglect the thickness of the enclosure walls. Neglect heat transfer out of the sides and bottom of the enclosure. If the PCB produces 4000 W/m2: a) Most industrial-grade ICs have a maximum temperature of 85oC. If you must keep your PCB below this what is the maximum thermal resistance from the PCB to the air surrounding the fins? Assume the air around the fins stays at room temperature. b) If the top of the enclosure (and bottom of the fin base) runs at 50°?, what is the effective thermal conductivity above the PCB? Hint: Because the air inside the enclosure is trapped and heats up, any air properties NOT given below are calculated at the average air temperature (T1+T2)/2. c) What is the temperature at the base of the fins? d) What is the efficiency of the fins? e)…
1. A bubble (assuming perfectly spherical) was released from a depth of 120m in the body of water by a fish. Having its temperature constant while it travels from the depth of release to water surface, solve for the following: a. kPaabs when released b. bubble diameter at 60m depth c. bubble diameter at the water surface h2=60m h,=120m SG=1.03
1) The heat flux and surface temperature of a board are related to each other with the thickness written below. What is the heat conduction coefficient of the board? Accept conditions; a) One dimensional heat transfer in x direction, b) continuous heat transfer (stady state) c) properties do not change constantly. TA T = 60 C 9:-40W/m² T=20°C +L=0.05m