The frequency of the sinusoidal voltage source V, = V20 is adjusted in two separate cases as follows: Case a) Until the current i, is in phase with V.. Case b) Until the current i, has a phase of 45° with respect to V, For each of the two cases, find the radial (angular) frequency in terms of the circuit elements Ro. , C. If R, = 100, L = 10 mi and C = 10 uF determine the radial frequency in rad/s Ro Find the radial (angular) frequency when the current i, is in phase with the voltage V,

The frequency of the sinusoidal voltage source V, = V20 is adjusted in two separate cases as follows: Case a) Until the current i, is in phase with V.. Case b) Until the current i, has a phase of 45° with respect to V, For each of the two cases, find the radial (angular) frequency in terms of the circuit elements Ro. , C. If R, = 100, L = 10 mi and C = 10 uF determine the radial frequency in rad/s Ro Find the radial (angular) frequency when the current i, is in phase with the voltage V,

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Convert the following instantaneous currents to phasors, using cos(t) as the reference. Give your answers in both rectangular and polar form. (a) i(t)=5002cos(t30) (b) i(t)=4sin(t+30) (c) i(t)=5cos(t15)+42sin(t+30)
Segments of two sinusoids are shown in the plot below. Determine the phase difference between the two waveforms. Amplitude 0 2 -2 -4 0 180° 90 ° Oo° 0.5 Time (seconds) 1 1
2. Draw the phasor and wave diagram of the following sinusoidal current: Ii leads l2 by 35°, l4 leads l3 by 45°, Is lags l2 by 35°, l3 lags I, by 20°. Use l2 as reference. Average values of current are all equal to 40 A.
P.3: Find the rms value for the following sinusoidal waveforms a. v= 120 sin(377t + 60°) b. i=6x 10³ sin(2# 1000r) c. u=8 x 10-6 sin(2# 5000 + 30°) P.4: Find the rms value for the following sinusoidal waveforms a. v= 20 sin 754r b. v= 7.07 sin 377r c. i=0.006 sin(400r + 20°) d. i 16 x 10³ sin(377r - 10%) P.5: Write the sinusoidal expressions for voltages and currents having the following rms values at a frequency of 60 Hz with zero phase shifts: a. 4.8 V b. 50 mA c. 2 kV
3: Sketch be carefully e = 10 sin(754t +90°) with time in second. A: Determine the form factor for the following wouafor
ESSAY: Describe what happens to the power in this RLC series circuit as the capacitance decreases. Explain in general terms why the observed change should occur. Understand the effects of basic electrical components on the average power of the system and the concept of power factor. Differentiate between average power and real power.
Prob. I and Vc For the following RMS phasor circuit, a coworker has determined values for 50 Ohms 50 Ohms i,- 225 2253.13° = 190.92 + 254.56 VRMS R1 + R2 Vc = 237.17/26.565° = 212.13+ 106.07 VRMS 100 2 -3Z98.13° =-0.4243 + J2.970 ARMS C -j60 Ohms For this problem provide at least 3 digits of precision for the answers. The results for the following calculations are to be answered in - a) Find the current I b) Determine the real (P) and reactive(Q) power DELIVERED by the source c) Determine the real (P) and reactive (Q) power ABSORBED by each impedance ( resistors R1 and R2, inductor and capacitor). The values for P and Q can be positive or negative. Remember S =P+jQ, so do not include the j with your answer for Q. Each of these answers will require two parts. For the phasor a magnitude and angle will be needed. For the powers, The real power P and the reactive power Q are required.
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
P.4: Find the rms value for the following sinusoidal waveforms a. v = 20 sin 754t b. v = 7.07 sin 377t c. i = 0.006 sin(400t + 20°) d. i 16 x 10-3 sin(377t - 10°)
supply 3. Three circuits A, B and C are connected in series across 350 V supply. The voltage across circuit A is 80 V lagging the voltage by 330 and the voltage across circuit C is 140 V leading the supply voltage by 48°. Determine the voltage circuit B and its phase displacement from the supply voltage using wave and vector solution. across 4. Draw the phasor and wave diagram of the following sinusoidal current:
When a resistor is connected across the terminals of an ac generator (117 V) that has a fixed frequency, there is a current of 0.332 A in the resistor. When an inductor is connected across the terminals of the same generator, there is a current of 0.365 A in the inductor. When both the resistor and the inductor are connected in series between the terminals of this generator, what is (a) the impedance of the series combination and (b) the phase angle between the current and the voltage of the generator? Note: The ac current and voltage are rms values and power is an average value unless indicated otherwise. (a) Number (b) Number Buda i Vrms R Irms.R Circuit 1 Units Units Vrms. Irms, L Circuit 2 > L Vrms R www Circuit 3
Convert the following phasors into sinusoidal waveforms a. Vi = 100e30 V, w= 10' rad/s b. Vi = 120e45 V, w= 10³ rad/s c. I = 100e*45 A, w= 2*10 rad/s d. I1 = 240e 26.6 mA, w= 2*10* rad/s %3D