Read the question carefully... Please solve the question by using Mohr's circle method Problem 9.62The grains of wood in the board make an angle of 20° with thehorizontal as shown. Using Mohr's circle, determine the normaland shear stresses that act perpendicular and parallel to thegrains if the board is subjected to an axial load of P = 280 N(Figure 1)Part ADetermine the normal stress.Express your answer to three significant figures and includesHAFigureK 1 of 1ValueUnitsSubmitRequest AnswerPart B300 mm60 mmDetermine the shear stress.20Express your answer to three significant figures and include25 mmHAValueUnitsTeyUnknown (1).pdfUnknown.pdf

Given that:P=280 Nb=25 mmd=60 mmθ=20ο

The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's circle, determine the normal and shear stresses that act perpendicular and parallel to the grains if the board is subjected to an axial load of P 280 N (Figure 1)

The grains of wood in the board make an angle of 20° with the horizontal as shown. Using Mohr's circle, determine the normal and shear stresses that act perpendicular and parallel to the grains if the board is subjected to an axial load of P 280 N (Figure 1)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.2.17P: A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at...

See similar textbooks

Similar questions

At a point on the web of a girder on an overhead bridge crane in a manufacturing facility, the stresses arc known to be x = —4300 psi, a = 1700 psi, and r = 3100 psi (the sign convention for these stresses is shown in Fig, 7-1). A stress clement located at the same point in the structure (but oriented at a counterclockwise angle 0, with respect to the _y axis) is subjected to the stresses shown in the figure {b, r», and 2100 psi). Assuming that the angle 8Xis between zero and 90°, calculate the normal stress trA, the shear stress ta, and the angle Bv
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
A constant wind blowing against the side of this chimney has caused creeping strains in the mortar joints, such that the chimney has a noticeable deformation. Explain how to obtain the stress distribution over a section at the base of the chimney, and sketch this distribution over the section.
The internal loadings at a cross section through the 130-mm-diameter drive shaft of a turbine consist of an axial force of 12.5 kN, a bending moment of 1.2 kN m, and a torsional moment of 2.25 kN · m. (Figure 1). Part A Determine the principal stresses at point B. Express your answers using three significant figures separated by a comma. vec ? 01, 02 = MPa Submit Request Answer Figure 1 of 1 Part B Determine the magnitude of the maximum in-plane shear stress at point B. Express your answer to three significant figures and include the appropriate units. µA 12.5 kN Tmax = Value Units 1.2 kN m 2.25 kN m Submit Request Answer
Determine the state of stress at point A of the rectangular post shown loaded with concentrated forces directed along the y axis equal to 75kN and along the x axis equal to 15kN. 1)Determine the total normal stress along the x and y axes at point A (include if tensile or compressive in your final solutions) 75 kN 50 mm 200 mm- 150 mm OAx= 15 kN OAy= 2) Draw the state of stress of point A 800 mm A 50 mm
A thin walled spherical shell is subjected to an internal pressure. If the radius of the shell is increased by 19% and the thickness is reduced by 1%, with the internal pressure remaining the same, the percentage change in the circumferential (hoop) stress is
Problem 1: A state of plane stress at a point on the surface of a structure consists of the following stress components: Ox = 25 ksi, oy = 12 ksi, and Txy = 10 ksi. Note that the stress components act in the directions shown on the element below. Ox Txy 12 ksi 5 25 ksi 10 ksi (a) Draw a complete Mohr's circle for this stress state. Clearly label the X and Y faces, the center C, and the radius R. (b) Using Mohr's circle, determine the principal stresses, the maximum in-plane shear stress, and the normal stress that acts on the maximum shear stress plane. Label all of these quantities on the circle. (c) Calculate the orientation of the principal planes and the planes of maximum shear stress. Label all of these quantities on the circle. (d) Show all stresses from part (b) on properly oriented stress element(s). Be sure to include all stress components acting on the elements(s).
P= 200 lbs |=2" T 250 in-Ibs Qt. DRAW STRESS STATES いITH A SQLARE ECEMENT エN xY AXES Label with stress values Q2 DRAW MOHR'S CIRCLE AT A Q3.CALCULATE PRINCIPAL STRESSES AND DRAW THE PLANE FoR ri$ a IN THE SCHEHATIC Draw element rotated to principal planes and label with stress values and rotation angle
(a) Construct Mohr's circle for an element in a uniaxial state of stress (b) Use this Mohr's circle to derive the equation for the normal stress On and shear stress En on the n-face. The equations should depend on Ox and θ (c) Use the Mohr's circle to determine the planes on which the maximum shear stress acts. Sketch a properly oriented maximum-shear-stress element and indicate the normal and shear stresses acting on its faces. Ơn nt o, Note: for (b), the angle θ is between 0 and 90° and is positive
Problem 2: A state of plane stress at a point on the surface of a structure consists of the following stress components: Ox = 18 ksi, oy = 24 ksi, and Txy = 15 ksi. Note that the stress components act in the directions shown on the element below. Ox Txy 24 ksi бу 18 ksi 15 ksi (a) Draw a complete Mohr's circle for this stress state. Clearly label the X and Y faces, the center C, and the radius R. (b) Using Mohr's circle, determine the stress components Ox, Oy, and Txy on an element rotated 25° counter-clockwise from the original element shown. Label all of these quantities on the circle. (c) Show all stresses from part (b) on a properly oriented stress element. Be sure to include all stress components acting on the element.
Two forces are applied on the beam shown below. (a) Determine the normal and shear stresses at point B on the shown cross-section. (b) Show the state of stress at the point B on a volume element. 400 lb B 1 in. 2 in. 500 Ib 2 in 10 in. 1.5 in. 1.5 in. Show your steps and highlight the following answers please I =
5 Figure 5 shows a thick cylinder of 50 mm internal radius and 115 mm outer radius is subjected to an internal pressure of 60 MN/m² and an extemal pressure of 30 MN/m?. Determine the hoop and radial stresses at the inside and outside of the cylinder together with the longitudinal stress if the cylinder is assumed to have closed ends using analytical and graphical approaches.