The MDF sheet shown in the figure below iscut by a laser pointer, which moves through the curved groove. Your distance in  meters measured along the slot is given by s = 9t2– 2t, with t in seconds. The laser is at A at time t = 0.2 s and at B when t = 3.0 s. Determine to two decimal places of precision: a) the magnitude of the average acceleration between A and B; b) the average vector acceleration between A and B.

Q: Determine the minimum weight W, of block 2 to stop block 1 sliding down the incline. frictionless pu...

A:

Q: Water flows inside the tube 45mm diameter and 3.5 meters long at a velocity 1m/s. Determine the heat...

A:

Q: At the instant shown, a screw-bar-driven Collar A starts from rest and moves upward with a constant ...

A:

Q: A steam power plant operates on the ideal Rankine cycle producing a net power output of 120 MW. The ...

A: Answer: ◆ The quality of steam entering the condenser is 74.10%. ◆ Qa = 3155.71 kJ/kg , Qr = 1795.96...

Q: 4. Distinguish between tidal and wave energy?

A:

Q: Write a Reaction Paper on this phenomenon." The Impact of the Pandemic to the Career Choice of Stude...

A: Like any other service sector, aviation sector is hit hard by the pandemic. The industry has already...

Q: Objective: (i) Use the superposition method to verify your answer. (ii) Sketch V and M diagram for t...

A: Drawing the free body diagram as shown below, RA=12×L×qoRA=qoL2   At a distance x from the right en...

Q: 3. Calculate the percentage increase in length of a wire of diameter 2.5 mm stretched by a force equ...

A: As per given question  Wire diameter =2.5mm Weight =100 kg Y =12.5×1010N/m2 we have to determine per...

Q: A small turbine runs an aireraft reirigeration system. Air enters the turbine, at 4 bar and 40°C wit...

A: We know that an aircraft's refrigeration system is powered by a tiny turbine.At a pressure of 4 bar ...

Q: Determine the angle of twist caused by a 25kip – in torque T in the 3in diameter solid aluminium sha...

A:

Q: If blocks A and B of mass 10 kg and 6 kg respectively,  are placed on the inclined plane and release...

A: Given   Mass, mA = 10 kg             mB = 6 kg Find   Force developed, F

Q: The wheel rolls without slipping at constant angular velocity o-5 rad/s. At the instance shown, use ...

A:

Q: Heat transfer problem Water flows through a thin-walled cylindrical tube of diameter 1 cm, maintaine...

A:

Q: Read the questions carefully and answer with complete solution and units.Use the steam tables provid...

A: Given Data: Pressure at the inlet of the turbine, P1=10 MPa The temperature at the inlet of the tur...

Q: 4.5-6 The simple beam AB shown in the figure is subjected to a concentrated load P and a clockwise c...

A:

Q: Bending Tool Problem: Sheet metal is to be bended on a pneumatically actuated bending rig. After it ...

A:

Q: 2. For the following rheological model: or ww E2 2 (a) How is the behavior affected by changing E2 w...

A: The rheological properties of fluid are defined on the basis of the newton's law of viscosity  ζ=μdu...

Q: A solid shaft of diameter d = 10 cm (Fig. attached) is subjected to a tensile force P = 10,000 N and...

A: Given    Diameter, d = 100.5 cm       Torque, T = 5000 N.cm                      = 50 N.m         Lo...

Q: Saturated water vapor at 200.111 oC is isothermally condensed to a saturated liquid in a piston-cyli...

A:

Q: The car A has a forward speed of 33.0 km/h and is accelerating at 2.3 m/s2 . Determine (a) a speed a...

A:

Q: value of spring constant K needed

A: Given;Uniform stiff rod of length,l=300 mm having a weight= 300 NIt is pivoted at one end and connec...

Q: Draw a graph showing the ELASTICITY, FLEXIBILITY, and BRITTLENESS property in terms of stress and st...

A: Given Data : ELASTICITY, FLEXIBILITY, and BRITTLENESS

Q: Describe the step-by-step procedure in turning a taper using compound rest method.

A: Inroductiopon to taper turning: Taper turning is the process of to make conic cylinderical surface,...

Q: Question (2) As shown in the Figure below, If the discharge was 0.0035 m/s. Calculate the water leve...

A: Find the level in the water tank. Given data :-  Discharge - 0.0035 m^3/sec.  

Q: A 1018 steel wedge will be created with Sy = 63 Kpsi and a factor of safety of 1.5. The axis where t...

A:

Q: Assuming the reaction of the ground is uniformly dis- tributed, draw the shear and bending-moment di...

A:

Q: What is the relationship between the force pulling the slider up the incline and the coefficient of ...

A: “Since you have asked multiple question, we will solve the first question for you. If you want any s...

Q: A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter...

A: Calculate the polar moment of inertia of the solid steel shaft-Jst=π32D4Where-D=diameter of steelD=2...

Q: Hello could anyone teccomend any improvements to thid type of rankie cycle combustion chamber fuel H...

A:

Q: At the instant shown, a screw-bar-driven Collar A starts from rest and moves upward with a constant ...

A:

Q: 4. For a flat plate, the transition from the free convection boundary layer to the free convection t...

A:

Q: Q1// A heat engine receives 1000 KJ of thermal energy from a heat source. (60%) of the resulting wor...

A:

Q: )A race car starts accelerating at a = 5 and continues to do this for 10 seconds. What is its final ...

A:

Q: nterdisciplinary research takes time to have an impact. What is your opinion for this  statement? Ma...

A: Interdisciplinary research 

Q: A 5.31 horsepower rating No. 40 roller chain has an input through a 12-tooth sprocket turning at 1,8...

A:

Q: Q1. Collar A moves at a velocity, V4, to the right. The values of the kinematic parameters are given...

A:

Q: 1. Ea BHA jt 30.5 Ft Ea DP Stand 93.5 ft TDS + Hook block = 68 K Lbs Depth is 12800 Ft, Mud weight i...

A: a-P(0)=probality that oil is present =0.3P(70)=Probality that oil is not present 1-0.3=0.7P(G)= Prob...

Q: Block A of 7 kg is connected to block B of 3 kg by the pulley system indicated below. Determine the ...

A:

Q: List the type of processes that occurs in a Carnot cycle. How could you design a Carnot engine with ...

A:

Q: explain what are the factors/elements that impact the grading in artistic gymnastics

A:

Q: An air stream, with T1 =0 C, p1= 60.0 kPa (abs), and V = 497 m/sec, undergoes a normal shock. Determ...

A:

Q: The time taken to drill a hole

A: Given; Feed rate of a drill is;   f= 0.25 mm/revAt a rotating speed at, N= 300 rpmWhere, Plate thick...

Q: re below. A hot fluid at temperature To passes throu hematical model that gives the variation of the...

A: given data COPPER     copper k=40W/m°ccross section area , A =1 m2then heat transfer rate through t...

Q: 5. The torques shown are exerted on pulleys A and B. The diameter of the shaft AB is dAB = 50mm whil...

A: To transmit energy by rotation it is necessary to apply a turning force. in the case of a shaft if t...

Q: ented ass shown. Determine the stress at point would the stress be at point A if the couple M is o 2...

A:       find the principal axis ;average moment of inertia ,  corresponding to the point E  substitute...

Q: ermine the weight “W” of the heaviest cylinder that can be supported in the position as shown in the...

A: From above diagram-

Q: 12. A heated channel is operating at 7.5 MPa. Water enters the channel at a rate of 17 kg/s and an i...

A: Given: mass flow rate of waterm˙=17  Kgs At the pressure 7.5 MPa: From the steam table: Saturation t...

Q: Q2) The system shown in Figure 2 is open to 1 atm on the right side. If L = 120 cm, what is the air ...

A:

Q: T;

A: No answer

Q: Use Möhr's circle to solve the unknown values in the stress systems shown in figure 16.37. 80 MPa 30...

A:

Conservation of Energy

In physics, the rule of the conservation of energy states that energy doesn’t disappear from the atmosphere; instead, it changes its form from one type to another. Energy is one of the most important physical quantities in nature, and it cannot be created or destroyed — only transformed.