The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part (b) of the figure below). (Consider only the in-plane stresses - the stresses in the xy-plane). 17,600 psi B LA 6,650 psi A Cross Side |2,700 psi View Section (a) (b) Determine the maximum shear stresses (in psi), associated normal stresses (in psi), and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For maximum shear stress, enter the magnitude. For normal stresses, use t sign convention for stresses acting on inclined sections.) Tmax psi psi 02 psi • counterclockwise from the +x-axis ° counterclockwise from the +x-axis p1 %3D p2

The normal and shear stresses acting on element A are 6,650 psi, 17,600 psi, and 2,700 psi (see part (b) of the figure below). (Consider only the in-plane stresses - the stresses in the xy-plane). 17,600 psi B LA 6,650 psi A Cross Side |2,700 psi View Section (a) (b) Determine the maximum shear stresses (in psi), associated normal stresses (in psi), and angles of the principle planes (in degrees counterclockwise from the +x-axis). (For maximum shear stress, enter the magnitude. For normal stresses, use t sign convention for stresses acting on inclined sections.) Tmax psi psi 02 psi • counterclockwise from the +x-axis ° counterclockwise from the +x-axis p1 %3D p2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1) Figure 1 shows an element with stresses. Angle 1 Oy Tyx Ox Txy Tyx Figure 1 Point Ax-direction stress 60MPA(compression), y-direction stress 40MPA(tension), negative shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1-30°, Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle.
A bar of a uniform cross-section is rigidly fixed at one end and loaded by an off-centre tensile point load F = 1.5 kN at the other end, see Fig. Q1a. The Figure Q1b presents the view of the beam from the free end where the point of application of the load F is indicated as A. The allowable stress [0]=234 MPa The geometrical parameters are given as follow h 18 mm, b=37 mm N y b Figure Q1a Figure Q1b h F X
1) Figure 1 shows an element with stresses. Angle 1 Oy Tyx Txy Tyx Figure 1 Point B- x-direction stress 60MPA(tension), y-direction stress 40MPA(compression), positive shear stress 30MPA a) From basic priciples determine the stresses on the plane of the indicated angle 1. (20°), Show al calculations. Draw the orientation of the stress block for this scenario. b) Repeat question (a) using a Mohr circle.
A tapered cantilever beam AB having rectangular cross sections is subjected to a concentrated load P = 46 lb and a couple Mo = 790 lb - in. acting at the free end [see the figure part (a)). The width b of the beam is constant and equal to 1.0 in., but the height varies linearly from ha = 2.0 in. at the loaded end to hp = 3.0 in. at the support. Use L = 20 in. Мо В hg (a) 3P qo = T Мо (b) ЗР 90 =7 \ Mo.
For the stress block shown, what is OP2 if OP1 = 140 MPa (T)? A.60 MPa (T) 40 MPa B.60 MPa (C) C.20 MPa (C) D.20 MPa (T) Txy Which among the following is ALWAYS TRUE about the maximum in-plane shear stress? A.It acts on planes 450 from principal planes. B.It is equal to the absolute maximum shear stress. C.It is equal to the principal stress with higher magnitude. D.It acts on planes with zero normal stress. 120 MPa
At a point in a component, the state of stress is shown on the element below. Assume that the stress magnitudes are s,-7150 psi and Sy - 4475 psi. The stresses act in the directions indicated in the figuure. Determine the magnitude of the absolute maximum shear stress that acts at the point. Answer: Tmax psi
The state of stress at a point in a structural member may be represented by a two-dimensional stress system in which o, =100 N/mm², o,=-80 N/mm² and 7,, =45 N/mm². Determine the direct stress on a plane inclined at 60° to the positive direction of o, and also the principal stresses. Calculate also the inclination of the principal planes to the plane on which o, acts. Verify your answcrs by a graphical method. Ans. 6,= 16 N/mm², o1 =110.6 N/mm², ơn=-90.6 N/mm², 0= –13.3° and –103.3°. !!
For a square cross-section bar affected by torsional moment at both ends, the stress components are shown as follows (opposite the figure): a) Find the principal directions for the zero principal stress? b) For the following special case, show that the stress vector on the lateral surface of the rod is zero: 4 = (xỉ – a?xx? - a²) %3D c) Also the torsional moment at each of the two ends of the rod is equal to: M = 32 4 = f(x1, X2) ax2 011 = 022= 033 = 012 = 0 X2 221 PM Links 69% 44°F Rain and snow ENG 1/16/2022
Two cylindrical rods AB and BC are welded together at B and loaded as shown. Knowing that the average normal stress must not exceed 175 MPa in rod AB and 150 MPa in rod BC, determine the smallest allowable values of d1 and d2. 300 mm 250 mm A B C -d₁ 40 kN -d₂. 30 kN
The tensile member shown, 60mm x 80mm in cross-section is subjected to a load of 250kN. The plane AA’ makes an angle of 15o with the x-axis. What is the tensile stress of section AA’? Determine the shear stress on plane AA’ At what angle of plane AA’ is the shear maximum.
Question 2. Determine the principal stress, the maximum in-plane shear stress, and average normal stress. Specify the orientation of the element in each case. 20 MPa 80 MPa 30 MPa
Q/Normal and shear stresses acting at the point is shown in Figure 1- Determine the principal stresses and the maximum shear stress acting at the point . Show these stresses in an appropriate sketch . 2- If the element is rotated 30 deg clockwise then determine the normal stresses and the shear stress acting at the point . Show these stresses in an appropriate sketch .