The piston rod of diameter 30mm and length 800mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200GPa. Calculate its factor of safety for the piston rod?

The piston rod of diameter 30mm and length 800mm in a hydraulic cylinder is subjected to a compressive force of 10 kN due to the internal pressure. The end conditions for the rod may be assumed as guided at the piston end and hinged at the other end. The Young's modulus is 200GPa. Calculate its factor of safety for the piston rod?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the position shown for the log hoist, booms ACDF and EFG are perpendicular and EFG is parallel to AB. What is the maximum weight (in Ib) of the log if hydraulic cylinders BC and support a maximum of 4123 Ib and 9123 Ib, respectively? Note that BC is a duplicate cylinder. (Hint: Recall multiple failure criteria.) E DE can 12' 10 This is nor your own propèrty so do ngi uwe at n ghi way as if it were your own. Legend: '- foot “- inch A 45° B This is not were your e ownprop 12" o do not use it in way as 12" 24"
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 42 45 100 Ib 18 3 ft 3 ft- 30 200 Ib ft 30" 30 30 kg 2 ft B B Fig (1) Fig (2) Fig (3)
Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position shown compute the magnitude of the force supported by the pin at Cand the oil pressure pagainst the 3.20 in-diameter piston of the hydraulic-cylinder unit AB. See figure (3). 45 100 Ib te-18 15 3 ft 3 ft- 30 200 lb ft 30 30 30 kg 2 ft B 12 Fig (1) Fig (2) Fig (3)
For the same question, the M25 Screw will be used when pressing the Nut Wheel onto the shaft. Assuming that the force that the nut needs to suppress is Fçak=1218 kgf (it was found in the previous question, but we don't use it), what should the minimum NUT HEIGHT be in mm to create this force safely? (Screw and Nut's surface safety pressure Pem=45 N/mm2 Screw base diameter d1= 21.5 mm. (Calculate the pitch (h=?) according to the given ones, considering that metric screw is used!)
Find the clamping force on the smooth pipe B. Draw all necessary FBDs for this problem. Fully show your solution, equations, all your work.
The Cylinder weighs 1000 kg, rest on an plane which is inclined at 34° from the horizontal. The normal force acting on a plane to the cylinder is 10 KN. Assume smooth surface, the cylinder leaned to a vertical rod of 8m long and has a weight of 5 KN which was supported by a cable and a hinged (as shown). Find the tensile force of the cable holding the rod and the reactions of hinged to support the cylinder from sliding.
The outside diameter of the coils of a safety valve spring is 120 mm while its wire diameter is 15 mm. This spring, having 10 active coils has the ends in plain ground, and has a free length of 200 mm. 1. Determine the length (in mm) at which this spring must be initially compressed to hold a pressure of 1400 kPa applied on a 32-mm diameter valve seat. Use a modulus of rigidity of 80 GPa. 2. calculate the spring’s maximum stress induced if it is compressed to its solid length
Bearing stress 2. Please provide proper discussion and illustration also complete solution and clear solution please thank you. Determine the length of a square key to be used for a 3.73 kW 1800 rpm electric motor. Motor shaft diameter is 35 mm and the height of the key is approximately one-half of the shaft size. The bearing stress on the key is?
with free body diagram and complete solutions
Calculate the forces, in Newtons, for the following:(d) member FG(e) pin H(f) hydraulic cylinder AB
The bar is 10m long. A mass of 40kg places at 9m from left end of bar. Where should a 60kg mass be placed to balance the bar?
Need help. Please solve this and clearly state how you got your numbers and what formulas you used to solve it. Please make sure you find all the 6 unknows please. Knowing the beta equals 30° and the solid plate weigh 100 kg. What is the cable tension T and the reaction forces at the two bearings? Assume bearing A is a thrust bearing but bearing B is notplease solve for the X component at bearing B. Again please also make you find all the 6 unknows please. And clearly indicate which is which. And please label and make sure to put units