The plan of a flexible circular loaded area is resisting the uniformly distributed load (q), 835 kN/m2 with the radius of 5.7 m. Illustrate and calculate the increase in the vertical stress (Δσ) at a depth of z = 7.2 m below point A which is immediately below the center.

The plan of a flexible circular loaded area is resisting the uniformly distributed load (q), 835 kN/m2 with the radius of 5.7 m. Illustrate and calculate the increase in the vertical stress (Δσ) at a depth of z = 7.2 m below point A which is immediately below the center.

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.13P: Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below...

See similar textbooks

Related questions

Q: The soil is having a saturated unit weight 18.0 kN/m and dry unit weight of 11 kN/m. The water table…

A: Saturated unit weight of soil = 18KN/m3 Dry unit weight of soil = 11KN/m3 Given two diagrams in Fig…

Q: subject - geotechnical design book - principle of foundation engineering

A: We have the following formula for vertical stress:

Q: Practice Problem: Refer to Figure 3.70, a flexible square area is subjected to a uniformly…

A: Given: The distributed load (q) is 100 kN/m2. The depth is 4 m. Consider the figure,

Q: 1. Determine the increase in vertical stress at a depth of 7 m below the point B. Point loads of…

A: using boussenique's equationσ=QZ232π11+rz25/2z=7 mr1=3 mr2=5 m

Q: Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure P6.2).…

A: Applying Boussinesq's Equation: ∆σz=3P2πz21+rz25/2 ...(1)

Q: A flexible circular area of radius 3.3 m. is uniformly loaded by q = 315 kN/m². Determine the…

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

Q: Point loads of magnitude 9, 18, and 27 kN act at A, B, and C, respectively (Figure 8.23). Determine…

A: Boussinesq’s formula for calculating stress below point load:

Q: A uniformly distributed line load is acting on the ground surface. Based on the Boussinesq's theory,…

Q: 1. A soil has the following profile and a lateral stress coefficient at rest is 0.45. 0-4 G, = 2.75…

A: Given K0 = 0.45 Take Unit weight of water = 10Kn/m3 Water table is at 5m below the ground…

Q: A flexible rectangular area is subjected to a uniformly distributed load of q = 225 kN/m?. Determine…

A: Point A q=225 kN/m2B=4 m L=8 mz=3 mm=Bz=43=1.33n=Lz=83=2.67 From Table,…

Q: An embankment load on a silty clay soil layer as shown below. Determine the stress increase under…

Q: Using equation 6.14, determine the vertical stress (Aoz) increase below the center of paded area at…

A: Given Area = 6.35*3.35m^2 Depth 2m,4,6,8,10m q= 225kn/m^2 Calculate stress at different different…

Q: Problem 3.7 For the seepage situations shown in Figure, determine the effective normal stress on…

A: Solution1By considering pore water pressure::σ'=σ-uσ=20×2+3×9.81=69.43KPau=1+39.81=39.24σ'=30.2kpaBy…

Q: C 6 m B A 5 m 3 m 6 m 3 m Fiq 23 - Prob 23

Q: 5. Consider the embankment profile shown below. Determine the stress increase at points A and B.…

A: As both points A and B are at same depth hence the increase in stress level will be same as the…

Q: Problem (4.4): Given: q= 100 kN/m. Find: The vertical stress o, at points 0, 1, and 2 shown in Fig.…

A: Uniformly Loaded Line of Finite Length Case: Consider the free body diagram of given loading on soil…

Q: A 5 m-thick clay (Gs = 2.65, water content = 0.28) is overlain by a 4.50m-thick layer of sand (Gs =…

Q: Using equation 10.35, determine the vertical stress (Aoz) increase below the center of the loaded…

A: The given data is shown below: z=2,4,6,8 and 10m

Q: The water table is located at a depth of 3.0 m below the ground surface in a deposit of sand 11.0 m…

A: Given: The depth of the water table below the ground surface is 3 m. The thickness of the ground…

Q: 2m Dry zone Soil properties: Gs = 2.68 A e = 0.85 В 1.8 m Saturation zone (capillary rise) 0.9 m D…

A: The soil properties are given Specific gravity of solids, Gs = 2.68 Void ratio, e =0.85 The total…

Q: A soil with a unit weight of 18 kN/m3 is loaded on the ground surface by a uniformly distributed…

Q: Consider a circularly loaded flexible area on the ground surface. Given: radius of the circular…

A: The increased in stress under the soil is happen by lots of situation like excess load over the…

Q: A point load of 700 kN is applied on the surface of thick layer of saturated clay. Using…

Q: A 5 m-thick clay (Gs = 2.65, water content = 0.28) is overlain by a 4.50m-thick layer of sand (Gs =…

Q: P2039 kg/m 10 m 15 m P- 1888 kg/m Saturated clay L Sand

A: Given data Depths Water level Saturated densities Sand Saturated clay

Q: Н.О 4 Point loads of magnitude 100, 200, and 400 kN act at B, C, and D, respectively (Figure below).…

A: The given data is: Load at point B (QB) = 100 kN Load at point C (QC) = 200 kN Load at point D (QD)…

Q: 2. Soil with a unit weight of 16.50 kN/m³ is loaded on the ground surface by a uniformly distributed…

A: Determine (a) the vertical stress increment due to the uniform load, (b) the total vertical…

Q: A 5 m-thick clay (Gs = 2.65, water content = 0.28) is overlain by a 4.50m-thick layer of sand (Gs =…

Q: Q2/ Determine the variation of total and effective stresses and pore water pressure with depth for…

Q: Refer to Figure 10.47. A flexible rectangular area is subjected to a uniformly distributed load of q…

A: Given data, q = 330 kN/m2 z = 6 m L = 18 m B = 9 m Influence values are obtained from the given…

Q: 1 A point load of 2000 KN is acting at the surface of a thick clay stratum. Compute the vertical…

A: Solution From boussinesq's equation, σz = IbQz2 Ib = 32π1+rz252 Substituting, z= 1m to 10 m and r=…

Q: Layer No. Thickness, H Soil Parameters e = 0.52, Gs = 2.62 e = 0.56, Gs = 2.65 w = 20%, e = 0.51 1…

Q: Q.3) Determine the increase in vertical stress at a depth 4 m below point A due to surface loads…

Q: H.Q 5 Figure below shows an embankment load on a silty clay soil layer. Determine the stress…

Q: Figure below shows an embankment load on a silty clay soil layer. Determine the stress increase at…

Q: 10.15 For the embankment shown in Figure 10.45, determine the vertical stress increases at points A,…

A: - Total load of embankment per meter length is, Length of base = 10+(22.5*2.25*2)=111.25 m Q=Unit…

Q: Consider a circularly loaded flexible area on the ground surface. Given that the radius of the…

A: This problem is related to vertical stress topic from Soil Mechanics. In this problem there are…

Q: 4. The plan of a flexible rectangular loaded area is shown in the figure below. The uniformly…

Q: Refer to the figure. For a linearly increasing vertical loading on an infinite strip, given: B = 4…

A: Linearly Increasing Vertical Loading : A linearly increasing vertical loading starting from zero at…

Q: e soil profile in the figure below. Given H= 4m and H2=3m; lculate the total stress, pore water…

Q: The plan of a flexible rectangular loaded area is shown in Figure 6.30. The uniformly distributed…

A: Solution: The equation for determining the increase in stress on a flexible rectangular area at a…

Q: 1. Given a concentrated load of 200,000 lbs, find the vertical stress (p) at a depth of 15 ft and 10…

A: As per our guidelines we are supposed to answer only one question. Kindly repost the other questions…

Q: Problem 1: Point loads of magnitude 100, 200, and 400 kN act at A, B, and C, respectively. Determine…

Q: 5-9 Plot the distribution of vertical stress increase (Aoz) at a depth of 2 m below grouiu surface…

A: Given data Point load Depth To find Results given by two theories

Q: A vertical load of 260 kN is applied to a 1.2 m * 1.2 m area at the ground surface that islevel.…

A: Given: The load is 260 kN. The area of the surface is 1.2 m x 1.2 m. The depth is 1.5 m.

Q: Soil with a unit weight of 16.97 kN/m^3 is loaded on the ground surface by a uniformly distributed…

A: Given:- q=300 KN/m2r=d2=42=2 mz=5 m

Q: Calculate the effective stress at A. 25 m Sand and- Gravel Water Table Unit Weight (y) = 20.72 kN/m?…

A: Following is the given soil profile:

Q: The plan of a flexible rectangular loaded area is shown in Figure below. The uniformly distributed…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

The plan of a flexible circular loaded area is resisting the uniformly distributed load
(q), 835 kN/m2 with the radius of 5.7 m. Illustrate and calculate the increase in the
vertical stress (Δσ) at a depth of z = 7.2 m below point A which is immediately below
the center.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 10.12 for q = 700 kN/m2, B = 8 m, and z = 4 m. In this case, point A is located below the centerline under the strip load. 10.12 Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
Referring to Figure Q2 (a), the vertical stress increase at point A is 25 kN/m2due to application of line loads q1 and q2. Determine the magnitude of q2.
Prob. 3 The plan of a flexible rectangular loaded area is shown in Figure below. The uniformly distributed load on the flexible area, q, is 100 kN/m². Determine the increase in the vertical stress, Aoz, at a depth of z = 2 m below a. Point A b. Point B c. Point C 4 m 1.6 m 2 m 0.8 m q = 100 kN/m² A 1.2 m-
An electric power transmission pole is 12 m above ground level and embedded 2 m into the ground. The butt diameter is 450 mm and the tip diameter (the top of the pole) is 320 mm. The weight of the pole, cross arms, and wires is 33 kN. Assuming the pole transmits the load as a point load, find the change in vertical stress in kPa at 2 m depth.
Refer to Figure 10.40. Determine the vertical stress increase, Aoz, at point A with the following values: q1 = 90 kN/m; q2 = 325 kN/m; x1 = 4 m; x2 = 2.5 m; z = 3 m Line kad - Line load -
A concentrated load of 1650 kN rests on the ground surface at coordinates (0,0,0). Determine the net stress increase at the following points: a. Point A - directly below the point load at a depth of 5m b. Point B - at coordinates (3,4,5) Use Boussinesq and Westergaard Analysis. (31.51, 21.12) (5.57, 3.3)
refer to the figure due to application of line load q1 and q2 . the vertical stress increase at point a is 42 kn/m2 determine the magnitude of q
Using Boussinesq’s Equation determine the vertical stress increase ΔϬz, at point C at a depth 3.0 meters , if the point loads at A,B and D are 200 KN, 400KN and 600KN respectively. ΔϬzC =_____________KN/m2.
A concentrated load of 1000 kN is applied at the ground surface. Compute the vertical stress at a depth of 4 m below the load. Use Boussinesq's equation.equation. Select one: O a. 57.75 kN/m2 Ob. 17 kN/m2 Oc. 67 kN/m2 O d. 30 kN/m2
The vertical surface stress is 100 kPa. The stress increase (kPa) at A is 2m 100 kPa 2m 2m A B 1m 7.3 O 12.0 19.3 Use the approximate method to estimate the stress (kPa) under the center of a rectangular loaded area 2 m X 3 m at a .depth of 2 m, if the vertical load is 20 kN 1.67 O 1 O 2 O
100 kN point load and 40 kN/m line load are applied on the ground surface as shown. Compute the variation of the vertical stress increment at the depth z = 5 m directly underneath line AB. Plot the results from Points A to B. 100 kN point load 40 kN/m line load - 5 m 10 m 5 m (Plane view)
The circular flexible area uniformly loaded (q=320KN/m^2). Determine the change in vertical stress: (a) at point A. (b) at a point 2m below point A