The potential transformer used for in power substation To protect power system from surges To protect power system from high potentials To lower system voltage so the measuring and protecting equipment can deal with To raise system voltage so the measuring and protecting can equipment deal with 0 أخری: A process leads to lowering the number of free electrons Excitation Electron attachment Electron detachment Photo-ionization أخری

The potential transformer used for in power substation To protect power system from surges To protect power system from high potentials To lower system voltage so the measuring and protecting equipment can deal with To raise system voltage so the measuring and protecting can equipment deal with 0 أخری: A process leads to lowering the number of free electrons Excitation Electron attachment Electron detachment Photo-ionization أخری

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter13: Transmission Lines: Transient Operation

Section: Chapter Questions

Problem 13.24P

See similar textbooks

Similar questions

Voltage control method connected across the load, to supply part of VAR required is ..... O Shunt capacitor O tap changing transformer O series capacitor O booster transformer
(5) Primary AC Source Transformer Secondary AC/DC Full-wave Rectifier Capaictor in Non- linear Load Figure 6 Analyse different methods of harmonics mitigation to eliminate the harmonic, which you have identify in above power system circuit. You can use harmonic filters, K or equivalent transformers or oversized neutral method depending upon the harmonic sources.
it is usually composed of large capacity circuit breaker that serves as a bridge between the source and the load. A. Switchgear B. Bunduct C. Transformer D. Capacitor Bank
Identify the power system component represented by the given symbol. BE O potential transformer O Circuit breaker O Lightning arrester O current transformer
56. A single phase thyristor adjust line spacing converter with a resistive load is shown below: V₂ = V sinest SCR ER R V₂ (B) 1.11 (D) 1.44 If the supply voltage is 230V (rms) at 50 Hz, calculate ripple factor for firing angle a-45" and R - 100 9. (A) I (C) 1.21
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
please answer 4 four questions correctly and no need to write your explnation just final answer 1. The various types of errors in dynamometer wattmeters are A./Error due to Eddy currents B./Error due to pressure coil inductance C./All of above D./Error due to pressure coil capacitance E./Error due to friction 2.The primary winding of a potential transformer has A./no turns B/a larger number of turns C/a few turns only D/intermediate number of turns 3. The current transformer (CT) and potential transformer (PT) are used for A.measuring low current and voltages B.measuring high resistances and frequencies C.measuring very low current and voltages D.measuring high currents and voltages 4. The secondary winding of a potential transformer has A/ no turns B.intermediate number of turns C.a few turns only D.a large number of turns
Given three phase fullwave with center tapped transformer with 220 Vac source voltage, determine: Vdc, Vrms, Pdc, RF, and efficiency. D1 L1 D2 L1 L7 D3 220 Vac, 60 Hz Vo D4 RL=10 ohms L2 D5 L3 D6 m. L6 3 F12 87
What is the relationship between primary induced emf( E1) and applied voltage (V1) of a Transformer? O a. Both are unequal and in phase O b. Both are unequal and 180 degree out of phase O c. Both are equal and 180 degree out of phase O d. Both are equal and inphase
Transformer 1) Enumerate the way/s by which the voltage of the large coil may be: a) increased (AC source) b) reduced to zero (AC source) c) increased (DC source) d) reduced to zero (DC source)
A 100VA single-phase transformer inside a refrigerator has 100 turns in its primary coil and 20 turns in its secondary. A 120v ac source is connected to the primary. a. Is this an example of a step-up or a step-down transformer? b. What is the secondary voltage? c. Indicate why a transformer is needed in a fridge – why two different voltages are needed in a fridge, and indicate a part of the fridge that is powered by the secondary voltage of this transformer. d. Ifa 202 load is connected to the secondary, what percentage of its rated will the transformer supply? e. If the primary is reduced to 90 turns, what will the secondary voltage be with the same 120v primary source? power
90KVA, 460/230 3Phase transformer, Determine the Primary Conductor Size (include the AWG size number), Secondary Conductor Size (include the AWG size number), Primary Protection Breaker, and Secondary Protection Breaker. uarn