The shown beam cross-section has f' 4,000 psi and f, 60,000 psi. Determine the depth of th neutral axis "c" (distance from the extreme concrete compression fiber to the neutral axis) %3D 12" 15" As (total) =5.06 in2 18" O 5.836" O 6.543" O 7.567" O 3.683" O 4.872"

The shown beam cross-section has f' 4,000 psi and f, 60,000 psi. Determine the depth of th neutral axis "c" (distance from the extreme concrete compression fiber to the neutral axis) %3D 12" 15" As (total) =5.06 in2 18" O 5.836" O 6.543" O 7.567" O 3.683" O 4.872"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Help me how to design the REINFORCED CONCRETE BEAMS WITH IRREGULAR CROSS SECTION as shown infigure 1 using the following parameters:F’c = 3,500 Psi Fy=Grade 40 Stirrups = Φ10mmMu = 200 Kn-M All Concrete cover = 30mm Es=200,000 Mpa Find the following: AC area of compression concrete stress block in mm. Assume z = 0.85dEff a height of compression concrete stress block in mm. c distance from the neutral axis to outermost compression fiber in mm. z actual moment arm for Mu=ØTz in mm. As actual area of tension steel in sq.mm. N quantity of Ø20mm steel rebars ЄS Actual Strain of steel ЄY Yield Strain of steel Check if the beam is singly reinforced concrete in the designed then concludeCheck: ЄY < = > ЄS Draw the Working Drawings of the x-section.
Situation C: A rectangular beam has a concrete strength of 24 MPa. The yield strength of the reinforcing bars is 300 MPa. Width of the beam = 350 mm. %3D 65 mm 2 - 25 mm e 435 mm 5 - 36 mm e 350 mm 7. What is the depth of compression block in mm?
SITUATION A: A T beam has a property shown below. fy = 420 MPa, f'c = 35 MPa %3D %3D and Es =200,000 MPa effective width = 1200 mm 100 тm 550 mm 450 mm (3060 mm²) 300 тm 2. What is the distance of the neutral axis from the extreme compression concrete in mm?
[Situation 6] The inverted T-beam shown is post - tensioned with cables having a total area of 14 sq.cm placed at 15cm above the bottom flange. The dimensions of the beam having a span of 14m is shown on the sketch. The beam is subjected to an initial prestress of 9600 kg/sq.cm. Assume a loss of stress of 16% and an allowable compressive stress in concrete of 150 kg/sq.cm and tensile stress of 8 kg/sq.cm. Determine the bottom fiber stress due to the prestressing force. O -10.5 MPa O -11 MPa O -12 MPa O -12.5 MPa
Load = 3000 lb Q:Find Stresses at: Section A-B & Section D-C "18.0"- "5,5" Plain Concrete: D Compressive Strength : 280 (Psi) "12.0"- "0.5"-
A cross section of a prestressed bonded beam is reinforced by prestressing tendons having a total area of 925 sq.mm. Specified yield strength of prestressing tendon is 1610.75MPa. Specified tensile strength of prestressing tendon is 1895MPa. And specified compressive strength of concrete of 34.6 MPa. The beam has a width of 300mm and a total depth of 600mm. Distance from the extreme compression fiber to the centroid of prestressing tendon is 490 mm, Pi=1387.5 KN , R=0.8 and Eps=196 GPa. If the given section, is provided with additional tension reinforcement, As = 3D25mm with specified yield strength of 415MPa, and with centroid located 75mm above the bottom of the beam, 1. Would the code equation be applicable. 2. What should be the value of Xp in the code equation used to evaluat fps? 3. What is the stress in the prestressed reinforcement at nominal strength, fps, using the code equation.
H.W.4: Determine the design moment strength of a rectangular concrete section reinforced with four no. 9 bars in one row. Given : b 305 mm, d= 419 mm, total depth h= 483 mm, and reinforced with three no. 9 bars, fy = 414 MPa and f. 27.58 MPa. %3D 3 #9 250 mm 520 mm 457 mm
313 اعرخ 250 17 ample(4)For the beam section shown figrese, assume:- Ae= 28 MPa , fy= 420 MPa., EsIE=S 650 fr = modulus of ruptureso.62VFé 600 (Effective depth) %3D %3D Determine the max. stresses in Tension Concréte and in steel reinforcement if the applied 3 25 Ast = 1530 mm Fig.(4) B.M= 61 kN:m at this section. solution: The actual in f2504 Beams
For the figure shown. Design the upper leftmost corner slab. The dead load pressure is 5.19kpa and live load pressure is 2.40kpa. use fc'=21mpa, fy=345mpa. the beam has dimension of 300mm by 500mm. use 10mm main bars. Clear concrete covering = 20mm. Round off the slab thickness to the nearest whole number divisible by 5. As = mm2 cm 2.8m 2.8m 2.8m m K C F
A rectangular reinforced concrete beam has a width of 300 mm andan effective depth of 450 mm to centroid of the tension bars. Thebeam is reinforced with six 32 mm ɸ tension bars placed in twolayers with the outer layer having a depth of 478 mm, and two 28mm ɸ compression bars with centroid 65 mm from the extreme concretefiber. Use the 2010 NSCP, fc’= 34.5 MPa and fy = 345 MPa. Assumethat the concrete displaced by the compression steel shall not beneglected and that the compression steel yields. Det. the following:19. The balanced steel ratio if the beam is singly reinforced. a. 0.04607 b. 0.03555c. 0.02721 d. 0.03672 20. The maximum steel ratio for a singly-reinforced section intension control. a. 0.03555 b. 0.04607c. 0.03672 d. 0.02721 21. The maximum steel ratio for a doubly-reinforced section intension control. a. 0.02721 b. 0.03672c. 0.03555 d. 0.04607
hinz 1. For the beam cross section below, determine the amount of steel As required to cause the strain in the tension steel & to be 0.005 just as the maximum strain in the concrete reaches 0.003. fc' = 3000 psi and fy = 60,000 psi. N.A. b= 10"- Cross Section d = 23" [7422 4233 134 S THE THE CALE DES 2 23-c me Like phans 0.005 PANE Strain 0.003 P HOME st 0.85f Stress 6 I.C. Nc NT * * * * * Delorme
Give full explanation Awall form 14 ft high is filled with 160 lb per cu ft concrete at a tem perature of 70°F. The concrete is Type I without a retarder. Concrete will be placed with normal internal vibration to a depth of less than 4 ft. The rate of placement is 5 ft per hr. From Table 1, the value of Cw is 1.1 and from Table 2 the value of Cc is 1.0. The rate of placement is less than 7 ft per hr and the place ment height does not exceed 14 ft so calculate the lateral pressure by using appropriate formula.