The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, 0-28°,0-55 deg/s, and 0 - 10 deg/s². Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.5-kg slider B. Neglect all friction, and let L-0.75 m. The motion occurs in a vertical plane.

The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, 0-28°,0-55 deg/s, and 0 - 10 deg/s². Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.5-kg slider B. Neglect all friction, and let L-0.75 m. The motion occurs in a vertical plane.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The electric motor is used to pull a train at a maximum constant speed of 60 km/h. This motor has a power of 340 kW. The train is pulled directly up the inclination of 1 in 180. The tractive resistance against the motion is 80 N.1.Draw the free body diagram representing all forces acting on the train2.Calculate the mass of the train.
In the system shown, the mass at A is 10 kg and that at B is 5 kg. The mass-moment of inertia of the pulley about point C is 8 kg.m2. At the instant shown, mass A is moving downwards at 5.3 m/s. Find the total kinetic energy of the system. Neglect friction. Write your answer in Joules but do not write the units. 0.15 m B 0.1 m A Answer: Tavlor Te a mn
If there is n friction in the system, the Lagrange's equation will be based only on kinetic energy and protentional energy only. Select one: O True O False III O
A brake test for an automobile is conducted. During the brake test, the automobile of mass 1800 kg (including driver) is travelling at the speed of 110 km/hr as it passes point A, and the car descends a hill of 1in 2 (Sine). The driver applies brakes so as to bring the car speed at B to 50 km/hr. The total frictional resistance to motion is 235 N. Using Work-Energy Method, Calculate the following required to bring the car to 50 km/hr from 110 km/hr in 210 m (From Point A to Point B) B Determine the Value of Total Energy about Point A TE= Determine the Value of Total Energy about Point B TEb= Determine the Value of Breaking Force needed Fb= N A
The rate of the rotating arm is 4 rad/s when it is 3 rad/s² and 0 = 180°. Determine the force it must exert on the 0.45 kg smooth cylinder if it is confined to move along the slotted path. Motion occurs in the horizontal plane. Round your answer to 2 decimal places. 6 = 4 rad/s, 0 = 3 rad/s²/ r 0 = 180° r = (²7) m
If the 100-kg mass has a downward velocity of 0.5 m/s as it passes through its equilibrium position, calculate the magnitude amax of its maximum acceleration. Each of the two springs has a stiffness k = 180 kN/m. Ans. amax = 30 m/s2 %3D k k 100 kg
A truck of mass 6 tonnes was moving with a velocity of 145 km/hr. The brakes were applied to bring the truck to 40 km/hr in 750 m. Determine the uniform force exerted by the brakes. Also find the velocity it will reach if the same force is applied in the same direction for 8 seconds and also find the distance travelled in this period. The uniform force exerted by the brakes in N is The velocity it will reach if the same force is applied in the same direction for 8 seconds in m/s is The distance travelled if the same force is applied in the same direction in this period in m is
The constant tensions of 200N and 160 N are ap- Q2 plied to the hoisting cable as shown. If the velocity v of the load is 2 m/s down and the angular velocity w of the pulley is 8 rad/s counterclockwise at time t = 0, determine v and w after the cable tensions have been applied for 5 s. Note the independence of the results. 200 N 160 N 300 mm 15 kg k = 250 mm 20 kg
The helical path is wound around the circular cylinder with radiusR . The step h= 2*pi*R. The object A is sliding through the path guide under gravity (acting in the negative zdirection). There is no air resistance 1)Draw the force diagrams in (theta ,Z ) plane (tangent to the cylinder) and in( r,theta ) plane. 2) If the initial speed is 0, find the speed after 3 full circles. Given: R, g, m, u.[Hint: Use the work-energy principle.]
A block slides on a rough horizontal surface from point A to point B. A force (magnitude P= 2.0 N) acts on the block between A and B, as shown. If the kinetic energies of the block at A and B are 5.0J and 4.0 J. respectively and the work done on the block by the foree of friction as the block moves from A to B is -4.5 J what is the distance between poini A and B
The lower block of mass m2 = 3.2 kg is pulled on by a rope with a tension force of 28 N. The upper block has mass m1 = 1.8 kg. The coefficient of kinetic friction between the lower block and the surface is 0.32. The coefficient of kinetic friction between the lower block and the upper block is also 0.32. What is the acceleration of the 3.2 kg block?
The slotted arm OA rotates about a fixed axis through O. At the instant under consideration, 0 = 35%, 0 = 39 deg/s, and Ö = 15 deg/s². Determine the magnited of the force F applied by arm OA and the magnitude of the force N applied by the sides of the slot to the 0.2- kg slider B. Neglect all friction, and let L = 0.68 m. The motion occurs in a vertical plane. 0 -L B m