The smooth pin P has a mass of 80 g. It is attached to an elastic cord extending from O to P and, due to the slotted arm guide, moves along the horizontal circular path r = (0.8 sin 0) m. If the cord has a stiffness k = 30 kN/m and an unstretched length of 0.25 m, determine the force of the guide and the normal force of the circular path on the pin when 0 = 60°. The guide has a constant angular velocity è = 5 rad/s. 0 P ė = 5 rad/s

The smooth pin P has a mass of 80 g. It is attached to an elastic cord extending from O to P and, due to the slotted arm guide, moves along the horizontal circular path r = (0.8 sin 0) m. If the cord has a stiffness k = 30 kN/m and an unstretched length of 0.25 m, determine the force of the guide and the normal force of the circular path on the pin when 0 = 60°. The guide has a constant angular velocity è = 5 rad/s. 0 P ė = 5 rad/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. If the 100-N pull is then removed, find the distance the block will travel.
The 250-N block rests upon a level plane for which fk = 0.2. It is pulled by force P = 100N inclined at 20o with the horizontal. If the 100-N pull is then removed, find the distance the block will travel. the answer must 3 decimal places.
The spring has a stiffness of 830 N/m and is undisturbed and measures 400 mm. Determine the forces on the BC and BD cables when the spring is stretched in the position shown in the figure.
4. A vertical force F is applied to the cord that wraps over a pipe with a cylinder support by the cord passing over the pipe 6 times. Determine the largest weight and mass of the cylinder where the cylinder will not move with F = 200 N. Take us= 0.25.
The post weighs 8 kN>m. Determine the internal normal force in the post as a function of x.
The winch takes in cable at the constant rate of 105 mm/s. If the cylinder mass is 105 kg, determine the tension in cable 1. Neglect all friction. 2 1 105 kg
2. Find the horizontal force P to start the motion of any part of the system of three blocks resting upon one another as shown. The weight of the blocks are W-300 KN, Ws= 100 KN and Wc =200 KN. Between A and B μ=0.30, between C and B, μ =0.20 and between C and the ground, p=0.10. 1 sni brod nog 02.0-4 B C 05.0-4 Solution: tamos quoy worla bre sosia asquar 005 300 en of jells400 N₁-300 F3 N-300- N₂=300 Assuming B and C will not move. F₁ = 300 (0.30) F₁ = 90 kN ne à bns A zelboß 1 P = 90 kN es ensla berb hebnu 02.0- y elin 05.0= q V in Celpris orllanimetsa MX 008 Assuming C will not move: al 1st F2=400 (0.20) = 80 kN OTE Bm ribirte F₂ vica Assuming the three blocks move: F3 = 0.10 (600) F3 = 60 kN P=60 KN Least force is 60 kN.
if the basket at E weighs 3.5 N, determine the weight if crate f and the unstretched length of the spring (k= 12 N/m)
3-18. If the spring DB has an unstretched length of 2 m, determine the stiffness of the spring to hold the 40-kg crate in the position shown. 3-19. Determine the unstretched length of DB to hold the 40-kg crate in the position shown. Take k = 180 N/m. %3D -2 m- 3 m В 2 m www A
2. The backhoe supports a 7.5 kN weight of soil in the bucket which has a center of gravity at G. Find: 0.64 m 0.25 m ● 0.26 m 0.3 m 1.68 m Force in cylinder ED (indicate if force is in tension or compression) Force in cylinder FI (indicate if force is in tension or compression) OF 0.4 m 0.1 m A -1.44 m- 17.5 kN 0.25 m D B m E 0.22 m 0.45m H O SUSIS Force in ED = Force in FI = KN (Tor C) kN (Tor C)
The homogeneous box has mass m. The magnitude of force P is slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. A B Answer: P = 32° P 1.5 d C mg μs = 0.43
The pipe is stuck in the ground so that when it is pulled upward the frictional force along its length varies linearly from zero at B to fmax (force/length) at C. The pipe has a length L, cross-sectional area A, and the material from which it is made has a modulus of elasticity E. Determine the initial force P required to pull the pipe out. Express your answer as an expression in terms of the variables f, L, A and E and any necessary constants.