The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c ). If the allowable shear stress of the shaft is 88kPa (i) Determine the maximum torque T that can be transmitted by the shaft. (ii) What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? (iii) Sketch the shear-stress distribution along a radial line in each case.

The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c ). If the allowable shear stress of the shaft is 88kPa (i) Determine the maximum torque T that can be transmitted by the shaft. (ii) What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? (iii) Sketch the shear-stress distribution along a radial line in each case.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Similar questions

A shaft required to transmit 50kW of power will be running at 100rev/min. The maximum twist in 3m length of the shaft is limited to 1.5 degree. If the maximum torque is 30 percent more than mean or average torque. Assume entirely elastic action and take modulus of rigidity for the shaft material G = 135 GN/?2. Determine the following:a. Diameter of the shaft.b. Maximum shear stress developed in the shaft. I need answer ASAP. Thank you!
À solid 0.96-in.diameter shaft is subjected to the torques shown. The bearings shown allow the shaft to turn freely. Determine the shear stress magnitude in shaft (1). 10 Ib-A 50 Ib-ft 70 Ib-ft (1) (2) 30 Ib-f (3) 827 psi O 880 psi O 956 psi 691 psi O 739 psi
The steel shaft of a socket wrench has adiameter of 8.0 mm and a length of 200 mm (seefigure).If the allowable stress in shear is 60 MPa, whatis the maximum permissible torque Tmax that may beexerted with the wrench?Through what angle f (in degrees) will the shafttwist under the action of the maximum torque?(Assume G = 78 GPa and disregard any bending ofthe shaft.)
A shaft is made of a steel alloy having an allowable shear stress of Tallow = 12ksi. IF the diameter of the shaft is 1.5 inches diameter the maximum torque T if a 1in, diameter hole is bored through the shaft? Sketch the shear stress distribution along a trial line in each case.
Q2/ A hollow shaft has to transmit 6MW at 150rev/min. The maximum allowable stress is not to exceed 60 MN/m? nor the angle of twist 0.3° per meter length of shafting. If the outside diameter of the shaft is 300 mm find the minimum thickness of the hollow shaft to satisfy the above conditions. G = 80 GN/m2
A solid 1.750-in.-diameter steel [G= 13,000 ksi] shaft is subjected to torques TB = 265 lb-ft and TD 90 lb-ft, acting in the directions shown. Assume a = 48 in., b = 72 in., and c = 36 in. If the allowable shear stress in the shaft is 16 ksi, determine the maximum torque Tc that can be applied to the shaft. (1) Answer: Tc i B (2) b Tc (3) Tp lb-ft D
An automobile engine develops a maximum torque of 162Nm. The low gear ratio of transmission is 2.75, while the back axle ratio is 4.25. The effective wheels radius is 0.325m and the co-efficient of friction between the tyre and the road surface is 0.6. If the permissible shear stress is 32373 X 104Pa. Determine the maximum shaft diameter. Assuming that the load is nearly torsional. What is maximum load permissible on each wheel?
A mild steel shaft transmits 'P' kW at 'N' r.p.m. It carries a central load of 900 N and is simply supported between the bearings 2.5 metres apart. Determine the size of the shaft, if the allowable shear stress is 42 MPa and the maximum tensile or compressive stress is not to exceed 56 MPa..Power (P) 22 in kW , Speed (N) 550 in Rpm
The steel alloy shaft having a diameter of 38 mm is used to transmit torque, T as shown in Figure Q2(c ). If the allowable shear stress of the shaft is 81kPa (i) Determine the maximum torque T that can be transmitted by the shaft. (ii) What would be the maximum torque T' if a 25 mm diameter hole is bored through the shaft? (iii) Sketch the shear-stress distribution along a radial line in each case. T T' Figure Q2(c)
A compound shaft consists of two pipe segments. Segment (1) has an outside diameter of 216 mm and a wall thickness of 10 mm. Segment (2) has an outside diameter of 124 mm and a wall thickness of 14 mm. The shaft is subjected to torques Tg = 34 kN-m and Tc = 15 kN-m, which act in the directions shown. Determine the maximum shear stress magnitude in segment (2). (1) O 62.5 MPa O 80.7 MPa O 85.3 MPa O 73.5 MPa O 66.2 MPa
A steel core is bonded firmly to the copper tube (shell) to form the shaft shown. The length of the shaft is 450 mm and the end A is fixed to the wall. Take the shear modulus of steel and copper as 76 GPa and 38 GPa, respectively. The diameter of the core is 60 mm and the outer diameter of the shaft is 100 mm. Determine the maximum external torque (Tmax) so that the absolute maximum shear stress for any point H on the surface of the copper shell does not exceed 50 MPa. 450 mm A 100 mm 60 mm В Tmax =? kN · m
3. A solid shaft is shown below. If d= 100 mm, / = 1 m, Me = 2n kN-m, and the allowable shear stress of the material is [ t]= 40 MPa. (a) determine the maximum shear stress and check the strength of the shaft; (b) if OC = d/4, determine the shear stress of point C. it •C B M.