1210 N/m could be correct? I tried 1213 N/m last time. The steel bar AB has a rectangular cross section.(Figure 1)Part AIf it is pin connected at its ends, determine the maximum allowable intensity w of the distributed load that can be applied to BC without causing bar AB to buckle. Use afactor of safety with respect to buckling of 1.4. Est = 200 GPa, oy = 360 MPa.Express your answer to three significant figures and include the appropriate units.HA?Nw =1210Figure1 of 1SubmitPrevious Answers Request AnswerX Incorrect; Try Again; 2 attempts remainingBReview your calculations and make sure you round to 3 significant figures in the last step.5 m3 mProvide FeedbackNext >20 mm30 mm20 mmy

Answered: Image /qna-images/answer/2bd780bb-0bd5-4435-ae78-e969c9c76c56.jpg

The steel bar AB has a rectangular cross section. (Figure 1) Part A If it is pin connected at its ends, determine the maximum allowable intensity w of the distributed load that can be applied to BC without causing bar ABto buckle. Use a factor of safety with respect to buckling of 1.4. E = 200 GPa oy = 360 MPa Express your answer to three significant figures and include the appropriate units. N w = 1210 Figure < 1 of 1 Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Review your calculations and make sure you round to 3 significant figures in the last step. 5 m 3 m Provide Feedback Next > 20 mm 30 mm -20 mm

The steel bar AB has a rectangular cross section. (Figure 1) Part A If it is pin connected at its ends, determine the maximum allowable intensity w of the distributed load that can be applied to BC without causing bar ABto buckle. Use a factor of safety with respect to buckling of 1.4. E = 200 GPa oy = 360 MPa Express your answer to three significant figures and include the appropriate units. N w = 1210 Figure < 1 of 1 Submit Previous Answers Request Answer X Incorrect; Try Again; 2 attempts remaining Review your calculations and make sure you round to 3 significant figures in the last step. 5 m 3 m Provide Feedback Next > 20 mm 30 mm -20 mm

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.22P: The cross section of a column built up of two steel I-beams (S 150 × 25.7 sections) is shown in the...

See similar textbooks

Similar questions

A cantilever aluminum column has a square tube cross section with an outer dimension of 150 mm. The column has a length L = 4 m and is designed to support an axial load of 45 kN. Find the minimum required thickness of the section if the factor of safety n = 2.5 with respect to buckling. Assume that the modulus of elasticity is 72 GPa and the proportional limit is 480 MPa.
A rigid bar of length L is supported by a linear elastic rotational spring with rotational stiffness ßRat A. Determine the critical load Pcr for the structure.
A fixed-pinned column is a W310 × 21 steel shape and is designed to carry an axial load of 125 kN. Determine the maximum permissible height L of the column if a factor of safety n = 2.5 is required with respect to the buckling of the column. Use E = 205 GPa and assume that the proportional limit is 340 MPa. The column may buckle about either axis of the cross section.
A fixed-end column with circular cross section is acted on by compressive axial load P. The IS-ft-long-column has an outer diameter of 5 in., a thickness of 0.5 in., and is made of aluminum with a modulus of elasticity of 10,000 ksi. Find the buckling load of the column.
An aluminum pipe column (E = 10,400 ksi) with a length L = 10.0 ft has inside and outside diameters d1= 5.0 in. and d2= 6.0 in., respectively (sec figure). The column is supported only at the ends and may buckle in any direction. Calculate the critical load Pcrfor the following end conditions: (a) pinned-pinned, (b) fixed-free, (c) fixed-pinned, and (d) fixed-fixed.
The upper end of a WE × 21 wide-flange steel column (E = 30 × 103ksi) is supported laterally between two pipes (see figure). The pipes arc not attached to the column, and friction between the pipes and the column is unreliable. The base of the column provides a fixed support, and the column is 13 ft long. Determine the critical load for the column, considering Euler buckling in the plane of the web and also perpendicular to the plane of the web.
Calculate the critical load PCTfor a W 8 × 35 steel column (see figure) having a length L = 24 ft and E = 30 × 106 psi under the following conditions: The column buckles by bending about its strong axis (axis 1-1). the column buckles by bending about its weak axis (axis 2-2). In both cases, assume that the column has pinned ends.
A rigid L-shaped frame is supported by a steel pipe column AB (sec figure) and is subjected to a horizontal load F = 140 kips. If the pipe has an outside diameter d = 4 in. and a factor of safety of 2.5 is required with respect to Euler buckling, what is the minimum acceptable thickness f of the pipe? Assume that E = 30,000 ksi for AB.
The figure shows an idealized structure consisting of two rigid bars with pinned connections and linearly elastic rotational springs. Rotational stiffness is denoted ßR. Determine the critical load Pcrfor the structure.
The figure shows an idealized structure consisting of two rigid bars joined by an elastic connection with rotational stiffness ßR. Determine the critical load PCTfor the structure.
An idealized column is made up of rigid bars ABC and CD that are joined by a rotational elastic connection at C with stiffness ßR. The column has a roller support at B and a pin support at D. Find an expression for the critical load Pcr of the column.
A slender bar AB with pinned ends and length L is held between immovable supports (see figure). What increase T in the temperature of the bar will produce buckling at the Eu1er load?