The steel shaft shown rotates 4 r/s with 30 kW taken off at A, 15 kW removed at B, and 45 kW applied at C. Using G= 83x 10^9 N/m^2. Find the maximum shearing stress and the angle of rotation of Gear A relative to gear C/ 30 kW 15 kW 45 kW 30 mm e 75 mm a 4m -2m- 1.592 kN-m

The steel shaft shown rotates 4 r/s with 30 kW taken off at A, 15 kW removed at B, and 45 kW applied at C. Using G= 83x 10^9 N/m^2. Find the maximum shearing stress and the angle of rotation of Gear A relative to gear C/ 30 kW 15 kW 45 kW 30 mm e 75 mm a 4m -2m- 1.592 kN-m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.12P

See similar textbooks

Related questions

Q: The steel shaft shown rotates 4 r/s with 30 kW taken off at A, 15 kW removed at B, and 45 kW applied…

A: Solution: NS = 4rps∴ ω = 2π x Ns = 2π x 4 = 8π rad/s.Now: Torque acting T =…

Q: A solid shaft 100 mm diameter transmits 100.6 horsepower with a maximum allowable shear stress 25…

A: given data as per question diameter of shaft = 100 mm =0.1 m power transmitted = 100.6 hp = 75.017…

Q: Under normal operating conditions, the electric motor shown in Figure Q4 exerts a torque of 2.4 kNm…

A: Given data: TB=1.2 kNTC=0.8 kNTD=0.4 kNdAB=54 mmdBC=46 mmdCD=46 mmdDE=40 mm Need to determine the…

Q: Q3: Determine the dimensions of a hollow shaft with a diameter ratio of 3:4 which is to transmit 60…

Q: Find the diameter of the solid shaft. Torque = 190 kNm Maximum shear stress = 210 MN/m2

A: Substitute the given values in the Maximum shear stress equation to get the diameter of the shaft.

Q: The torque transmitted by a solid shaft of diameter 10 mm and shear stress 75 MPa Select one: a.…

A: Given data: Diameter of the solid shaft, D= 10mm Shear stress, s=75MPa=75N/mm2

Q: A solid 1.750-in.-diameter steel shaft is subjected to torques TB = 290 lb-ft and Tp= 100 lb-ft,…

Q: A solid shaft transmits 30 kW at 3 rev/s. Determine the cubic diameter of the shaft (d3 ),if the…

Q: A solid steel circular shaft transmits 18 kW of power at 120 rpm. Determine the minimum diameter of…

Q: Problem 4

Q: * While transmitting power ofa steam turbine, the angle of twist of a rotating shaft was measured…

A: Given: · Angle of twist of a rotating shaft ∴ θ = 1.2° = 1.2×π180 =…

Q: 4 kN m 1.5 kN m Aluminum Steel Bronze B 100 mm 75 mm 3m 2 m 1.5 m- C FIG. P3.12 FIG. P3.11 3.12 The…

A: For solution refer below images.

Q: Example1: A solid shaft in a rolling mill transmits 20 kW at 120 r.p.m. Determine the diameter of…

A: The above question is based on Torsion of solid shaft.

Q: 4) Shafts with lengths 5m and 4 m are connected by gears. The diameter and shear modulus for both…

A: Given, Lengths of the shafts , 5 m and 4 m. Diameter of the shafts , d = 10cm Shear modulus of the…

Q: A solid shaft is to transmit 22kW at 110 rpm. Determine the diameter of the shaft if the shearing…

Q: Q2/ A hollow shaft has to transmit 6MW at 150rev/min. The maximum allowable stress is not to exceed…

Q: A solid shaft in a rolling mill transmits 30kW at 100 rpm. Find the diameter in mm of the shaft so…

A: Answer: The diameter of the shaft is 63.35 mm. Hence, the correct answer is option (c).

Q: 3. A motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B…

Q: The rotation or twist in degrees of a shaft, 800 mm long, subjected to a torque of 80 N-m, 20 in…

Q: (a) the maximum shear stress in the shaft; and (b) the angle of twist in degrees. Use G =12 x 106…

Q: 6. A propeller shaft in a ship is 350 mm in diameter. The allowable working stress in shear is 50…

Q: For the gear system shown in the figure, the diameter of shaft AB=12 mm. Determine the diameter of…

Q: Lets consider a solid circular shaft having a diameter D = 40 mm subjected to a triangular…

A: Given: The diameter of solid circular shaft, D = 40 mm The torque acting on shaft, t = 100 N.m/m The…

Q: The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof…

A: Given: The power, P = 300 kW The speed of shaft, N = 32 Hz The power at gear B, P1 = 120 kW The…

Q: A steel marine propeller shaft 13 inches in diameter and 15 ft long is used to transmit 9,426 hp at…

A: GIVEN DATA- D=13in L=15ft P=9426hp N=189rpm G=12*10^6 psi WE HAVE TO FIND SHEAR STRESS

Q: A solid 1.250-in.-diameter steel [G = 11,000 ksi] shaft is subjected to torques TB = 175 lb-ft and…

Q: Calculate the unit shearing stress at the inner surface of a hollow shaft which D = 150 mm and d =…

Q: A solid shaft is transmitting 1 MW at 250 r.p.m. Determine the diameter of the shaft if the maximum…

A: As per our guidelines we have to answer one question only so, post the question separately and…

Q: find the maximum shear stress induced in a solid circular shaft of diameter 150 mm when the shaft…

Q: A steel propeller for a windmill transmits 5.7 kW at 43.4 rpm. If the allowable shear stress in the…

Q: Using G =83 GPa, determine the maximum shearing stres

Q: A steel shaft with a diameter 1.95 inches and length 4.35 feet transmits 80 HP from an electric…

A: Given dataDiameter = d= 1.95 incheslength = 4.35 feetAllowable shear stress = τallow = 8600…

Q: WHILE TRANSMITTING POWER OF A STEAM TURBINE, THE ANGLE OF TWIST OF A ROTATING SHAFT WAS MEASURED AND…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Q: A propeller shaft in a ship is 350mm in diameter and 5.25 m in length. The allowable shearing stress…

Q: A motor supplies a torque of 5.5KNm to the constant diameter steel (G= 80GPa) line shaft shown in…

Q: • For the solid shaft shown in the figure, determine the maximum shearing stress. And the twisting…

Q: 3) Determine the maximum applied torque T without exceeding a maximum shearing stress of 50MPA for…

Q: A solid circular shaft of steel is transmitting 20 kW of power at 120 rpm. Determine the minimum…

Q: A steel marine propeller shaft 14 in. in diameter and 18 ft long is used to transmit 5000 hp at 189…

A: Given data: Unit conversions used are:

Q: Design a suitable diameter for a circular shaft required to transmit 90 kW at 180 r.p.m. The shear…

A: GIVEN DATA- MAXIMUM SHEAR STRESS = 70MPa POWER P=90KW SPEED N=180 r.p.m. MAXIMUM TORQUE = 140% OF…

Q: A hollow circular shaft is required to transmit 300 metric horsepower at 200 r.p.m. The maximum…

A: Given data

Q: A Solid shaft transmits 600 N.m torque. If the maximum shear stress induced in the shaft is 50…

A: Given Data, T = Torque transmitted by the solid shaft = 600 Nm = 600 x103 Nmm ?max= Maximum shear…

Q: Q2/ A hollow shaft has to transmit 6MW at 150rev/min. The maximum allowable stress is not to exceed…

Q: 0.4 m 0.6 m Fig. P3.48 0.3 m PROBLEM 3.48 The electric motor exerts a torque of 800 Nm on the steel…

Q: Maximum shear stress developed on the surface of a solid circular shaft under pure torsion is 240…

Q: Q3) A ship's propeller shaft has external and internal diameters of 25 cm and 15 cm. What power can…

Q: Q. Determine the value of the torque T of the shaft shown in the figure, if the permissible shearing…

A: When the force is applied in tangential direction in the plane of transverse cross-section, torque…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

The steel shaft show rotates

The steel shaft shown rotates 4 r/s with 30 kW taken off at A, 15 kW removed at B, and 45
kW applied at C. Using G= 83x 10^9 N/m^2. Find the maximum shearing stress and the angle
of rotation of Gear A relative to gear C/
30 kW
15 kW
45 kW
30 mm e
75 mm a
4m
-2m-
1.592 kN-m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A solid 14 mm diameter steel shaft is fixed to a wall at E. Torques are applied to gears A, C and D as shown. Determine the maximum shear stress in the shaft and the rotation angle for gear A. G = 80 GPa 40 N•m 280 N m 0.5 m 150 N-m B 0.3 m P. 100 mm 0.4 m (a)
The four gears shown are attached to a steel shaft that is rotating at 2 Hz. Gear B supplies 70 kW of power to the shaft. Of that power, 20kW are used by gear A, 20 kW by gear C and 30kW by gear D. G=83 GPa for steel -20KW JOKN -20kw -30kW 2m 1.5m 1.5m B (a) If a uniform shaft diameter of 125 mm B speci fied, detenmine the angle of rotation of A relative to D. O f segment Co is to be replaced lay a hollaw Shaft with an inside diameter of 80 mm, what is the outside diameter if the stress is not to excced 70 MPa.
The shaft ABC shown in the figure is drivenby a motor that delivers 300 kW at a rotational speedof 32 Hz. The gears at B and C take out 120 kW and180 kW, respectively. The lengths of the two parts ofthe shaft are L1 = 1.5 m and L2 = 0.9 m.Determine the required diameter d of the shaft ifthe allowable shear stress is 50 MPa, the allowableangle of twist between points A and C is 4.0°, andG = 75 GPa.
The steel shaft with two different diameters rotates at 4.9 Hz. The power supplied to gear C is 54.1 kW, of which 26.9 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 55.5 mm, h = 68.9 mm, L = 4.2 m, M = 2.8 m, and G = 83.46 Gpa. Round off the final answer to two decimal places.
The steel shaft with two different diameters rotates at 4.5 Hz. The power supplied to gear C is 51.7 kW, of which 30.4 kW is removed by gear B. Find the angle of rotation of gear A relative to gear Cif d = 57.3 mm, h = 68.9 mm, L = 4.2 m, M = 2.4 m, and G = 83.16 Gpa. Round off the final answer to two decimal places. A d Bh C | — L M →
The solid steel shaft is supported by the frictionless customer on D and E. This system The mile provided 5 kW of power in w dev / second and was connected to a motor at C. wwww ww www ww ww www wwwm www w A and B If gears get primary 2 kW and 3 kW, determine the minimum shaft diameter. w rotation speed and The safety shear stress is known and is included in the table below. pictures. wwww ww wwwwwwwww www wwwwww wwwwwwww wwwwwwwww w(cycle/second) = 100 tem(Mpa) = 40 3 kW 5 kW 2 kW A D B E C _
A steel shaft with a constant diameter of 60 mm is loaded by torque applied to gears attached to it as shown in the figure. Using G=83 GPa, determine the relative angle of twist of gear D relative to gear A.The steel shaft shown in figure rotates at 6 Hz with 55 kW taken of at A, 40kW removed at B and 95 kW applied at C. Using G =83 GPa, determine the maximum shearing stress and the rotation of gear A relative to gear C.
3. The transmission shaft shown receives power at gear A and transmits them to gear B and gear C. Determine the maximum stress in the shaft. Determine the total angle of twist. Use G = 70 GPa. 3kW @ 1000 rpm 2 kW 1 kW A 200 mm 200 mm Ø 25 mm Ø 20 mm
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C.a)Determine the maximum shear stress in the shaft in ksi.b)Determine the angle of twist in degrees of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible.
A solid brass shaft is loaded as shown below by two torques TB- segments are LAB = 700 mm and LBC 600 mm. A dBc = dAB mm LAB mm B Com dBC For brass, G = 41 GPa. Neglect the effect of any stress concentrations. LBC Determine the smallest diameters dAB and dBC for which an allowable shear stress of 50 MPa is not exceeded. Express each diameter as an integer in units of mm. dAB To 1100 Nm and Tc = 300 Nm. The lengths of the two Determine the magnitude of the total angle of twist in the shaft caused by the two applied torques for the diameters found previously Express your result in units of radians with five decimal places of accuracy. PAC = rad
A motor supplies a torque of 5.5KNm to the constant diameter steel (G= 80GPa) line shaft shown in the figure. Three machines are driven by the gears B, C, and D on the shaft, and they required torques of 3.0KNm, 1.5KNm, and 1.0KNm, respectively. Determine: a. The minimum diameter required if the maximum shearing stress in the shaft is limited to 100MPa.b. The rotation of gear D with respect to the coupling at A if the coupling and gears are spaced at 2m intervals and the shaft diameter is 75mm.