onThe three phase power and line-line ratings of the below electric power system is given below.VmOBOGMG: 50 MVA22 KVX-8%T: 50 MVA22/40 KVX= 4%M: 432 MVA36 KVX-8%By choosing 100 MVA and 22 KV on the generator side as base values, the new per unit impedance of the generator sand the new perunit impedance of the motor is

Answered: Image /qna-images/answer/7ca9af60-5969-435b-afd2-ed5f6facd8db.jpg

The three phase power and line-line ratings of the below electric power system is given below Vm OBETO G M G: 50 MVA 22 KV X=8% T: 50 MVA 22/40 KV M: 43.2 MVA 36 KV X-8% By choosing 100 MVA and 22 KV on the generator side as base values, the new per unit impedance of the generatoris = and the new perunit impedance of the motor s

The three phase power and line-line ratings of the below electric power system is given below Vm OBETO G M G: 50 MVA 22 KV X=8% T: 50 MVA 22/40 KV M: 43.2 MVA 36 KV X-8% By choosing 100 MVA and 22 KV on the generator side as base values, the new per unit impedance of the generatoris = and the new perunit impedance of the motor s

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.48P

See similar textbooks

Similar questions

two alternators A and B having 5% speed regulation are working in parallel at a station. Alternator A is rated at 15 MW while B is at 20 MW. When the total load to be shared is 12 MW, then how much of the load will be shared by the alternator B?
Three zones of a single-phase circuit are identified in the figure with a generator voltage specification of 240 V. The zones are connected by the transformers T1 and T2, whose ratings are shown below.Using base values of 30 kVA and 240 volts in zone 1, draw the pu circuit and determine the pu impedance and pu source voltage. Then calculate the load current in pu and in amperes.*Round the final answer to four decimal places, polar form, and label it with the correct units.
synchronous generator threewThe phases are rated at 1000 kVA and operate at a voltage of 6.6 kV. The product resistance per phase is 0.38 ohms and the leakage reactance is 0.5 ohms per phase. The generator works to provide full load at a power factor of 0.85 delayed and at normal voltages. Find the value of the no-load voltage.
The one-line diagram of a simple power system is shown in Figure below. The neutral of each generator is grounded through a current-limiting reactor of 0.25/3 per unit on a 100-MVA base. The system data expressed in per unit on a common 100-MVA base is tabulated below. The generators are running on no-load at their rated voltage and rated frequency with their emfs in phase. G Stark Item Base MVA Voltage Rating X' x² 20 kV 20 kV 20/220 kV 20/220 kV 100 0.05 0.15 0.15 0.10 0.10 220 kV 0.125 0.125 0.30 0.15 0.25 025 0.7125 0.15 100 100 0.15 0.05 0.10 0.10 0.10 100 0.10 100 100 Lu La 220 kV 0.15 220 kV 0.35 100 A balanced three-phase fault at bus 3 through a fault impedance Zf= jo.I per unit. The magnitude of the fault current in amperes in phase b for this fault is: Select one: A. 345.3 B. 820.1 C. 312500 3888888 产产

6. A 3 phase fault occurs at point F as shown in figure. Determine the critical clearing anglefor the system. The generator is delivering 1.0 p.u power under prefault conditio
1-Which function we call for three phase short circuit occurs in synchronous generator armature terminals at no load condition a.symshort b.lgfault c.llfault d.symfault 2-The FACTS devices support to control a.susceptance b.reactive power c.real power d.apprant power
Q2 Two three-phase, 6.6 kV, Y-connected synchronous generators are operating in parallel to supply a load of 3000 kW at 0.8 power factor lagging. The synchronous reactance per phase of machine A is j10 Q, while that of machine B is j12 Q (winding resistance and losses are negligible). The excitation of machine A is adjusted so that it delivers 150 A at a lagging power factor, and the governors that control the input torque of the generator prime movers are set such that the load is shared equally between the two machines. a. Determine the following for each machine: i. the armature current; ii. the power factor; ii. the excitation voltage, Ef; and, iv. the power angle. Neatly sketch a phasor diagram for machine A, taking the terminal voltage as the reference. Ensure all phasors are labelled, and all angles indicated. b.
A generator is rated 100 MVA, 22 kV. Its Y connected windings have areactance of 1.1 per unit. Find the reactance of the winding. Then find a new per unit value of reactance of the generator for 100 MVA and 20 kV.
b) Two synchronous generators, G2 and G2, are connected parallelly supplying a load. Generator G1 has a no-load frequency of 50.5 Hz and a slope of 300 MW/Hz. Generator G2 has a no-load frequency of 50.2 Hz and a slope of 500 MW/Hz. The load consumes 250 MW real power. (1) At what frequency does this system operate, and how much power is supplied by each of the two generators? (ii) An additional 100 MW load is added to this power system. What is the new system frequency, and how much power do G1 and G2 supply? (iii) The governor set point of G2 is changed to control system frequency back to 50 Hz. Determine the G2 governor set point.
The reactance of a generator is given as 0.25 per-unit based on the generator’s of 18 kV, 500 MVA. Find its per-unit reactance on a base of 20 kV, 100 MVA. a. 0.0505 b. 0.0605 c. 0.0405 d. 0.0606
READ THE PROBLEM AND JUST DRAW CIRCUIT DIAGRAM. NO NEED TO SOLVE ANYTHING. A short shunt compound generator delivers 150A at a terminal voltage is 230V.The shunt field current is 2.5A. The resistances of the armature, series field and diverterare 0.032 ohm, 0.015 ohm and 0.03 ohm respectively. Calculate the electrical efficiencyof the generator at this load. Modify the circuit diagram on the picture based on the problem. Answer: 95.7%
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --