the torque exerted by the prime D.C. shunt generator which delivers 185A at a terminal p.d. of 240 V if you know the shunt field resistance is 55 ohm ,and the armature resistance is 0.019 ohm , then find E.M.F commercial , mechanical , electrical efficiencies, output of prime and cupper losses , let dynamo Find mover of generated , motor running at 950 r.p.m

the torque exerted by the prime D.C. shunt generator which delivers 185A at a terminal p.d. of 240 V if you know the shunt field resistance is 55 ohm ,and the armature resistance is 0.019 ohm , then find E.M.F commercial , mechanical , electrical efficiencies, output of prime and cupper losses , let dynamo Find mover of generated , motor running at 950 r.p.m

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A 2 pole wave wound dc generator has 44 slots, each slot having 20 conductors. The flux/pole is 0.018 weber. At what speed the armature be rotated to get an induced emf of 220 V. What will be the induced emf developed if the armature winding is lap connected and runs at the same speed. Speed Generated Emf when lap connected
The emf generated in each conductor of a 6-pole simplex wave armature winding is 0.48 V. If the armature has 42 slots and 125 commutator segments, and there are four turns per armature winding element, find the terminal voltage of the generator. a. 288 V b. 264 V c. 192 V d. 240 V
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
A 6 pole wave wound d.c. shunt generator has 500 conductors. A generator delivers 50 kW of power at 250 voltage at full load. The resistance of the field circuit is 125 2. Actual brush shift is 10°. Then find the demagnetizing and cross magnetizing ampere turns per pole and how many additional turns must be wound on each pole to eliminate the demagnetizing effect.
A short shunt compound generator supplies a load of 20 kW at 500 V. The armature, series and shunt field resistance are 0.10 ohm, 0.05 ohm, and 100 ohms respectively. Find the power developed in the armature. Choices: 24600 W 20500 W 22800 W 25400 W
A 4 pole, lap wound, d.c. generators has 42 coils with 8 turns per coils. It is driven at 1120 r.p.m. If useful flux per pole is 21 mWb, calculate the generated e.m.f. Find the speed at which it is to be driven to generate the same e.m.f. as calculated above, with wave wound armature.
A DC generator with 8 pole, duplex lap winding excited with a flux of 3mWb/ pole. The number of parallel path in the winding is A 12 B 8 C 16 D 4
An 10-pole d.c. generator has 390 armature conductors, and a useful flux of 32 mWb per pole. What will be the e.m.f. generated if it is lap-connected and runs at 1070 rpm? Eg
Example : In a 110 V, d.c. compound generator, the resistance of the armature, shunt field and series field are 0.06 , 25 and 0.04 respectively. The load consists of 200 lamps each rated at 55 W, 110 V. Find the total e.m.f. generated and the armature current when the machine is connected in (a) long shun
18. A 4-pole lap-wound armature has 144 slots with two coil sides per slot, each coil having two turns. If the flux per pole is 20-mWb and the armature rotates at 720-rpm. What is the induced voltage? B. 138.24 V C. 332 V D. none of these A. 120 V pruttha
The armature of 6 pole d.c. generator has a wave winding containing 664 conductors.Calculate the generated e.m.f. when flux per pole is 0.06 water and the speed is 250 r.p.m. At what speed must the armature be driven to generate an e.m.f. of 250 V if the flux pole is reduced to 0.058 weber?
A 500 V, 250 kW, long shunt compound generator induces an e.m.f. of 480 V whenrunning at 1000 r.p.m. no load. On full load the spped of the machine drops to 975r.p.m. the flux increases by 15% and the terminal voltage rises to 500 V. If theseries and shunt field resistances are 0.02 ohm and 100 ohms respectively,calculate the armature resistance. Assume a voltage drop of 1V per brush.[Ans.