The uniform slender rod AB of weight 5 lb and length 30 in. forms an angle β = 30° with the vertical as it strikes the smooth corner shown with a vertical velocity v1 of magnitude 8 ft/s and no angular velocity. Assuming that the impact is perfectly plastic, determine the angular velocity of the rod immediately after the impact.

The uniform slender rod AB of weight 5 lb and length 30 in. forms an angle β = 30° with the vertical as it strikes the smooth corner shown with a vertical velocity v1 of magnitude 8 ft/s and no angular velocity. Assuming that the impact is perfectly plastic, determine the angular velocity of the rod immediately after the impact.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter9: Moments And Products Of Inertia Of Areas

Section: Chapter Questions

Problem 9.74P

See similar textbooks

Similar questions

A body of dimension 2.0 m x 1.0 m x 3.0 m weighs 3924 N in water. Find its weight in air in N. a.60891 b.65745 c.67342 d.62784
Change of Ttork required by a machine for rotational movement with rotation angle T(0)=5000[1+5cos(30)-6sin (30)] (Nm ) is given as. The rotation speed of the machine is below 711 r/min mass moment of inertia required to allow it to move without landing and without leaving above 729 rpm find its value. Please select one: 2 A.241,473 kg-m B.119,592 kg-m2 2. C.183,181 kg-m D.221,264 kg-m 2. E.165,845 kg m 2. F.262,223 kg * m G.126,304 kg m H.150,179 kg-m 2 1,201, 759 kg-m J.136,759 kg-m
6:38 ul LTE Screenshot_20201226-183601_Driv... Solar Probe Plus, Working with Angular Diameter The Solar Probe Plus mission will be launched in 2018 for a rendezvous with the sun in 2024. To lose enough energy to reach the sun, the spacecraft will make seven fly-bys of Venus. The 480 kg spacecraft, costing $740 million, will approach the sun to a distance of 5.8 million km. Protected by the heat shield will be five instruments that will peak over the edge of the heat shield and measure the particles and radiation fields in the outer solar corona. At the closest approach distance, the sun will occupy a much larger area of the sky than what it does at the distance of Earth. The angular size of an object as it appears to a viewer depends on the actual physical size of the object, and its distance from the viewer. Although physical size and diameter are usually measured in terms of meters or kilometers, the angular diameter of an object is measured in terms of degrees or radians. The…
The opposite figure is composed of a rectangle (b=16.8 , h=8.4 m , density 8 kg/m2) and a triangle (b=16.8 , a=4.2 m , density 16 kg/m2 ). The mass of total shape is E h x b/4 h/3 A В Select one: O A. 5622.22 О В. 2066.00 O C. 1693.44 O D. 5960.91 O E. 4436.81
p 10:04 A docs.google.com 13% LTE Asiacell In. Use the method of composite areas to calculate the centroidal coordinates of the plane regions shown. F3in- 6 ir. 2 in. +I in. 7 in. 2 in. 7 in. 0.87 in, 5.96 in 1.87 in, 6.96 in 2.87 in , 7.96 in 3.87 in, 8.96 in محو النموذج إرسال إرسال كلمات المرور عبر نماذج Go ogle مطلقا. تم إنشاء هذا النموذج خارج نطاقك. الإبلاغ عن إساءة الاستخدام شروط الخدمة - سياسة الخصوصية
A flywheel connected to a punching machine has to supply energy of 400 Nm while running at a mean angular speed of 20 rad/s. If the total fluctuation of speed is not to exceed ±2%, the mass moment of inertia of the flywheel in kg-m² is (a) 25 (b) 50 (c) 100 (d) 125
Based on Figure Q4(a), the diaphragm in a differential pressure gauge deflects proportionally with the pressure difference across it. This deflection is used to measure the pressure difference, dp. To operate well, the material must not fail under the loading, and it should have a large deflection in order to increase the sensitivity of the measurement. The equations below for maximum stress and of a circular diaphragm of fixed radius are important to answer this question. The diaphragm thickness is t, E is Young's Modulus, and v is Poisson's ratio. a? Omx = Ap: 2t2 3Apa*(1 – v²) 16E13 Using the information above, explain how you would determine in different ways the M-value for this design. (Answer can be with or without doing the algebra)
FROM SECTION PLANE GIVEN, SKETCH YOUR ANSWER IN THE PROVIDED VIEW. 5. A 6. A A
A turbine is constructed such that is made of a 5.00 kg thick-walled cylinder of length 1.00 m, inner and outer diameter of 35 cm and 50 cm, respectively. Inside the hollow cylinder, four 1.00 kg thin rectangular plates of length 1.00 cm and width of 17.5 cm are connected from the rotation axis of the turbine, which is parallel to the length of the turbine and through the center of the cylinder. (a) Calculate the moment of inertia of the turbine about its rotation axis. The turbine is initially rotating when it is turned off by a constant torque of 0.41 mN and slowly rotates until it come to a full stop after 3.00s. (b) What is the angular acceleration of the turbine? (c) What was the rotational kinetic energy of the turbine at the instant it starts to decelerate? 35.0 cm 1.00 m 50.0 cm
A flywheel connected to a punching machine has to supply energy of 400 Nm while running at a mean angular speed of 20 radians/s. If the total fluctuation of speed is not to exceed ±2%, the mass moment of inertia of the flywheel in kg – m2 is
A cube of 45 mm side rests with a face on HP such that one ofits vertical faces is inclined at 30° to VP. A section planeparallel to V.P. cuts the cube at a distance of 15 mm from thevertical edge nearer to the observer. Draw its top and sectionalfront views.
0.08 m,x 0.225 0.75 0.08 m. O: 1.08 b' 0.108 (c) Couple polygon. (d) Force polygon. Fig. 21.11 Page 18 of 19 Balarcing of Rotating Masses H.W. 2: A shaft carries five masses A, B, C, D and E which revolve at the same radius in planes which are equidistant from one another. The magnitude of the masses in planes A. Cand Dare 50 kg. 40 kg and 80 kg respectively. The angle between A and C is 90° and that between C and D is 135°, Determine the magnitude of the masses in planes B and E and their positions to put the shaft in complete rotating balance. 19 Page 19 uf 19 II