The upper jaw D of the toggle press slides with negligible frictional resistance along the fixed vertical column. Calculate the magnitudes of the compressive force R exerted on the cylinder E and the force supported by the pin at A if a force F= 215 N is applied to the handle at an angle 0 = 74°. 260 mm 150 mm 150 mm C

The upper jaw D of the toggle press slides with negligible frictional resistance along the fixed vertical column. Calculate the magnitudes of the compressive force R exerted on the cylinder E and the force supported by the pin at A if a force F= 215 N is applied to the handle at an angle 0 = 74°. 260 mm 150 mm 150 mm C

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.36P: The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find...

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
200 N A block placed under the head, of the claw hammer as shown greatly facilitates the extraction of the nail. If the 200-N pull on the handle is required, to pull the nail calculate the tension T in the nail and the magnitude A of the force exerted by the hammer head on the block. The contacting surfaces at A are sufficiently rough to 200 mm 20 45 mm prevent slipping 1. 50- |Imm L->
The upper jaw D of the toggle press slides with negligible frictional resistance along the fixed vertical column. Calculate the compressive force R exerted on the cylinder E and the force supported by the pin at A if a force F = 230 N is applied to the handle at an angle 0 = 73°. 340 mm 145 mm OB 145 mm
A pair of 120-N forces is applied to the handles of the small eyelet squeezer. The block at A slides with negligible friction in a slot machined in the lower part of the tool. Neglect the small force of the light return spring AE and determine the compressive force P applied to the eyelet. 120 N 54.5 mm 40 mm C B 13 mm wwwmaE 6.50 mm 120 N -286.6 Answer: P =
For Probs. 1-3, (a) draw the free-body diagrams for the entire assembly (or structure) and each of its parts. Neglect friction and the weights of the members unless specified otherwise. Be sure to indicate all relevant dimensions. For each problem, (b) determine the total number of unknown forces and the total number of independent equilibrium equations. Problem 1 500 N 500 N 1 m 500 N (b) (c) Figure 1 Problem 2 -- Ift 4 ft -1.8 ft 100 lb F1.8 ft - 100 lb 100 lb (а) (b) (c)
A pair of 115-N forces is applied to the handles of the small eyelet squeezer. The block at A slides with negligible friction in a slot machined in the lower part of the tool. Neglect the small force of the light return spring AE and determine the compressive force P applied to the eyelet. 115 N 63.5 mm 50 mm 12 mm D. 6.25 mm 115 N Answer: P =
Determine whether the block shown below is in equilibrium, and find the magnitude and direction of the friction force. Draw the Free-body diagram and show all calculations. Given: coefficient of static friction u, = 0.30 and coefficient of kinetic friction u = 0.25. H=0.30 600N H=0.25 700N 30
FA BO К mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force on the spring FD and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17 ) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees ww
3- Can the system in figure be in static equilibrium in the position shown? The uniform bar AB weight 500 lb, and the weight of block C is 300 lb .Friction at A is negligible and the coefficient of static friction is 0.4 at the other two contact. 10 ft В 30° C 50°
FA K mm L mm- M mm The operation of the fuel pump for an automobile depends on the reciprocating action of the rocker arm ABC, which is pinned at B and is spring loaded at A and D. When the smooth cam C is in the position shown, determine the force acting on pin B along Y axis and input its absolute value. (If your answer is negative, input its positive value such as -17 --> 17) Use the followings; FA=57N FC=246N K=51mm M=12mm L=22mm O=35degrees
The high strength, square-threaded bolt that holds the three plates together has a nominal diameter of 1 in. The coefficient of friction is us = 0.36. The mean diameter of the thread is 0.94 in. The lead of the bolt is L = 0.160 in. Neglect friction between the nut and the washer. Determine the torque one must apply in in. Ib to the nut to induce a tension of 47,500 lb. (Enter the magnitude.) in. · Ib When that tension is achieved, determine the torque in in. · Ib required to loosen the bolt. (Enter the magnitude.) in. • Ib
The 60 kg two-wheeled cart is described in the figure and parameter table below, with G indicating the location of the center of gravity. It is to be pulled so that it goes up the small step. Find the normal force on each wheel, and the magnitude and direction of the force applied at handle. HINT: remember that there are two wheels sharing the load @080 BY NO SA 2021 Cathy Zupke 4₁1 G L₁ L₂ parameter value 0.6 0.5 0.8 0.7 0.2 A L3 LA d L3 units m m m m m B L₂ F For the answers, take to the right and up to be the positive directions. The normal force at each wheel at A in the x direction is Ax= 150 XN The magnitude of the force at B is F Measured from the positive horizontal axis, the angle of F= 45 X° = 212 XN