The W14 x 43 simply supported beam is made of A-36 steel and is subjected to the loading shown in (Figure 1), where to = 2.9 kip/ft. Figure 10 f 0 kip-t 101 > Part A Determine the slope at A, measured counterclockwise. Express your answer in degrees to three significant figures. Part B 1971 ΑΣΦ Submit Request Answer Submit Determine the slope at B, measured counterclockwise. Express your answer in degrees to three significant figures. Lt vec Provide Feedback Η ΑΣΦ Ivec Request Answer ? ? N

The W14 x 43 simply supported beam is made of A-36 steel and is subjected to the loading shown in (Figure 1), where to = 2.9 kip/ft. Figure 10 f 0 kip-t 101 > Part A Determine the slope at A, measured counterclockwise. Express your answer in degrees to three significant figures. Part B 1971 ΑΣΦ Submit Request Answer Submit Determine the slope at B, measured counterclockwise. Express your answer in degrees to three significant figures. Lt vec Provide Feedback Η ΑΣΦ Ivec Request Answer ? ? N

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Identify the correct boundary conditions from the following list for the beam shown. The origin is at A. B L O v = 0 at x = L; dv/dx = 0 at x = L O v = 0 at x = L; dv/dx = 0 at x = 0 O v = 0 at x = 0; v = 0 at x = L O v = 0 at x = 0; dv/dx = 0 at x = 0 O v = 0 at x = 0; dv/dx = 0 at x = L
A beam is shown in the figure below. Part A If M = 1 kip/ft, determine the resultant force the bending stresses produce on the top board A of the beam. Express your answer to three significant figures and include appropriate units. F = NA Submit Value 3 → Request Answer Units ? o 6 in. 1 in.. 6 in. 1.5 in. 12 in. M 1.5 in.
Part A Determine the maximum uniform loading w the W 310 x 21 beam will support if the allowable bending stress is aallow = 170 MPa and the allowable shear stress is Tallow = 92 MPa (Figure 1) Express your answer using three significant figures. Figure 1 of 1 VO AEo It vec W = kN/m Submit Request Answer 3 m 3 m < Return to Assignment Provide Feedback
Using a computer and step functions, calculate the shear and bending moment for the beam if P-16 kN. Use the specified increment AL. starting at point A and ending at the right-hand support. (Round the final answers to two decimal places) ها 1.2 m 16 kN/m AL-0.4m The maximum shear stress is The maximum bending moment is KN. kN m.
E=240 GPa and I = 65.0(106) mm* (Figure 1) Figure 10 kN 3 kN/m -3 m 1 of 1 Part A Determine the slope of end A of the cantilevered beam Express your answer to three significant figures and include the appropriate units. μÀ ja Xb Xa X.10 A=1.44110-5 10 5 rad Submit Previous Answers Request Answer Return to Assignment X Incorrect; Try Again; 3 attempts remaining X Provide Feedback ? TODO
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
The simply supported W8X24 A-36 steel beam AB is loaded as shown in the figure. What is the slope of point B in radians if w = 5.7 kip/ft, L 16.5 ft, Mo = 6.2 kip-ft? Note: Your answer should include units and be to 4 decimal places. Mo Aरू 늘 -
The beam has the cross-sectional area shown in (Figure 1). Figure 8- 8 ft· !!!! 0.3 in.- -8 ft- 8 in. 1 of 1 0.30 in. 10 in. 0.30 in. > Part A Determine the largest intensity of distributed load w that the beam can support so that the bending stress does not exceed max = 22 ksi. Express your answer in kilopounds per foot to three significant figures. W = Submit VE ΑΣΦ ↓↑ Request Answer < Return to Assignment vec Provide Feedback ? kip/ft
• The Precast T-Beam has the cross section shown Determine its weight per meter of its length if it is made from reinforced store concrete and light 20mm diameter cold formed steel reinforcing rods 200mm 250mm 500mm 0 -0 00 Do 350mm 150 150 150 350 t
A a= -0.5 m Submit 15 kN 195| ΑΣΦ | | Determine the minimum dimension a to the nearest mm of the beam's cross section to safely support the load. The wood has an allowable normal stress of allow 12.7 MPa and an allowable shear stress of Tallow = 1.5 MPa. (Figure 1) Express your answer as an integer. Request Answer a vec 1 m 2 a www B 1] ? mm
M 4 in. 30 6 in. Part A Determine the maximum stress in the beam's cross section. Take M = 56 lb - ft (Figure 1) Express your answer to three significant figures and include the appropriate units. Value Units Ởmax = Subrmit Request Answer
Consider the beam and loading shown. The allowable normal stress for the steel used is 152 MPa. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 90 kN A B 90 KN C 0.6 m 0.6 m 0.6 m 90 KN D -1.8 m- Determine the maximum value of the principal stress omax at the junction of a flange and the web. The maximum value of the principal stress omax is MPa.