The zinc contained in a 0.7555-g sample of foot powder was titrated with 21.27 mL 0.01645 M EDTA. Find the percent Zn (MM=65.41) in the sample. Answer: 3.029%
Q: Ag* 0.0000133038 Cr 0.0000133038
A: Concentration of Ag+ = 0.0000133M Concentration of Cl- = 0.0000133M
Q: a. A deepwell water sample of 100 mL was titrated with 0.010 M EDTA at pH 10 ( with Mg-EDTA pH 10…
A: According to Q&A guidelines of Bartleby, we are supposed to answer only the first question out…
Q: A 50.00-mL aliquot of solution containing 0.358 of MgSO4 (FM 120.37) in 0.500 L required 38.08 mL of…
A: Solution - According to the question - Given - Total Moles of Mg2+ = moles of MgSO4 = mass/molar…
Q: A 50.00 mL sample of hard water is titrated with 0.0102 M EDTA solution (volume of blank titration=…
A: Given data,Volume of sample=50mLMolarity of EDTA=0.0102MVolume of EDTA=22.44mLVolume of EDTA for…
Q: 150.0 mL sample of 0.080 M Ca is titrated with 0.080 M EDTA at pH 9.00. The value of log K for the…
A:
Q: A deepwell water sample of 100 mL was titrated with 0.010 M EDTA at pH 12 and consumed 31 mL.…
A:
Q: 0.1500 g of an unknown sample was passed through a column of Amberlite IR-120(+) resin and titrated…
A:
Q: The zinc contained in a 0.7555-g sample of foot powder was titrated with 21.27 mL 0.01645 M EDTA.…
A:
Q: A 100 mL of 0.125 M CH₂COOH solution was shaken with 1.2 g charcoal for 5 min. After filtration, 10…
A: I have given a detailed solution for the problem as follows:
Q: 10) 1.0 gram of CaCO3 was dissolved in HCl and the solution was made up to 1000 ml with distilled…
A:
Q: A hydrated sample weighing 0.2700 g was shaken with 50.0 mL of anhydrous methanol and titrated with…
A: Solution- Data given-A hydrated sample weighing 0.2700 g, 50.0 mL of anhydrous methanol , 0.0150 M…
Q: A freshwater sample containing Ca2+ and Mg2+ will be analyzed using EDTA titration. The EDTA titrant…
A:
Q: 2+ Calculate the mass of Cu (At.wt. 63) that titrated iodometrically with I ,then the liberated I,…
A: Molarity = no. of moles/ vol (Lt)
Q: A 50.00-mL aliquot of solution containing 0.395 of MgSO4 (FM 120.37) in 0.500 L required 39.55 mL of…
A:
Q: Concentration EDTA (M): 1.94e-3 Trial #1 Trial #2 Trial #3 Volume of Water Sample titrated…
A: Given,Concentration of EDTA = 1.94 × 10-3 M = 1.94 × 10-3 mol/LVolume of water sample titrated (mL)…
Q: A 20-mL solution of 0.0659 M AgNO3 was titrated with 20 mL of 0.0509 M NaCl (Ksp = 1.8x10-10).…
A: 20 mL of 0.0659 M AgNO3 solution was titrated with 20 mL of 0.0509 M NaCl solution .The Ksp is…
Q: a - pipette 10.00 mL of 0.100 M CaCl2 stock into 100 ml volumetric flask b - in 100 ml volumetric…
A: Since you have posted a question with multiple sub-parts, we will solve first three subparts for…
Q: You took 25.00 mL of unknown water solution and titrated it with EDTA. The EDTA solution molarity…
A: Interpretation: a) To calculate g of CaCO3 in water if total hardness of water is due to CaCO3. b)…
Q: Which of the following experiments can be described as a displacement titration? A. Calcium in…
A: A displacement titration is a one that involves an analyte displacing a reagent, by forming a…
Q: A 50.0 mL of 0.0400 M EDTA was added to 20.0 mL of 0.0800 M Cu(NO3)2 at pH 5.00. The Kifor CuY- is…
A: GIVEN: Volume of EDTA = 50.0 mL Concentration of EDTA = 0.0400 M Volume of Cu(NO3)2 = 20.0 mL…
Q: To check the hardness of tap water by complexometric titration 50 mL of water sample is required for…
A:
Q: standardized by dissolving 0.5005g of CaCO3 (99.00% purity) in 100.0mL. A 10.00-mL aliquot was then…
A: Introduction : Complexometric titration are used to determine the metal ions by use of complex…
Q: B. Titration Data A 100 mL Kool-Aid solution was made: 0.3210 g of Kool-Aid powder was…
A:
Q: freshwater sample containing Ca2+ and Mg2+ will be analyzed using EDTA titration. The EDTA titrant…
A: Introduction : EDTA is a polydentate chelating ligand which forms a soluble 1:1 complex with most…
Q: Calculate the concentration of an EDTA solution of which 24.22 mL were needed to titrate the Ca2+…
A: Given: Volume of EDTA solution used = 24.22 mL = 0.02422 L…
Q: A river water sample was titrated against 0.0250 M EDTA to test its hardness. of 0.0250 M EDTA. A…
A: Here we have to determine the hard ness of river water in ppm from the following given data from…
Q: In the titration of 50.0 ml of 0.005 M Ca2+ with 0.01 M EDTA ,at pH 10 find the pCa at equivalence…
A: Given, Volume of Ca2+ = 50.0 mLMolarity of Ca2+ = 0.005 MMolarity of EDTA = 0.01 MpH = 10KCaY=…
Q: For the titration of 20.0 mL of 0.0100 M EDTA with 50.0 mL of 0.0200 M MNPO4 at pH = 10.00,…
A: The given information is: Volume of EDTA = 20.0ml Molarity of EDTA= 0.010 M Volume of MnPO4 = 50.0ml…
Q: f 5.85 mL of 0.00832 M EDTA solution were needed to titrate a 0.0225 L water sample to an Eriochrome…
A: Balanced reaction is : Ca2+ + EDTA4- ===> [Ca-EDTA]2-
Q: A 0.2185 g sample of NaCl was assayed using Volhard method using 50 mL of 0.998N silver nitrate and…
A: In the Volhard method, silver nitrate is titrated with chloride solution (NaCl) and then excess…
Q: In the titration of 50 mL 0.02 M Sr² with 0.02 M EDTA in a buffered medium at titrated pH 11,…
A: EDTA is ethylenediaminetetraacetic acid which is an indicator which complexes with the metal ions…
Q: 3. A solution contains 1.694 mg of CoSo. (155.0 g/mol) per milliliter. a. Calculate the volume of…
A: a) Amount of CoSO4 = 1.694 mg/mL Calculation of mass of CoSO4: Mass=1.694 mg mL-1×25 mL=42.35 mg…
Q: solution was prepared by dissolving about 3.0 g of NaH2Y2·2H2O in approximately 1 L of water and…
A: At equivalence point, V1× S1 = V2 × S2 Where V1 and V2 are the initial and final volume…
Q: Analyze and calculate the percentage of nickel in a 1.201 grams sample of nickel ore which was…
A: Ni2+(aq) reacts with CN-(aq) through the reaction below: Ni2+(aq) + 4CN-(aq) (Excess) ---->…
Q: 12-7. Calculate pCo²+ at each of the following points in the titration of 2+ 25.00 mL of 0.020 26 M…
A: The amount of substance that passes into the solution is furnished by the term concentration.…
Q: 7. Sodium nitrite was assayed by residual titration with 0.1N potassium permanganate and 0.1 N…
A: The solution is given below -
Q: The ethyl acetate concentration in an alcoholic solution was determined by diluting a 10.00-mL…
A:
Q: Volhard titration. A 30.00-mL solution of unknown I2 was treated with 50.00 mL of 0.365 0 M AgNO3.…
A:
Q: 2. A river water sample was titrated against 0.0250 M EDTA to test its hardness of 0.0250 M EDTA. A…
A:
Q: A water sample that is believed to contain a maximum hardness of 100.0 ppm CaCO3 was titrated with…
A: The given reaction is a complexometric titration. Parts per million or ppm is the mass of a…
Q: What is the mass of pure dry CaCO3 (MW: 100.0869 g/mol) standard used in the standardization of EDTA…
A:
Q: 25.00 mL of 0.041 32 M Hg2(NO3)2 were titrated with 0.057 89 M KIO3. Hg++ 2103 →→ Hg₂(103)2(s)…
A: Since you have asked a question with multiple sub-parts, as per our company guidelines we are…
Q: Water samples near the Sangonomiya Shrine was titrated against 0.01000 M EDTA to test its water…
A: First case: 50 ml water+ NaOH required 13.5 ml of 0.0100 M EDTA Second case: 50 ml water required…
Q: Assuming that the concentration of EDTA for the experiment was 0.01 M in 20 ml tap water and the…
A: 1. For total Mg2+ and Ca2+ Volume of EDTA added during titrations are as follows: 1st titration:…
Q: A freshwater sample containing Ca2+ and Mg2+ will be analyzed using EDTA titration. The EDTA titrant…
A:
Q: Calculate the volume of 0.0500 M EDTA needed to titrate 29.13 mL of 0.0598 M Mg(NO3 )2. Use a MW…
A:
Q: 10 ml, 25 ml, 50 ml and 60 ml of titrant containing 0.1 M Ce4 + on 50 mL of analyte containing 0.1 M…
A: Solution Balanced equation; Ce⁴+ + Fe2+ --------->Ce3+ +Fe3+ E0 (Fe3+/Fe2+) =0.68V E0(Ce4+/Ce3+)…
Q: Calculate the pCa for the titration of 100 ml of 0.050 M Ca²+ at pH = 8 with 0.1 M EDTA After…
A: The balanced equation for the reaction of Ca2+(aq) and EDTA, Y4-(aq) is: Ca2+(aq) + Y4-(aq) ⇌…
Q: her 250.00 mL sample was then treated with NaOH to precipitate Mg(OH)2 and was then titrated at pH…
A:
Q: A 25.00 mL suspension of milk of magnesia was added to 50.00 mL of 0.1400 M HNO3. The resulting…
A:
The zinc contained in a 0.7555-g sample of foot powder was titrated with 21.27 mL 0.01645 M EDTA. Find the percent Zn (MM=65.41) in the sample. Answer: 3.029%
Step by step
Solved in 2 steps with 2 images
- A 0.1093-g sample of impure Na2CO3 was analyzed by the Volhard Method. After adding 50.00 mL of 0.06911 M AgNO3, the sample was back titrated with 0.05781 M KSCN, requiring 27.36 mL to reach the end point. Report the purity of Na2CO3sample.A 0.1093-g sample of impure Na2CO3 was analyzed by the Volhard Method. After adding 50.00 mL of 0.06911 M AGNO3, the sample was back titrated with 0.05781 M KSCN, requiring 27.36 mL to reach the end point. Report the purity of Na2CO3 sample.5. A 300.0 mg sample containing Na,CO3, NaHCO, and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 ml to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.
- 2. A 0.5131-g sample containing KBr is dissolved in 50 mL distilled water. Titrating with 0.04614 M AgNO3 requires 25.13 mL to reach the Mohr endpoint. A blank titration requires 0.65 mL to reach the same endpoint. Report the % (w/w) KBr in the sample. [Ans. 26.19 % (w/w)]Exp. 4 Volhard method In an experiment of determination of KBr (g%) by volhard method In a flask; 15ml KBr was taken 25 ml 0.05M AgNO3 1 ml nitric acid 1 ml ferric alum indicator Then titration with 0.05M KSCN was done The end point was =15 ml Calculate the mass of KBr in g%5. A 300.0 mg sample containing Na,CO3, NaHCO3 and NaOH and inert material either alone or in some combination was dissolved and titrated with 0.1000 M HCI the titration required 24.41 mL to reach the phenolphthalein endpoint. And an additional 8.67 mL to reach the methyl red endpoint. Determine the composition of the sample and calculate the percent of each titrated component.
- A 0.5131-g sample that contains KBr (MM: 119.0023) is dissolved in 50 mL of distilled water. Titrating with 0.04614 M AgNO3 requires 25.13 mL to reach the Mohr end point. A blank titration requires 0.65 mL to reach the same end point. Report the %w/w KBr in the sample.A 0.9092g sample of wheat flour was analyzed by Kjeldahl method. The ammonia formed was distilled into 50.00 mL of 0.05063 M HCl; a 7.46 mL back titration with 0.04917 M NaOH was required. Calculate the % protein in the flour. Input the value only. Express in 2 SF.Direct titration: 10.90 ± 0.02 mL of an unknown KHP solution required 11.72 ± 0.02 mL of 0.1090 ± 0.0006 M NaOH to reach the end point. What is the concentration of KHP in the unknown solution reported with absolute uncertainty? If the unknown solution was prepared by dissolving 5.128 g of the unknown KHP (204.22 g/mol) in 100.00 mL of water, what is the weight percent of KHP in the sample?
- A 0.5131-g sample containing KBr is dissolved in 50 mL distilled water. Titrating with 0.04614 M AgNO3 requires 25.13 mL to reach the Mohr endpoint. A blank titration requires 0.65 mL to reach the same endpoint. Report the % (w/w) KBr in the sample. [Ans. 26.19 % (w /w)]A 0.1214-g sample of impure Na2CO3 was analyzed by the Volhard method. After adding 50.00 mL of 0.07011 M AgNO3, the sample was back titrated with 0.06021 M KSCN, requiring 27.15 mL to reach the end point. Calculate the purity of the Na2CO3 sample.The ethyl acetate concentration in a alcoholic solution was determined by diluting a 10.00 mL sample to 100.00 mL. A 20.00 mL portion of diluted solution was refluxed with 40.00 mL of 0.04672 M KOH. Ater cooling, the excess OH2 was back-titrated with 3.41 mL of 0.05042 M H2SO4. Calculate the amount of ethyl acetate (88.11 g mol) in the original sample in grams.