Three Impedances each of (11 – j20)Ω are connected in mesh across a three-phase 410V ac supply. Determine the phase current, line current, active power, reactive power drawn from the supply. Also, draw the Phasor diagram for the mesh connection and mark the Line current, phase current line voltage, and phase angle between phase current and phase voltage. phase current (Ip) = Line current = real power=

Three Impedances each of (11 – j20)Ω are connected in mesh across a three-phase 410V ac supply. Determine the phase current, line current, active power, reactive power drawn from the supply. Also, draw the Phasor diagram for the mesh connection and mark the Line current, phase current line voltage, and phase angle between phase current and phase voltage. phase current (Ip) = Line current = real power=

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

4) AC circuit analysis is performed as it was in DC except A) one must use phasors for the voltages and currents and use complex numbers for Impedance. B) one must use phasors for the impedance. C) complex numbers for the V/I ratio are used to represent the power. D) None of the above
Three Impedances each of (12 – j20)Q are connected in mesh across a three-phase 415V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage phase current (Ip) Line current real power reactive power
a. Using Ohm’s Law, compute the voltage and current for eachcomponent. Use the formula Z = Vt / It. b. Compute and record the magnitude and phase angle of the impedanceusing the equation Z= R + RL + jXL – JXC. Use 3uF for the value of C,1.006H for the value of L and for the resistance is computed based onthe specification of the lamp. c. Compute and record for the total power using the formula: Pcomputed = Scosθ d. Compute and record the reactive power and apparent power using theformula Scomputed = V2/ZQcomputed = √S2 − P2 e. Compute for the reactive power (measure) and apparent power(measured) using the formula.Q = PtanθS = P/ cos θ f. Compute the percent difference between the measure and the computedvalue of the impedance.
Impedance of AC circuit and Admittance of AC circuitSHOW THE CIRCUIT USING ANY SOFTWARE OR YOU CAN DRAW IT MANUAALYY thNAKSS
13. In parallel-connected ac circuit, the total current though the circuit is always equal to the phasor sum of the individual current though each element. True False 14. In a R-C parallel circuit, R=10 ohms and Xc=10 ohms, the applied voltage is leading to the circuit total current by 45 degrees (assumed applied voltage is the reference). True False 15. In a R-C series circuit, applied voltage is in phase with the total current. True False
Sketch the phasor diagram of the above circuit in terms of impedance, voltage, and the power triangle.
A circuit consists of an AC voltage source, a 10-ohm resistor, and a capacitor, all connected in series. The magnitude of the impedance of the capacitor is also 10 ohms. Which of the following is true about the phase angle difference between the source voltage and the current through the circuit? a. Insufficient information is given. b. The phase angle difference will be zero degrees. c. The phase angle difference will be 45 degrees. d. The phase angle difference will be 90 degrees.
Two impedances consist of resistance of (15 ohms and series connectedinductance of 0.04 henry) and (resistance of 10 ohms, inductance of 0.1 henryand a capacitance of 100 microfarad, all in series) are connected in series andare connected to 230 volts, 50 – Hz AC source. Find: (a) current drawn, (b) voltageacross each impedance, (c) individual and total power factor. Draw the phasordiagram.
In a R-C parallel circuit, total current is out of phase with the applied voltage." True False In a R-C parallel circuit, total current is out of phase with the applied voltage." True False In parallel-connected ac circuit, the value of the equivalent admittance of the circuit is equal to the phasor sum of the reciprocal of the individual admittances. " True False
3) Write the AC node voltage equations for the following circuit. There is one independent current source and one independent voltage source both with frequency 2000 rad/sec and zero phase shift. Do not manipulate the equations, but put a box around each equation. You should have the same number of boxes as unknowns. 2 ko 20 mH 4 k. 10nF 10 cos(2000t) V 2 cos(2000t) mA
A star connected three phase alternator supplies power to a delta connected resistive load. The alternator has a line voltage of 480V. Each resistor of delta load has 8 ohm of resistance. Find the following values. Line voltage of the load (VL(load)) Phase voltage of the load (VP(load)) Phase current of the load (IP(load)) Line current delivered by the alternator (IL(alt)) Phase current of the alternator (IP(Alt)) Phase voltage of the alternator (VP(Alt)) True power
Predict the output when the input three phase signal is given to the circuit shown in figure.3. IA D1 Va A IpC IB D2 VB 3-phase 4-wire VDC ROAD AC Supply Ic D3 Vc Vphase N Figure.3