Two blocks with masses ma = P kg and mB = 100 kg are connected with a flexible cable that passes over a frictionless pulley as shown in Fig. The coefficient of friction between the blocks is 0.2. If motion of the blocks is impending, determine the coefficient of friction between block B and the inclined surface and the tension in the cable between the two blocks Use the last TWO digits of vour ID for the force P=24 A B 40°

Two blocks with masses ma = P kg and mB = 100 kg are connected with a flexible cable that passes over a frictionless pulley as shown in Fig. The coefficient of friction between the blocks is 0.2. If motion of the blocks is impending, determine the coefficient of friction between block B and the inclined surface and the tension in the cable between the two blocks Use the last TWO digits of vour ID for the force P=24 A B 40°

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.63P: The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The...

See similar textbooks

Similar questions

The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
The leather rein used to fasten the horse to the hitching rail weighs 3.5 oz per foot. The coefficient of static friction between the rail and the rein is 0.6. If a 34-lb force acting on the bridle is sufficient to restrain the horse, determine the smallest safe length L for the free end of the rein.
Calculate the horizontal force P required to push the 85-lb lawn mower at constant speed. The center of gravity of the mower is at G, and the coefficients of rolling resistance are 0.12 for the front wheels and 0.18 for the rear wheels.
The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016, determine the force F required to advance the bar at a constant speed.
The 500KN block shown is in contact with a 45°incline. The w coefficient of friction is 0.25. Determine the horizontal force P necessary to 1.Just start the block up the 45° incline 2.Just to prevent the motion down the incline. 3.lf P=400KN, what is the amount and direction of friction force?
1.The figure shows 3 blocks. Block C hangs from a rope which passes through a fixed cylinder and is attached to block B. Find the maximum mass of block C so that block B does not move to the right. Take into account that there are frictional forces at all points of contact. Consider the given values of the masses and , the coefficient of static friction between surfaces µ1 and the coefficient of friction static between the cylinder and the uC chord. Here are the values: ma= 72 kg mb= 62 kg u1= 0,47 uC=0,37
A 200 lb block is in contact with a plane inclined at 30 degrees to the horizontal. A force P, parallel to and acting up the plane, is applied to the body. If the coefficient of static friction is 0.20, find: a. the value of P to just cause the motion to impend up the plane b. the value of P just to prevent motion down the plane c. the magnitude and direction of the friction force F if P= 80 lbs
2. The 100 – Ib force acts as shown on a 300 - Ib block placed on an inclined plane. The coefficients of friction between the block and the plane are us = 0.25 and Hk = 0.20. Determine whether the block is in equilibrium, and find the value of the friction for the friction force. 300 Ib 100 lb
The coefficients of friction between the block ana the rail are us= 0.25 and uk= 0.20. Given: P2 = 200 N. P1 350 P2 Find the magnitude and direction of the smallest force P1 required to start the block moving up the rail. (You must provide an answer before moving on to the next part.) The magnitude and direction of the smallest force P1 required to start the block moving up the rail is °. N v (Click to select)
1. The blocks shown in the figure below are separated by a solid strut which is attached to the blocks with frictionless pins. If the coefficient of friction for all surfaces is 0.20, determine the value of horizontal force P to cause motion to impend to the right. Assume that the strut is a uniform rod weighing 100 lb. 200 lb MATHalino.com 30 400 lb 45° MATH
Problem 4. A.) If the uniform concrete block has a mass of 500 kg, determine the smallest horizontal force P needed to movethe wedge to the left. The coefficient of static friction between the wedge and the concrete and the wedge and the floor is 0.3. The coefficient of static friction between the concrete and floor is 0.5.ANSWER: P=1797.52; N=1.80kNB.)Refer to problem number 4. Calculate the followinga.) the angle of friction between the wedge and the concrete and the wedge and the floor.Answer: ?????? ??? ????????= ?????? ??? ?????= 16.7ob.) the coefficient of static friction between the concrete and floor.Answer: ????????? ??? ?????= 263.56o