Two loads of 1000 KN and 2500 KN act on points A and B. point C is placed 5 meters below the surface.determine the effective vertical stress acts on C in the following condition.A 5mD 4m BCKN1. Ground water level is -2 m.2. Add an extra 1500 KN to point A. (Dry condition)3. Add 1000 KN vertical point load to point D. (Dry condition)Sand y = 18518 Ysat = 20KNm

Given, Depth of water table = 2 m Depth of water table = 5 m

Two loads of 1000 KN and 2500 KN act on points A and B. point C is placed 5 meters below the surface. determine the effective vertical stress acts on C in the following condition. A 5m D 4m B C Sand y = 18 Ysat = 20 KN m³ 1. Ground water level is -2 m. 2. Add an extra 1500 KN to point A. (Dry condition) 3. Add 1000 KN vertical point load to point D. (Dry condition) KN m³

Two loads of 1000 KN and 2500 KN act on points A and B. point C is placed 5 meters below the surface. determine the effective vertical stress acts on C in the following condition. A 5m D 4m B C Sand y = 18 Ysat = 20 KN m³ 1. Ground water level is -2 m. 2. Add an extra 1500 KN to point A. (Dry condition) 3. Add 1000 KN vertical point load to point D. (Dry condition) KN m³

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q-1: For the following soil system determine the effective stress and pore-water pressure at the point “A" when i) water table is at ground surface ii) water table is 1m below the ground surface (consider ya = 16 kN/m³) 1 m Ysat = 18 kN/m 5 m 5 m Ysat= 18 kN/m Yw = 10 kN/m A Y = 10 kN/m³ (i) (ii)
The circular flexible area uniformly loaded (q=320KN/m^2). Determine the change in vertical stress: (a) at point A. (b) at a point 2m below point A
Ql: Determine the distribution of total stress, pore water pressure and effective stress for the soil profile shown in the figure. Hw NGL yl dry H1 y1 Saturated Y2 Saturated H2
The plan of a flexible circular loaded area is shown. The uniformly distributed load on the flexible area, q, is (100 + last 2 digits of your ID number) kN/m². Determine the increase in the vertical stress, depth of z = 4 +0.01(last 2 digits of your ID number) m below. - 4m A Plan A
1. Given the soil profile below, determine the Total Stress and Effective Stress at points A, B, C, and D. CL 5ft y = 102 Ib/ft3 A • 9ft Ysat = 105 Ib/ft3 B 6ft SM C = 115 Ib/ft3 Ysat 12ft D
Given: 1. Structural Component: Beam 300 mm x 400 mm Column 400 mm x 400 mm Slab thickness 110 mm 2. Dead Load: Super Imposed dead load = 4.5 KPa (including slab weight) CHB = 3.11 KPa 3. Seismic Parameter: Soil Profile - Sb Closest distance to the source - 10 km Ductility Coefficient R = 8.0 Seismic Zone Z=0.40 Ct = 0.0731 A. Compute the DESIGN BASE SHEAR (V = Cv*I*W /R*T). B. Compute the Minimum DESIGN BASE SHEAR (V =0.11Ca*I*W).
Q2: Find the increase of the vertical total stress, and total stress at point Z. Q2 kN/m Q1 kN/m/meter 01-2100 Q2=10500 2=3.00 y dry 1m ydry-16.32
Direct Stress 25 kN 20 kN 30 kN B• C D А +1.5 m→ 3 m 3 m 1. The cross-sectional area of bar ABCD is 600 mm². Determine the maximum normal stress in the bar.
A concentrated load of 1000 kN is applied at the ground surface. Compute the vertical stress at a depth of 4 m below the load. Use Boussinesq's equation.equation. Select one: O a. 57.75 kN/m2 Ob. 17 kN/m2 Oc. 67 kN/m2 O d. 30 kN/m2
2- Point loads of magnitude 100, 200, 300 and 400 lbs. act at A, B, C, and D, respectively. Determine the increase in vertical stress at a depth of 6 ft below the point A. 6 ft B A 6 ft C D 3 ft
A rectangular distributed load of 100 kPa is applied to the soil surface. An additional circular distributed load of 200 kPa is applied on one side of the previous load. Determine the vertical effective stress 6 m below point A due to the application of both loads. R= 6 m 6 m 6 m 6 m 200 kPa 6 m 6 m 100 kPa 6 m
2 Refer to the soil profile shown in figure below CALCULATE TOTAL STRESS (ot) AT POINT B put of G.W.T Sand 5m Y sat = 20. 9 Clay 4m Ysat = 17. 8 Let the point A at depth "0", point B at depth "Sm". and point C at depth 9m Select one: Select one: O a. 102.3 KN/M2 Ob. 107 KN/M2 O c. 109 KN/M2 O d. 104.5 KN/M2 Next page evious page