Question A4 Two long, silver rods (k = 400 W/mK, diameter = 10 mm) are solderedtogether end to end, with the solder having a melting point of 520°C.The rods are in air at 20°C with a convection coefficient of 10 W/m?K.Ignoring radiation, what is the minimum power input needed to completethe soldering? Comment on how including radiation would haveaffected your calculated estimate of power needed for the soldering.

When an amount of heat is supplied from the one solid body to the another solid body due to…

Two long, silver rods (k = 400 W/mK, diameter = 10 mm) are soldered together end to end, with the solder having a melting point of 520°C. The rods are in air at 20°C with a convection coefficient of 10 W/m2K. Ignoring radiation, what is the minimum power input needed to complete the soldering? Comment on how including radiation would have affected your calculated estimate of power needed for the soldering.

Two long, silver rods (k = 400 W/mK, diameter = 10 mm) are soldered together end to end, with the solder having a melting point of 520°C. The rods are in air at 20°C with a convection coefficient of 10 W/m2K. Ignoring radiation, what is the minimum power input needed to complete the soldering? Comment on how including radiation would have affected your calculated estimate of power needed for the soldering.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Aluminum strips of 2 mm thickness are joined together by resistance spot welding process by applying an electric current 6000 A and 0.15 second. The heat required for melting aluminum is 2.9 J/mm3. The diameter and thickness of the weld nugget are found to be 5 mm and 2.5 mm respectively. Assuming the electrical resistance to be 75 micro ohms, the percentage of total energy utilized in forming the weld nugget is (a) 28 (c) 65 (b) 35 (d) 72
Resistance spot welding is performed on two plates of 1.5 mm thickness with 6 mm diameter electrode, using 15000 A current for a time duration of 0.25 seconds. Assuming the interface resistance to be 0.00010, the heat generated ( W-sec) to form the weld is
Two 1.2 mm thick sheets of steel are joined by double-sided spot welding using a current of 6000A and current flow time of t = 0.15 sec. The electrodes are 3 mm in diameter and the weld spot thickness is approximately one third of the total thickness of the metal sheets. Assuming that the effective resistance in this operation is 200 micro resistance, estimate the heat generated and its distribution in the weld zone. (Take density of steel = 8600 Kg/m3 and its latent heat capacity, L =1400 J/g)
A U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U-groove is prepared using a milling cutter so the radius of the groove is 3.0 mm. During welding, the penetration of the weld causes an additional 1.5 mm of material to be melted. The final cross-sectional area of the weld can be approximated by a semicircle with a radius of 4.5 mm. The length of the weld is 200 mm. The melting factor of the setup is 0.57 and the heat transfer factor is 0.86. (a) What is the quantity of heat (in Joules) required to melt the volume of metal in this weld (filler metal plus base metal)? Assume the resulting top surface of the weld bead is flush with the top surface of the plates. (b) What is the required heat generated at the welding source?
Although many pots and pans are made of stainless steel, the bottoms often have either a roll-bonded layer of pure copper (Cu) or a brazed or embedded disk of pure aluminum (Al). Use material property values to explain why this design approach leads to more uniform heat dispersal across the bottom of the pan (reducing ‘hot spots’ during cooking).
A U-groove weld is used to butt weld 2 pieces of 7.0-mm-thick titanium plate. The U- groove is prepared using a milling cutter so the radius of the groove is 3.0 mm. During welding, the penetration of the weld causes an additional 1.5 mm of material to be melted. The final cross-sectional area of the weld can be approximated by a semicircle with a radius of 4.5 mm. The length of the weld is 200 mm. The melting factor of the setup is 0.57 and the heat transfer factor is 0.86. Tm for titanium is 2070°K (a) What is the quantity of heat (in Joules) required to melt the volume of metal in this weld (filler metal plus base metal)? Assume the resulting top surface of the weld bead is flush with the top surface of the plates. (b) What is the required heat generated at the welding source?
Two 3.5 mm thick metal (Um = 9.5 J/mm?) sheets are being joined using resistance spot welding. To achieve required strength, it is desired to form a weld nugget that is 5.5 mm in diameter and 4.0 mm thick. The weld duration will be set at 0.3 sec. If the electrical resistance between the surfaces is 140 microohms, and only onethird of the electrical energy generated will be used to form the weld nugget determine the current.
A fillet weld on low carbon steel has a cross‑sectional area of 25.0 mm2 and is 900 mm long. Determine (a) the amount of heat required to perform the weld, and (b) the amount of heat that must be generated by the heat source, if the heat transfer factor = 0.90 and the melting factor = 0.60?
An electron-beam welding operation will join two pieces of steel plate together. The plates are 2.5 cm thick. The unit melting energy is 8050 J/cm3. The diameter of the work area focus of the beam is 0.15 cm, hence the width of the weld will be 0.15 cm. The accelerating voltage is 30 kV and the beam current is 35 milliamp. The heat transfer factor is 0.70 and the melting factor is 0.55. If the beam moves at a speed of 125 cm/min, will the beam penetrate the full thickness of the plates
A corner fillet weld with cross sectional area of 75 mm is made using oxyacetylene welding. Material of the welded plates is low carbon steel (Um = 10.3 J/mm'. Travel speed at which the bead is formed = 5 mm/s. Assume that only 40% of the energy generated by the torch is used for melting the metal; the rest is dissipated. If heat of combustion for acetylene is= 54.8 MJ/m³ , determine the volume flow rate of acetylene required to perform this OAW operation.
An arc welding operation on nickel performs a groove weld, whose cross-sectional area = 20.0 mm2. The melting point of nickel Tm = 1725° Travel velocity = 4.0 mm/sec. Heat transfer factor = 0.82, and melting factor = 0.70. Determine the rate of heat generation required at the welding source to accomplish this weld.
An RSW operation is used to join two pieces of sheet steel having a unit melting energy of 8369.85 J/cm3. The sheet steel has a thickness of 0.3125 cm. The weld duration will be set at 0.25 sec with a current of 11,000 amp. Based on the electrode diameter, the weld nugget will have a diameter of 0.75 cm. Experience has shown that 40% of the supplied heat melts the nugget and the rest is dissipated by the metal. If the electrical resistance between the surfaces is 130 micro-ohms, what is the thickness of the weld nugget assuming it has a uniform thickness?