Two steel plate tension members have been connected using 0.72 inch diameter bolts arranged in an equally-spaced 9 by 3 rectangular formation. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 51.2 ksi, clear distance for each edge bolt as 0.12 in, and the clear distance for the other bolts as 1.072 in. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load and live load assuming live load is half as much as dead load. Consider ASD.

Two steel plate tension members have been connected using 0.72 inch diameter bolts arranged in an equally-spaced 9 by 3 rectangular formation. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 51.2 ksi, clear distance for each edge bolt as 0.12 in, and the clear distance for the other bolts as 1.072 in. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load and live load assuming live load is half as much as dead load. Consider ASD.

Architectural Drafting and Design (MindTap Course List)

7th Edition

ISBN:9781285165738

Author:Alan Jefferis, David A. Madsen, David P. Madsen

Publisher:Alan Jefferis, David A. Madsen, David P. Madsen

Chapter28: Structural Components Of Framed Construction

Section: Chapter Questions

Problem 28.34Q

See similar textbooks

Similar questions

Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. a)Sketch the connection showing all the details and measurements with units. b)Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 150 mm x 90 mm x 12 mm angular section is welded to a gusset plate as shown. Area of the angle is 2736 sq.mm, allowable shear Fv is 150MPa, Allowable tensile stress Ft = 0.6Fy with Fy = 250 MPa. Questions: a) Design force P b) Total required length of weld using 12 mm fillet weld c) Value of “b”
Compute the available block shear strength of the gusset plate and design tension strength. 2 in A- B- D 3 in El F. 2 in 0.375 in 0.375 in 2 in 3 in 3 in 2 in (not to scale) Section properties Material properties plate width = 7 in ASTM A36 steel plates plate thickness =/s in F, = 36 ksi %3D standard hole size F,= 58 ksi
The diagonal at the left to the connection is a double angle 90 mm x 90 mm x 8 mm, with area of 2700 mm?, bolted to the 8 mm thick gusset plate. Bolt diameter = 16 mm Bolt hole diameter = 18 mm Bolt bearing capacity, Fp = 480 MPa Bolt shear strength, Fv = 68 MPa Steel plate strength and stresses are as follows: Yield strength, Fy 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 0.60 Fy Allowable tensile stress on the net area = %3D 0.50 Fu Allowable shear stress on the net area = 0.30 Fu Bolt bearing capacity, Fp = 1.2 Fy Calculate the allowable tensile load, P(kN) under the following conditions: %3D
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem A lap joint is made up of two steel plates 225mm by 10mm. It is connected by seven rivets having a diameter of 22mm snug fit in the drilled holes. The allowable stresses in the rivets and plates are 110 MPa in shear, 220 MPa n bearing and 138 MPa in tension. Use LRFD. Questions: a) Determine the nominal strength for one bolt due to shear. b) Determine the capacity of the plate based on the gross area and effective area.
Two steel plate tension members have been connected using 0.72” diameter bolts arranged in an equally-spaced four by four square formation.Total plate self-weight is specified as 912 pounds.Design of the elements adhered to the set of values that are twice as much as the minimum requirements. Both plates have a thickness equal to 1/3 in. Take shear fracture stress as 54ksi and the min required edge distance as 0.125ft. Find the maximum allowable service dead load(excluding the self-weight)and live load assuming live load is half as much as dead load including the self-weight of the plates.
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
2. A steel plate is 360 mm wide and 20 mm thick with four bolts hole into the place as shown in the figure. Compute the following: a. Critical net area required by the NSCP specs. b. Max. critical net area required by the NSP specs. Note that, Max. net area is 85% of the critical net area c. Capacity of the joint if the allowable tensile stress is 0.75Fy. Use A36 steel Fy=248 MPa 90m²m 90 mm 90mm 45 45mm In my comin P Scanned with CamScanner CS
A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572 Grade 50 plate material has a width of 150 mm and thickness of 16 mm. Assume diameter hole to be 24 mm. Bolt threads are excluded from the shear plane. Allowable stress of A 325 bolts: Fv = 207 MPa Fp = 1.5 Fu (to prevent excessive hole deformation) Allowable stresses of A572 Grade 50 plate material: Fy = 345 MPa Fu = 450 MPa a. Compute the tensile capacity due to the failure of the plates. b. Compute the tensile capacity due to the failure of the bolts.