Use A992 steel and select a W12 shape for an axially loaded column to meet the following specifications: The length is 24 feet, both ends are pinned, and there is bracing in the weak direction at a point 10 feet from the top. The service dead load is 142 kips, and the service live load is 356 kips. a. Use LRFD

Use A992 steel and select a W12 shape for an axially loaded column to meet the following specifications: The length is 24 feet, both ends are pinned, and there is bracing in the weak direction at a point 10 feet from the top. The service dead load is 142 kips, and the service live load is 356 kips. a. Use LRFD

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter4: Compression Members

Section: Chapter Questions

Problem 4.7.3P

See similar textbooks

Similar questions

If the beam in Problem 5.5-9 i5 braced at A, B, and C, compute for the unbr Cb aced length AC (same as Cb for unbraced length CB). Do not include the beam weight in the loading. a. Use the unfactored service loads. b. Use factored loads.
A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
The beam under the Live and Dead loads is shown below. The steel class is $235. Lig L1 L2 a.) Evaluate the slenderness of the web and flange. b.) Calculate the Cb value based on the loads. c.) Calculate the bending moment capacity of the beam... d.) Is the beam cross-section enough for the given loads. L3
SITUATION 2 Determine the safe service load W permitted for this beam-column that is not part of a frame system. Assume ASTM A992 (Fy = 350 MPa; Fu = 450 MPa) as material. Use LRFD specifications. Servise koada P= 30 kips dead load 80 kips live koad Assume hinged for both principal 10- 0 directions W- 20 dead load 8OG live load 10-o Fined for both principal directions Type your final answer/s in the text box provided below.
Q2) The members of the truss structure shown below is plain concrete. The compressive strength of the concrete is 25 MPa. Compute the maximum load P that can be carried by the structure. (Cross section of each member of the truss is 200 x 200 mm and don't use material factors and do not consider slenderness) Comment on your results briefly. P A& 2m SC 2 m 1380 2m D
The beam shown in Figure is a two-span beam with a pin (hinge) in the center of the left span,making the beam statically determinate. There is continuous lateral support. The concentratedloads are service live loads. Determine whether a W12 × 79 of A992 steel is adequate.a. Use LRFD.b. Use ASD.
Use 2015 NSCP A simply supported beam is subjected to a uniform service dead load of 1.0 kip/ft(including the weight of the beam) a uniform service live load of 2.0 kips/ft and a concentrated service dead load of 40 kips. The beam is 40ft long and a concentrated load is located 15 ft from the left end. The beam has continuous lateral support and A36 steel is used. Is W30x108 adequate? a) Use LRFD b) use ASD P₁=40* -15- 25'- WD = 1.0km W₁ = 2.0³m W30 x 108 40'-
Use A992 steel and select a W14 shape for an axially loaded column to meet the following specifications: The length is 22 feet, both ends are pinned, and there is bracing in the weak direction at a point 10 feet from the top. The service dead load is 142 kips, and the service live load is 356 kips. a. Use LRFD. b. Use ASD.