Use the two circuits given below to design a band-pass active filter (Find the values of R₁, R2, RA, RB, C₁, and C₂) with a center frequency fo = 40kHz and bandwidth =20kHz and the voltage gain Av = 40 for each circuit and assume R₁ = 19RB. 1) Draw your design circuit for a band-pass active filter. 2) Draw its frequency response and indicate all information. 3) Determine the cut off frequencies (f₁ and f) that indemnify the bandwidth. 4) Identify the number of poles in the whole circuit.

Use the two circuits given below to design a band-pass active filter (Find the values of R₁, R2, RA, RB, C₁, and C₂) with a center frequency fo = 40kHz and bandwidth =20kHz and the voltage gain Av = 40 for each circuit and assume R₁ = 19RB. 1) Draw your design circuit for a band-pass active filter. 2) Draw its frequency response and indicate all information. 3) Determine the cut off frequencies (f₁ and f) that indemnify the bandwidth. 4) Identify the number of poles in the whole circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What is a bandpass filter? How is its bandwidth defined?
The active high pass filter is given below. Determine the R value to make the gain at low frequency range (Stop band frequency) 0dB. In addition, determine the C value for a pole value of (pole = 10*zero). With those R and C values, find the transfer function (Vo/Vin) and bode plot for the magnitude.
Design a single pole low pass filter with a gain of 10 in the passband and a 3dB frequency of 5kHz. The minimum resistance in the passband for this filter is to be of 10k-ohms. What is the value of C in nF and in two decimal places only.?
What is the transfer function of a filter? Describe how the transfer function of a filter can be determined using laboratory methods.
6. The response of a band rejected filter is characterized in — — — — —. 4 . c
Design a first order active low pass filter using a single ideal Operational Amplifier (Op-Amp) as follows: a) Draw the circuit diagram of the filter. b) Derive the transfer function of the filter.
a)Draw a general graph showing its gain verses frequency with gain in dB vs log of frequency and indicate the cut-off Frequency. b) Draw a simple, single resistor, single capacitor high pass filter. What is the formula for the cut-off frequency for this filter? c) Draw a graph of its gain verses frequency and label its cut-off frequency.
For a given transfer function of a bandpass filter circuit as shown in the figure For a given transfer function (Take K as 1) Find the center frequency, band-with and the gain for this bandpass filter. 2.Find the cut-off frequencies and the quality for this filter
Show that the circuit behaves as a bandpass filter.(Hint—find the transfer function for this circuit and show that it has thesame form as the transfer function for a bandpass filter. 1. Find the center frequency, bandwidth and gain for this bandpassfilter.2. Find the cutoff frequencies and the quality factor for this bandpassfilter.
5. Why we use semiology paper to draw the frequency response of filters. 6. What is filter order, and what is the effect of changing filter order on the filter response and complexity of filter. 7 Sketch the frequency response of low-pass, band-pass, high-pass, and band-reject filters.
filter specification a. What kind of filter is this? b. What is the transition band of the filter is given as ₂ = 0.4, , = 0.5, ₁ = 0.01, &₂ = 0.00001, c. Draw the absolute specification d. What is the specification in relative? e. Draw the relative specification. f. If the filter is applied on a signal sampled at 100 kHz, what are the frequency edges in Hz?
A) Write the equation for the small-signal gain function Vout/Vinfor the followingop-amp circuit B) What kind of filter is this circuit? C)Write the equation for the cutoff frequency of the filter D) Sketch the Frequency Response of the system