Water at 25°C is flowing in a 26 cm commercial steel pipe. The total length of the pipe is 1416m. If a head of water of 11.3 m is available to overcome the friction loss, what should be the volumetric flow rate of the water flowing in the pipe in m³/hour? Use density data from Handbook, viscosity = 1cP. The flow is turbulent. In 2 decimal values.

Water at 25°C is flowing in a 26 cm commercial steel pipe. The total length of the pipe is 1416m. If a head of water of 11.3 m is available to overcome the friction loss, what should be the volumetric flow rate of the water flowing in the pipe in m³/hour? Use density data from Handbook, viscosity = 1cP. The flow is turbulent. In 2 decimal values.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1-A steel discharge pipe with a roughness equal to 0.5 mm is 800 m long and pumps 265 m³ of water per hour at a temperature of 20°C. The pipe diameter is 25 cm. Calculate the head loss. Data: kinematic water viscosity equal to 10-6 NOTE: if necessary, use Moody's DiagramHelp?
A fluid is being pumped through a pipe. The density of fluid is 872 kg/m³. The viscosity is 2.8x102 Pa.s. The velocity in the pipe is 5.9 m/s. If the Reynolds number is 2100. a- What is the pipe cross-sectional area? b- If the pipe cross-sectional area increased 1.5 fold under same Reynold number, density and viscosity, what is the new velocity?
Show complete solution. Units must be included in all calculations. All numerical values should be rounded off to the nearestthousandths. 3.At section 1 of a pipe system carrying water the velocity is 3.0 fps and the diameter is 2.0 ft. At section 2 thediameter is 3.0 ft. Find the discharge and velocity at section 2.
In shut off valve experiment, the 3/ 6th of valve position, the discharge is found as of 6 lit/s for the 27mm diameter pipe. Find the velocity and Reynolds number of the flow. Take the viscosity of water as 1.14x10 Ns/m?. (Enter only the value in the box by considering the unit given in bracket. Do not write the unit in the boxes) Velocity of water (unit in mm/s) = Reynold's number
Solve and Draw the figure completely labelled with all the notations used in your solution. A 50 mm Venturi meter (C = 0.98) is installed in a 75 mm diameter horizontal pipe carrying oil having specific gravity of 0.83. If the recorded flow in the meter was 25 liters per second, what could have been the deflection of water in the differential manometer connected between the inlet and the throat?
7. The head loss of a 669 m length of tube having a diameter of 26 mm is 52 m. Oil flows through the tube at a Reynolds Number of 1919. Compute the kinematic viscosity of the fluid in m2/s. Round your answer to 7 decimal places.
Directions: Solve the following problems completely, and make a detailed solution. Any incompletesolution arriving at such answers will never be considered. A 1124gpm of water is flowing in a round pipe such that the flow remains laminar.What is the diameter of the pipe in inches necessary to ensure laminar flow? Usekinematic viscosity of 4398 stokes.
Air at 68 degrees Celsius is being pumped through a pipe of internal diameter 6.4 inches. If the volumetric flow rate has been set to 6.2 cubic feet per minute, determine if the flow is laminar or turbulent. Assume pressure is atmospheric. Use the data for air viscosity given below. * C = 1.425 x 10-6 C2 = 0.5039 C3 = 108.3 CTC C3 C4 T2 H[Pa s] 1++
Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.. A cylindrical tank 5 ft high has a constant diameter of 4 ft is full of water. The tank has a hole2. A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a holein its bo]om that measures 0.1ft^2. All losses are insignificant. How long will it take for the tankto empty? Note that you can NOT assume a staLc head and constant flow rate because thewater head in the tank decreases as the water flows out of the tank (A) 35 sec(B) 70 sec(C) 105 sec(D) 140 sec
1. Solve the following and draw the figures Í. A 30 cm x 15 cm venturimeter is inserted in a vertical pipe carrying water, flowing in the upward direction. A differential mercury manometer connected to the inlet and throat gives a reading of 30 cm. Find the [Ans. 154.02 lit/s] ii. If in the problem 13, instead of water, oil of sp. gr. 0.8 is flowing through the venturimeter, determine the [Ans. 173.56 lit/s] III. The water is flowing through a pipe of diameter 30 cm. The pipe is inclined and a venturimeter is inserted in the pipe. The diameter of venturimeter at throat is 15 cm. The difference of pressure between the inlet and throat of the venturimeter is measured by a liquid of sp. gr. 0.8 in an inverted U-tube which gives a reading of 40 cm. The loss of head between the inlet and throat is 0.3 times the kinetic head of the pipe. [Ans. 22.64 lit./s] discharge. Take Ca = 0.98. rate of flow of oil in litres/s. Find the discharge.
B1. A water with viscosity 11.4x103 poise is flowing through a pipe of diameter 300 mm at the rate of 375 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1.5 km. The velocity of flow of water (in m/s) is The value of Reynold's Number is The frictional loss in the pipe (in m) is
Air at 68 degrees Celsius is being pumped through a pipe of internal diameter 6.4 inches. If the volumetric flow rate has been set to 6.2 cubic feet per minute, determine if the flow is laminar or turbulent. Assume pressure is atmospheric. Use the data for air viscosity given below. c1 = 1.425x10^-6 c2 = 0.5039 c3 = 108.3