Water flows from a lake as is shown in the Figure at a rate of 4 cfs. Is the device inside the building a pump or a turbine? Explain and determine the horsepower of the device. Neglect all minor losses and assume the friction factor is 0.015.

Water flows from a lake as is shown in the Figure at a rate of 4 cfs. Is the device inside the building a pump or a turbine? Explain and determine the horsepower of the device. Neglect all minor losses and assume the friction factor is 0.015.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure 5 shows a pump connected to a large tank of water. Water flows out of the tank through the pump into a galvanized iron pipe of diameter D = 80 mm at a length, L = 40 m. At the end of the pipe, water exits through a nozzle of diameter D2 = 50 mm. With the height of water h, the pump adds 30 kW of power to the water resulting in a volumetric flowrate of Q=0.05 m³/s. Ignore the length of the nozzle and assume that the velocities are uniform. By using the same height of water and pipe, explain and justify with your calculation, which parameter(s) will be affected if the pump is to be removed from the system. ♡ (1) D2 = 50 mm h (2) Ритp L= 40 m D= 80 mm Figure 5
The figure shows a portion of a fire protection system in which a pump draws water at 60°F(v=1.21 x10-5 m² from a reservoir and delivers it to a point B at the flow rate of 1500 gal/min. Calculate the required height of the the water level in the tank in order to maintain 5.0 Psig pressure at point A
With the valve closed, water flows from tank A to tank B as shown in the figure below. What is the flowrate into tank B when the valve is opened to allow water to flow into tank C also? Neglect all minor losses and assume that the friction factor is 0.02 for all pipes. Assume ZA = 17 m. Q = i Elevation = ₁ Diameter of each pipe= 0.10 m -80 m- m³/s 40 m- 75 m- Elevations =
The centrifugal pump in the figure pumps the water at 25°C from the tank 1.22 m above its inlet center. The inner diameter of the suction pipe is 101.6 mm, the coefficient of friction is 0.0306 and the length is 3.2 m. The sum of the local loss coefficients of the elements in this pipe is 7.4. If the pump operates at a flow rate of 109 m3/h, ENPY=1.52 m. Does the pump work without cavitation at this flow rate? Show the calculation. For water, p-997 kg/m3 and Pb-3.169 kPa. Patm=101.3 kPa and a2-1.05. Depo 80.a Girişteki borulama Pompa sistemi Vana m Ya9
Water is transported in a pipe, at an average flow rate of Q = 50 L/s. Calculate the pressure difference p between the 2 manometers. We can assume that the energy losses by friction are negligible, and that there are only singular energy losses (be careful to identify ALL the singularities). The pump adds an energy of HP = 10 m to the system. "GATE VALVE" P2 OUVERTURE COMPLÈTE do = 150 mm Q = 50 L/s • 2) 2 m Q = 50 L/s COUDES À POMPE RAYONS COURTS do = 150 mm (Hp = 10 m)
Oil with a specific gravity of 0.86 is Pz= 43 psi being pumped from a reservoir as shown in the figure below. The 3 ft Pump pressures at points 1 and 2 are -4.0 psi and 43.0 psi, respectively. The flow rate in the pipe is 0.50 ft3 /s. The pump is rated at 8 hp. Determine the NPSH. Neglect frictional losses in the system.
A water pump is used to pump the water to a large water tank as shown in Figure. The free surfaces of both water tanks are under atmospheric pressure. Dimensions and local losses are given below. The flow rate of the pump is determined as 16.2 L/min. Calculate the required manometric head of the pump and the required motor power if the total efficiency is 76.2 percent. The water at 10oC. density r = 996.2 kg/m3, dynamic viscosity µ = 1.362x10-3kg /ms. z2-z1 = 7.62 m (height difference), D = 2.62 cm (pipe diameter), L = 176.2 m (total pipe length), ɛ = 0.2562 mm (pipe roughness value) Local loss coefficients: KL,inlet = 0.562 (pipe inlet) KL,valve = 16.2 (valve), KL,elbow = 0.9262 (there are 5 elbows totally in pipe line), KL,outlet = 1.0562 (pipe outlet).
2. Water at 10 C is flowing 10 points from point A to point B through the pipe, as shown in the figure, at the rate of O.37 m3/s. If the pressure at A is 66.2 kPa, determine the pressure at B, in kPa, assuming no frictional losses. 600-mm inside diameter 4.5 m Flow 300-mm inside diameter
With velocity of 10 m/s in the 347 mm diameter pipe in the figure shown, determine the discharge in pipe 3 in m3/s. Assume f = 0.034 for all pipes and neglect minor losses. The following are the properties of each pipe: Pipe 1 (Length=345 m, Diameter = 347 mm) Pipe 2 (Length=477 m, Diameter = 571 mm) Pipe 3 (Length=598 m, Diameter = 665 mm) Pipe 4 (Length=710 m, Diameter = 380 mm) Pipe 5 (Length=823 m, Diameter = 594 mm)
Two reservoirs with top surfaces placed on the flat ground and connected with each other with a straight pipe and pump system. The height of the first reservoir is Z1=10 m and the second reservoir is Z2=30 m from the ground level. The pump sucks water from the first reservoir and conveys into the second reservoir. The major head loss along the pipe is hf=40 m with ignoring local head losses. Calculate the manometric head of the pump in a meter of water.
What is the minimum power required from the pump to deliver the oil from Reservoir A to Reservoir B as shown in Figure 2 at a rate of 0.30m³/s? The pump has a 70% efficiency rating. V Reservoir A -Oil v= 10-5 m²/s p=950kg/m³ Elevation 135m Steel Pipe, ks =0.046mm, L= 200m, D=250mm Elevation 120m r/D=0.1 Pump Figure 2 r/d=1 Reservoir B abrupt Globe valve, wide open Air at 200kPa Elevation 110m Elevation 100m
A pump draws 24 li/s of water from the lower reservoir and lifts it to upper reservoir. The head lossfrom the inlet 150 mm pipe diameter is three times the velocity head and the head loss going to theoutlet 100mm pipe diameter is 25 times its velocity head. What is the power generated by the pump tothe system in horsepower. (Note: Velocities from the reservoir are different from the velocities of thepipe and pleaseee draw a diagram if you can thank you so much)