- What is conductor connection of exposed conductive parts (chassis) of machines and/or devices with the neutral line
Q: i) An overhead transmission line is supported at a river crossing by two towers of height 33 m. The…
A: As per Bartleby guidelines we are allowed to solve only three subparts, please ask the rest again.…
Q: . Which of the following statements about securing and protecting grounding electrode conductors is…
A: A) Ground elecrodes can be run through wood framings. Since wood being an insulator and doesn't hold…
Q: 1. _______ is not considered an effective ground-fault current path. a) Ground b) Equipment…
A: Choose the correct option 1. _______ is not considered an effective ground-fault current path. Fill…
Q: Select the right answer of the following: 1- The 66 Ky lines use (pin insulators/suspension…
A:
Q: 20. A separately derived system is an electrical source, other than a service, having ____…
A: Separately derived power system is an electrical power system where power is generated from battery…
Q: (ii) An overhead transmission line is supported at a river crossing by two towers of height 35 m.…
A: The weight, sag, and length of the conductor is determined as shown below
Q: Code: COFFEE. A single-core cable has a conductor diameter of 13.5 mm and insulation thickness of…
A: For a single−core cable, The diameter of the conductor is,d=13.5 mm The thickness of the…
Q: A 2-wire d.c. distributor cable AB is 2 km long and supplies loads of 100A, 150A,200A and 50A…
A: It is a two wire distribution system with distributor fed at one end: Here, the distributor is fed…
Q: Expansion fittings and telescoping sections of metal raceways shall be made electrically continuous…
A: In Bonding loosely jointed metal raceways, grounding electeode and grounded current carrying…
Q: an unintentional electrically conducting connection between and ungrounded conductor of an…
A: The fault occurs due to connection between the ungrounded conductor and the metallic raceways,…
Q: Overhead Conductors used as Transmission Lines are always thickly insulated. Select one: True False
A: The overhead conductors used for transmission lines are generally ACSR (Alluminium Core Steel…
Q: With respect to conductor insulation, describe the following location ratings: a. Dry b. Damp c. Wet
A:
Q: 3. The towers of height 35 m and 95 m respectively support a transmission line conductor at water…
A:
Q: 1.A. When a grounding electrode conductor is connected to the grounded conductor within a…
A: (1.A) According to Section 250.24(B) of National electricity code (NEC) , When ground electrode…
Q: explain and write the advantage and disadvantage of the following wiring system i. cleated system…
A:
Q: Discuss and compare the various method of neutral earthing
A: Different earthing methods are given below, 1. Underground neutral earthing : In ungrounded earthing…
Q: 10. Which of the following statements about ground faults is true? A. They usually occur between any…
A: Ground faults: It happens when an energized conductor develops an accidental contact with the…
Q: 3. A two conductor main A B, 500 m in length is fed from both ends at 250 volts. Loads of 50 A, 60…
A: The solution can be achieved as follows.
Q: (11) An overhead transmission line is supported at a river crossing by two towers of height 37 m.…
A: Given Given Two towers at same level h=37 m Wt. of conductor =W = 0.307 kg/m Wt due to wind =Ww =…
Q: Which of the following is not a criteria for the mechanical design of an overhead line? O Minimum…
A: over head lines are designed based on distance between conductor and earth , tensile stress ,…
Q: 1) What is the allowable ampacity of a single #2 THHN conductor that is installed in a conduit with…
A: It is asked to find the the allowable ampacity of a single #2 AWG THHN conductor that is installed…
Q: QUESTION 5 a) What is the difference between neutral and earth? b) Differentiate between…
A: In a three phase system, there are two ways to connect a three phase load. Star/Wye Connection.…
Q: 1. What is the proper size copper grounding electrode conductor for a 100-ampere service that…
A: Given-Rating of service conductor=100 ASize of phase conductor= 3/0 AWG
Q: The equipment grounding conductor of a grounding-type receptacle or a branch-circuit extension is…
A: True, The equipment grounding conductor of a grounding-type receptacle or a branch-circuit extension…
Q: 2.a. What's defined as an assembly consisting of a service raceway, guy wires or braces, service…
A: 2.a. Drip loops are used for preventing rainwater and moisture. Thus this is not a suitable…
Q: If the thickness of the insulating material in the problem with code COFFEE is increased by 30%,…
A:
Q: An overhead transmission line conductor consists of hard drawn copper conductor of diameter 15 mm,…
A:
Q: Restrictions on types of conduits used for installing service, sub panel, emergency service panel.
A: We are authorized to answer one question at a time, since you have not mentioned which question you…
Q: 10.a. Which of the following is a condition of the exception that allows the grounded conductor of…
A: According to guidelines we need to solve only first question. According to the question we have to…
Q: A- Discuss the following claimed arguments: 1- Guard rings are recommended in low voltage as…
A: 1) Guard ring Figure shows electrical equivalent circuit of insulator discs connected at tower.…
Q: A 2-wire d.c. distributor cable AB is 3 km long and supplies loads of 100A, 150A,200A and 50A…
A: We have a 2-wire D.C distributor cable with 3 Km long which supplies loads given A from feeding…
Q: An overhead line has a span of 150 m between level supports. The conductor has a cross-sectional…
A: We have an overhead line with the line parameters as, Line Span (l) = 150 m Cross-sectional area = 2…
Q: What is the percentage voltage drop for a 208V, three-phase feeder serving a load of 200A at a…
A: Given data, Voltage V = 208 V Load current i = 200 A Distance l=290 feet = 88.4 m For 4/0 copper…
Q: Which of the following criteria is correct for the mechanical design of the overhead line? Minimum…
A: Design parameters of design mechanical design of the overhead line.
Q: Define an equipment grounding conductor. The conductive path that part. of eftective an graund-fault…
A: Grounding is generally a direct physical connection to the earth. Electrical circuits are connected…
Q: • The cost of a 1-o overhead feeder is OMR 6 a per km ( a is area of cross section in sq mm) and the…
A: Given: The cost of a single-phase overhead feeder is OMR 6 a per km (a is the area of cross-section…
Q: Identify and describe the step-by-step procedure that is used to draw cable, as well as the…
A: It is asked to describe the step-by-step procedure that is used to draw cable and to install cable…
Q: A set of conductors is used to supply residential unit with a total load current of 60 A at a…
A:
Q: 16. A conductor installed from a bonding/grounding bushing that's used to provide a conducting…
A: A conductor installed from a bonding/grounding bushing that's used to provide a conducting…
Q: If the NEC provides a requirement to grounding equipment, it generally implies that there will be a…
A: Here we understand the concept related to grounding.
Q: 13. If the largest ungrounded service-entrance conductor for a service is 750-kcmil copper, what is…
A: Choose the correct option, If the largest ungrounded service-entrance conductor for a service is…
Q: Which of the following criteria is correct for the electrical design of the overhead line? O Tensile…
A: Need to find the criteria for Electrical design of overhead line
Q: 15 A certain type of Suspension Type Insulator is used to sustain heavy tensile loads of conductors…
A: Given that Suspension type insulator is used to sustain heavy tensile loads of conductors when the…
Q: 1. The only exception to the need for all information technology equipment to be satisfactorily…
A: Note: We are authorized to answer the first question since the exact one wasn’t specified. Please…
Q: What layer is used to smoothen the irregularity of the surface of the conductors of Underground…
A:
Q: LRT, 5 km distance from the Tayuma, takes 100 A over a 100 mm hard drawn copper trolley wire having…
A:
Q: Airframe Electrical System Question: Which wire installation type has the best rating and is the…
A: The wire installation type with best rating and most resistive to breakdown in a chemical…
Q: .a. There may be installations where grounded conductors of different systems are installed within…
A: Q.3) a) ans: (D) Since ground wire to be secured for any system , for different systems of any type…
Q: If a grounding electrode conductor is connected at the first system disconnecting means or…
A: As per the NEC [250.30(A)(3)], the system bonding jumper can be either installed at the separately…
Q: What size equipment grounding conductor is used with # 8 AWG nonmetallic-sheathed cable
A: The minimum size equipment grounding conductor is selected on the basis of the current rating…
1 - What is conductor connection of exposed conductive parts (chassis) of machines and/or devices with the neutral line?
A) Zeroing
B) Protection earth
C) Short circuit
D) System earh
E) Fuction earth
Step by step
Solved in 2 steps
- Question 1:a) State why voltage control and cable stranding are necessary in powersystemsb) Briefly explain where and how the following state variables ofa power supply grid are controlled.i) Frequencyii) Active powerili) Reactive poweriv Voltage.12 - Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters and three-wire cables up to ……... meters are used in standard designs. A) 10-150B) 40-500C) 50-195D) 30-230E) 200-1000c.1. Which of the following is one of the three essential functions of an equipment grounding conductor?A. Provide an arc-fault current pathB. Establish groundingC. Establish bondingD. Ensure the system is groundedc.2. What's another name for the three-point method of Earth resistance testing?A. Fall-of-potentialB. Line surgeC. Spatial shieldingD. Leakage current c.3. If the National Electrical Code provides a requirement to ground equipment, it generally implies thatthere will be a direct connection to the Earth of a connection through a/anA. grounding electrode conductor.B. equipment grounding conductor.C. equipotential bonding conductor.D. bonding conductor.
- low voltage systems What is the system called if current flows through its neutral conductor? a)Balanced b)Unbalanced c)Proactive d)ComplexA DC is supplied through a solid conductor cable. The fault in the cable can be determined by using Murray Loop Test. The healthy cable has the insulation resistance of 1 kilo Ohms per meter. No fault occurred till the first 10 km. The core of healthy cable has the circumference of 7.86cm. If the resistivity of insulation is 900 G Ohm-mm, what is the diameter of the cable.A set of conductors is used to supply residential unit with a total load current of 60 A at a single-phase supply voltage of 230 V. What would be the minimum size of the conductor to be used to achieve at least 5% voltage drop? The total conductor length is 300 ft. ..
- Count the neutral conductor of a 4-wire, 3-phase, wye-connected circuit when the major portion of the load is electric discharge lighting (fluorescent, mercury vapor, high-pressure sodium, etc.), data processing, and other loads where the neutral conductor carries a. grounding b. traveler C. d. current. third harmonic unbalanced conductors to overheat but often overlooked is the possibility ofUnderground service conductors shall have [Fill-in-the-blank]. A)adequate mechanical strength. B)sufficient ampacity for the loads calculated. C)none of these. D)adequate mechanical strength and sufficient ampacity for the loads calculated.A power generation plant connected to bulk load of high voltage industries shown in Figure Q3 has specifications given in Table Q3. Each equipment reactance is expressed in per unit on a common base of 100 MVA. a) Find the fault level for each bus bar in the generation plant. GI G2 TI Figure Q3: Single line diagram of a power generation plant Table Q3: Specifications of power system components Power System Component Voltage Rating X MVA Rating (kV) (pu) GI 50 33 0.2 G2 40 33 0.18 50 33/11 0.1 T2 40 33/11 0.1
- Which of the following is not a criteria for the mechanical design of an overhead line? O Minimum distance between conductor and earth O Maximum clearance between the conductor and ground O Tensile stress of the conductor O Thermal capacity of the conductor must be adequateh.1. In an alternating-current system, the maximum size for a copper grounding electrode conductor isA. 250 kcmil.B. 3/0.C. 500 kcmil.D. 4/0. h.2. The figure shows a fault condition in an ungrounded electrical system. Which of the following will occurbecause of the fault in this system?A. Only the overcurrent protector at Point A will trip open.B. The ground fault will heavily damage the service.C. Nothing will happen until a second ground fault occurs.D. The overcurrent protection will trip, shutting off all the line side power.3. The three bus-bar conductors in an outdoor sub-station are supplied by units ofpost insulators. Each unit consists of a stack of 3-pin insulators fixed one on the top of the other. The voltage across the lowest insulator is 8-45 kV and that across the next is 7-25 kV. Find the bus-bar voltage of the station. [38-8 kV]