What is the area of the tube?What is the total length of the median line?The shearing stress value will be.The angle of twist result is. An aluminum tube with the cross sectionshown has a constant wall thickness of 2mm. A torque T = 400 N-m is applied to%Dthe tube. Use G= 28 GPa *40 mm10 mm40 mm

As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked.…

Answered: What is the area of the tube? What is…

Engineering

Mechanical Engineering

What is the area of the tube? What is the total length of the median line? The shearing stress value will be

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter11: Columns

Section: Chapter Questions

Problem 11.3.10P: Repeat Problem 11.3-9. Use two C 150 × 12.2 steel shapes and assume that E = 205 GPa and L = 6 m.

See similar textbooks

Related questions

Q: A 450kN force is needed to punch a 30mm diameter hole in a plate that is 10mm thick. Determine the…

Q: The ultimate shearing stress of the plate is , = 300 MPa The compressive stress in the punch is o̟ =…

A: The ultimate shear stress for the plate is given as 300 MPa; the thickness of the plate is given as…

Q: Mang Inasal is working on a 300-mm solid shaft in his machine shop. He plans to subject the said…

Q: If the allowable stress of a revolving steel is 150 MPa, what is the equivalent angular velocity…

A: Write the formula for allowable stress of a revolving ring. σ=ρω2d24 Here, σ is the allowable…

Q: shop plans to subject the said shaft on a loading condition as shown in the figure. If the shearing…

Q: Do the stress concentrations exist on a shaft?

A: Stress concentration is increase in stress at particular point where stress is more because of hole…

Q: Prove that: in square key, the crushing stress is equal to twice of shearing stress.

Q: Design a hollow steel shaft to transmit a torque of 13,000 lb-in. The allowable shear stress in the…

Q: thin rectangular plate is uniformly deformed as shown below. Compute the shearing strain at P…

A: Solution is attached below:

Q: During the rolling process using 50 rev/min, it found that the torque is 22,000 N.m, Calculate the…

A: N( Revolution) = 50 rpm T( Torque) = 22000 Nm Formula for power P =(2πNT) /60

Q: For the figure below, the average shearing stress in each rivet is .kPa (Hint: Two 22-mm-diameter…

Q: What is the area of the tube? What is the total length of the median line? sheari

Q: During drawing process, using the Ao=5mm2, Af =4 mm2, K=200 MPa and n = 0.20, the average flow…

Q: A circular shape blank will be cut of 100+ 10 N mm diameter from a strip of 2.8+ 100 mm with a…

A: given diameter of circular blank to be cut, db=101 mmstrip thickness, t=2.9 mmclearnace, C=0.25…

Q: W310 x 52 beam is made with a material that has a maximum shearing stress of 90 MPa. Determine the…

Q: How can we determine the maximum shear stress in the shaft?

A: Torsional shear stress is the stress set up a member when it is subjected to two equal and opposite…

Q: Calculate the force required to shear a 0.7" dia. hole through a 0.16" thick piece of yellow brass.…

A: Given data: The diameter of the hole is d = 0.7 in. The thickness of the plate is t = 0.16 in. The…

Q: A 10-spline shaft ( d= 0.91D, w= 0.156D, h= 0.045D ) and permanent fit has a diameter of 70 mm. Find…

Q: Home Work: 1. As shown in figure below, a hole is to be punched out of a plate having an ultimate…

Q: Derive the expression of shear plane angle. Draw and mention all corresponding angle required for…

Q: Compute the torque necessary to twist a 3/8 inch diameter solid rod of rolled brass, 12 inches long,…

Q: Prove the formula for Hoop stress and longitudinal stress and also explain poisson ratio.

A: Given Data⇒ Hoop Stress Longitudinal Stress Poisson ratio

Q: find the smallest diameter bolt that can be used in the clevis P=400KN shearing strength of the…

Q: n a wire drawing operation diameter of a steel wire is reduced from 10 mm to 8 mm .The mean flow…

A: Given:Initial diameter of steel wire, Di=10 mmFinal diameter of steel wire, Do=8 mmThe mean flow…

Q: A torque of 2.5 kN.m is applied to the hollow, thin- walled, aluminium section shown in Fig. 3.18.…

A: As illustrated in the picture in the question, a torque of 2.5 kN.m is given to the hollow,…

Q: The maximum safe compressive stress in a hardened steel punch is limited to 1 GPa and the punch is…

Q: For the figure below, the average shearing stress in each rivet is ..kPa

Q: A 48 inches diameter saw blade is mounted on a pulley driven steel shaft, requiring a blade…

A: Given:- ds=48 inVs=150 ft/sPb=150 ft/secNb=1200 rpmdpB=6 inTo find:-Diameter of the shaft

Q: Calculate the shearing force (kN, rounded off to the nearest whole number) needed for a blanking…

A: The shearing force is given by, Fshear=0.7×σu×T×L where, T = sheet thickness = 2.5 mm L = total…

Q: Calculate the maximum shearing force that a hollow rivet with inside and outside diameters of 4 mm…

Q: (a) A solid shaft of 220 mm dia is to be repiace dia being 2:1. Find the size of hallow shaft, if…

A: The shear stress developed in a solid shaft due to applied torque T is given by the formula-…

Q: A coupling is used to connect a 51mm diameter plastic rod to a 35mm diameter rod as shown. If the…

Q: horizontal shearing stress?

A: Using shearing stress of beam formula we have calculated. detailed solution given below

Q: In a slab rolling operation, the maximum thickness reduction (del hmax) is given by del hmax = μ²R,…

A: Given:∆hmax=μ2 RR= radius of the roll,μ= coefficient of frictionμ=0.1

Q: Maximum reduction in thickness for one pass in rolling process is Ahmax that can be expressed by Ah…

Q: A W310 x 52 beam is made with a material that has a maximum shearing stress of 90MPa. Determine the…

A: As Given in Question:- Shearing Force = 90 Mpa W310*52 depth from table = 318 mm Area for this =…

Q: A hole with a diameter of 18 mm will be drilled in a sheet material with a thickness of 4 mm.…

A: D = 18 mm t = 4 mm Stress = 640 MPa Shear force (F) = ?

Q: P Find the smallest diameter bolt that can be used in the clevis in Fig. if P = 435 kN. The shearing…

Q: Question # 4 A cup of height h=30 mm and diameter d = 50 mm is to be drawn from a steel sheet of 2 m…

Q: Example 11.18. A rod of circular section is subjected to a shearing force on a plane perpendicular…

Q: d the shear and am shown in fig

Q: A circular shape blank will be cut of 100 mm diameter from a strip of 2.8 mm with a clearance value…

A: Given data as per questiondiameter of blank =100 mmstrip thickness=2.8 mmclearance value=0.25…

Q: In Figure 4.1, assume that a 21 mm diameter rivet joins the plates that are each 110 mm wide. The…

Q: What is the difference between a single shear and double shear

A: Shear strength is defined as the greatest load that can be supported before a fastener…

Q: A metal cutter is used to chop metal sheets. The length of the metal sheets is 100 width of the…

Q: Problem: Use the elasticity theory to determine the maximum shearing stress, the angle of twist per…

A: Elasticity theory is concerned with the connection between forces applied to an item and the…

Q: A plate is fastened to a fixed member by four 20-mm-diameter rivets arranged as shown in Fig. P-333.…

A: Given data Diameter of rivets = 20 mm Force = 14 kN

Concept explainers

Torsion

In mechanical engineering, torque, torsion, and twisting moment are three of the most important concepts which have different meanings. Torque is the consequence of a moment of a force that produces an angular acceleration in a body or induces rotational kinetic energy in a body. For instance, in an automobile, the power transmission shaft is a body that is always under rotation due to the external torque acting on it, this torque is created by the engine.

Question

What is the area of the tube? What is the total length of the median line? The shearing stress value will be. The angle of twist result is.

An aluminum tube with the cross section
shown has a constant wall thickness of 2
mm. A torque T = 400 N-m is applied to
%D
the tube. Use G= 28 GPa *
40 mm
10 mm
40 mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Solve the preceding problem if the internal pressure is 3,85 MPa, the diameter is 20 m, the yield stress is 590 MPa, and the factor of safety is 3.0. (a) Determine the required thickness to the nearest millimeter. (b) If the tank wall thickness is 85 mm, what is the maximum permissible internal pressure?
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
A copper alloy pipe with a yield stress aY= 290 MPa. is to carry an axial tensile load P = 1500 kN (see figure part a). Use a factor of safety of 1.8 against yielding. (a) If the thickness t of the pipe is one-eighth of its outer diameter, what is the minimum required outer diameter dmin? (b) Repeat part (a) if the tube has a hole of diameter dt 10 drilled through the entire tube, as shown in the figure part b.
The one end of a hollow square tube whose side is 10.47 in with 1.47 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using (a double-pin) system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ(allowable) = 243 ksi for pin material.
The one end of a hollow square bar whose side is 10.42 in with 1.42 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a pin. Find the minimum diameter of pin is used. Take oall = 243 ksi for pin material.
9:0. محو التحدید blä 10 FIND STRESS IN Aluminum. IF E st= .200000 MPa, Ealu.=7000O MPa 100 kN RALU.=30 MM Aluminum Steel no one 69 MPa 31 MPa 19 MPa 55 MPa bläi 10 find the shear stress in bolt in pin A 60 kN 1m RST = 20 MM
N N The one end of a hollow square bar whose side is (10 +) in with (1 +) in thickness is under 100, a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and oau = 243 ksi for pin material. N= 47,
The one end of a hollow square bar whose side is 10.47 in with 1.47 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and Oallowable = 243 ksi for pin material.
The one end of a hollow square bar whose side is 10.17 in with 1.17 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ allowable= 243 ksi for pin material.
Find the size of 14 bolts required for a CI engine cylinder head. The diameter of the cylinder is 400mm and the steam pressure is 0.12N/mne.Take the permissible tensile stress as 35MPa.
Find the size of 14 bolts required for a C.I. steam engine cylinder head. The diameter of the cylinder is 400 mm and the steam pressure is 0.12 N/mm2 . Take the permissible tensile stress as 35 MPa.