Answered: What is the ratio of the maximum to…

Engineering

Civil Engineering

What is the ratio of the maximum to nominal shear stress for the beam described in Question 7?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The bar is subjected to the axial load. There is a shaded section which is oriented at 8 from the…

Q: Two square bars are welded together and loaded axi- ally as shown. Determine the maximum normal…

A: Given Data: The size of bar AC is w1=40 mm. The size of bar CD is w2=50 mm. The load P1=130 kN. The…

Q: Compute the corresponding shear stresses.

Q: 17 MPa 27 MPa 56 MPa

Q: A timber beam 98 mm wide by 160 mm high is subjected to a vertical shear V = 29 kN. Determine the…

A: Draw the diagram as follows.

Q: 7. The rectangular beam shown has an allowable stress of 735 psi and an allowable shear stress of…

Q: The rectangular cross-section is 500 mm wide and 900 mm deep. Calculate the maximum shear stress in…

A: Find reactions:∑ MA=0RB3-21.50.8-15.82.1=0RB=16.8kN∑ Fy=0 R+RB-21.5-15.8=0 RA=20.5kN Max shear…

Q: Calculate the allowable nominal beam shear stress in MPa. Express your answer in 3 decimal places.

Q: Two wooden planks 50 mm x 150 mm are built-up into an upright T-section. The said built-up is to be…

Q: A simply supported beam 4 meters long has a cross-section below. Determine the maximum uniformly…

A: ASKED: To determine the maximum value of the uniformly distributed load w for given allowable…

Q: A torque of T = 5000 kN·m is applied to a torsion member whose cross section is shown. Dimensions…

Q: if the maximum shear stress acting on rectangular beam is 50 N/mm, determine the average shear…

Q: ra minor principle stress of 50 kPa, what is the maximum value possible for the major prino e…

Q: A bar having a radius equal to 0.375 inches is subjected to different torques along its span as…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

Q: 150 kN/m2 45kN/m2 B 45KN/m2 to 195 kN/m2 65° A to

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: What is Maximum in-plane shear stress?

A: The Maximum in-plane shear stress is explained as below, The maximum shear stress of the plane that…

Q: What is the Maximum In-Plane Shear Strain?

A: The Maximum in-plane shear stress is explained as below, The maximum shear stress of the plane that…

Q: For the structure below, assume that a = 60 in., b = 90 in., c = 40 in., and d = 50 in. Determine…

A: The given structure is analyzed by using the equation of equilibrium forces. The sum of all forces…

Q: AW310 x 38.7 standard steel shape is used to support the loads shown on the beam in the figure.…

Q: An I-section beam shown is subjected to a shear force of 50 kN. Find the magnitude and position of…

A: Maximum shear stress: It is defined as the maximum shear stress which occurs at a small portion of…

Q: What is the max shear stress in the shaft? Input your answer as a value only in MPa to one decimal…

Q: A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded. For bronze, G…

Q: A cast iron link is 50mm wide by 250mm high by 550 mm long. The allowable stress in tension is 50…

Q: Determine the largest axial load P that can be safely supported by a flat steel bar consisting of…

Q: calculate the magnitude of the maximum compressive bending stress (in psi)

Q: Given the beam shown with computed reactions and a cross section. Determine the maximum…

A: We will find both positive and negative moment and then determine the compressive stress at top and…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

Q: A simply-supported beam is subjected to a loading resulting in the bending moment diagram shown. The…

A: The maximum bending stress is given by: σc max=M×yI M = Maximum compressive bending moment y =…

Q: The prestress T-beam section has a simple span of 6 m. The tendons is subjected to an initial stress…

Q: An 8 m simple beam is loaded with a 208 kN point load at the first third of its length. The cross…

Q: What is the shearing stress developed at the neutral axis of the beam with a circular cross section…

Q: What is the minimum diameter of a bar subjected to an axial load of 6.5 kN if its ultimate stress is…

A: Given:- Axial load, P=6.5 KNUltimate stress, σ=140 MPa To find:- Minimum diameter of bar

Q: A bar having a cross-sectional area of 700 mm² is subjected to axial loads at the positions…

Q: The beam shown has a rectangular cross section 4 in. wide and 8 in. deep. Determine the maximum…

A: Given data : Depth (D)=8 inWidth (B)=4 in

Q: Describe about the Total Stress Method.

A: At any given plane section in the soil mass total stress is defined as the sum of the self weight of…

Q: QUESTION 3. A T-beam having the cross section shown projects 2 m from a wall as a cantilever beam…

A: Maximum moment on the beam :Mmax=-6×222=-12kN-m

Q: largest uniformly distributed load that can be applied over the right two-thirds of the beam if the…

A: ΣMR1=0 3R2=2w(2) R2=4/3w ΣMR2=0 3R1=2w(1) R1=2/3w (fb)max = Mc/I Where, (fb)max = 60MPa…

Q: A rectangular concrete beam 250 mm wide and 600 mm deep is pre-stressed by means of 16 high tensile…

Q: An axial load P is supported by a short steel column, which has a cross-sectional area of 10500 mm2.…

A: ASKED: To determine the minimum required dimension of the base plate. Given, Cross-sectional area…

Q: Find the maximum shear stress in the beams and cross-sections

A: Given-A beam W12×55 carrying loading system. Required- to find maximum shear stress in the cross…

Q: Determine the absolute maximum shear stress for each of the following plane stress states for which…

Q: 1What is the value of shear at B? 2At what distance from A is zero shear located? 3What is the…

Q: Compute the maximum shear stress

Q: 1.61.The state of stress at a point relative to an x, y, z coordinate system is given by 12 4 4 -8…

A: Answetr given in the below attachment

Q: a vertical cylindrical steel tank is 3m in diameter and 6m tall, the walls of the tank have…

Q: For the given beam section, determine the thickness of the point where the maximum horizontal shear…

A: The given beam section is as follows:

Concept explainers

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with. 

Question

A thin beam with a solid rectangular cross-section is loaded as shown in Figure Q7 below.
W
W
L/3
L/3
L/3
Figure Q7
What is the ratio of the maximum to nominal shear stress for the beam described in Question 7?
O a. 3:2
O b. 1:4
Ос. 3:1
O d.2:1
O e. 1:2
O f. None of the provided answers are correct.
O 8. 1:1

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

2max 1 max A beam comprises of two metals (1 and 2). Both the metals are in contact as shown in figure. If a moment M, is applied, what is the value of 0₁/0... It is given that both the metals will bend separately about their own neutral axis. Also draw bending strain and bending stress diagram. Mo Mo at th Jicc E₁, I, E2, 12 d₁ d₂
Q1/ The 15-mm diameter steel bolt is screwed tightly into a block at A. Suppose that the couple forces F causes the ends of the wrench to be displaced 3 mm, determine the maximum shear stress in the bolt. Assume that the wrench is rigid and modulus of rigidity of steel is 75 GPa. 150 mm i50 mm mni
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The figure (all dimension are in mm) below shows an I-section of the beam. The shear stress at point P (very close to the bottom of the flange) is 12 MPa. The stress at point Q In the web (very close to the flange) is: N'-. 100- P Q 201 100- T 20 81484 80 20 40 --N (a) Indeterminable due to incomplete data (6) 60 MPa (c) 18 MPa (d) 12 MPa 068
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
20MPA a In Figure , according to the stress condition of a stack of I-section beam. (30Mpa is the shear stress value.) 30MPA I- 40MPа 1-)Calculate the principal stresses, location and angle. A 2-)Calculate the stress components that will affect the plane in a section a-a that makes a 300 angle shown in the figure.
Q2: Find the permissible distance (X) for the beam shown in figure. If the stresses in tension is 40 MPa and in compresion is 80 MPa. 4kN 4KN. 220 16KN N. A 大 6m 'RB INA: 4 = 20* (o mm
Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 GPa. A L1 Dia. 1 + B B P1 L2 Dia. 2 P2 L3 30 mm o P3 Dia. 1 Dia. 2 P1 P2 P3 L1 L2 L3 (mm) (mm) (kN) (kN) (kN) (mm) (mm) (mm) 60 45 105 25 1350 2150 1350 40
Q4 (b) Figure Q4(a) shows a steel beam with length of 4 m that is supported by a steel column at point B. The steel column of AB has a rectangular cross section (40 mm× 70 mm). The ends are assumed to be pin connected. The yield stress of steel is o y 250 MPa. The Modulus Elasticity of the steel is 200 GPa. Use factor of safety of 1.5. (i) Check whether the Euler's equation is appropriate or not. (ii) Determine the maximum distributed load (W) that can be applied to the beam so that the column of AB does not buckle.
Q4 - For the given beam and cross section, at point B on section A-A (mid-span), determine the followings and show them on a differential element. a) Principal stresses and its orientation b) Maximum in-plane shear stress and its orientation t 7 kN/m 2 m A - -2 m FATT 5 mm 5 mm 50 mm B t 5 mm → *F 3 mm Section A-A 80 mm
A beam cross section is shown. If the beam is subjected to a moment of 400N.m, the maximum bending stress will be? I, = 200 mm 4 8 mm 4 mm O a. 16GPA О Б. 10GPa 12GPA O d. 8GPA
J- A distributed load op w (kulm) is applied over the entire tength OF a simply supported beam Gm long . The beam section is as shown. Determine the maximum value OF w iF Of Ś 1OMP , and yE 800KP. 80 mm X 200 mm 360mm 200mm