When crude oil (r.d = 0.855, µ = 71.8*104 Pa. s) flows in a 50 mm horizontal pipeline at 4.5 m/s, a pressure drops of 6500 kPa occurs in 60 m of pipe. Calculate the pressure drop in the corresponding length of a pipe model 25 mmd when gasoline (r.d = 0.68, µ = 2.9*104 Pa. s) flows in the model for complete similarity between model and prototype. %3D

When crude oil (r.d = 0.855, µ = 71.8104 Pa. s) flows in a 50 mm horizontal pipeline at 4.5 m/s, a pressure drops of 6500 kPa occurs in 60 m of pipe. Calculate the pressure drop in the corresponding length of a pipe model 25 mmd when gasoline (r.d = 0.68, µ = 2.9104 Pa. s) flows in the model for complete similarity between model and prototype. %3D

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is flowing at 0.075 cu.m./sec through a glazed porcelain pipe 400m long and 200mm diameter. The pipe roughness is 0.0015mm. Properties of water: Density: 1,000 g/cu.m., viscosity = 0.001 N-m/sec. What is the velocity of water in the pipe? What is the Reynold's number? Steady State flow exists in pipe that undergoes a gradual expansion from a diameter of 6in. Assuming constant density and the inlet flow velocity is 22.4 ft/sec. What is the size of the exit pipe if the exist flow velocity is 12.6 ft/sec?
Q5/ Oil flows in a 0.3 (m) diameter pipe with a flow velocity of 2.7 (m/s). The physical properties of Oil are: 1- Dynamic viscosity is 0.39 (N.s/m²). 2- Density, p = 950 (kg/m³). Find: 1- The value of Reynold's Number Re and Mention the Type of flow. 2- The value of coefficient of friction f of the pipe. ---- ----- --
A venturi meter, shown in Fig. designed constriction whose pressure difference is a mea- sure of the flow rate in a pipe. Using Bernoulli's equation for steady incompressible flow with no losses, show that the flow rate Q is related to the manometer reading h by is a carefully 2gh(PM – p). A2 VT- (D/D;)4 where py is the density of the manometer fluid. 2
Q.5 a) In a 80 mm diameter pipeline an oil of specific gravity 0-8 is flowing at the rate of 0-0125 m^3/s. A sudden expansion takes place into a second pipeline of such diameter that maximum pressure rise is obtained. Find :(i) Loss of energy in sudden expansion,(ii) Differential gauge length indicated by an oil-mercury manometer connected between the two pipes. (iii) find the maximum pressure rise. (-
1. A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm, and stroke L-5 mm. The fluid density is p = 800 kg/m³ and the viscosity is μ = 0.5 Pa-s. The pressure to drive the flow is p=6.25 Pa. a. How many non-dimensional groupings can be obtained? Derive them. b. If the flow transitions at Re = PV(2R) =2300. Is the generated flow laminar or turbulent given Q=20 mL/s? LL c. Assume the pressure gradient is uniform on the cross-section and can be calculated using OP=-. The velocity profile in the cylinder is u(r) = ax - [1-(²]. Sketch the velocity profile. Calculate the shear stress at the R² ap 2UÔI cylinder wall and label the direction. d. Calculate the flow rate Q with the velocity profile in (c).. e. If the shear stress is uniform over the cross-section, i.e. T = C, what's the pressure gradient distribution and sketch it? L L. R
A thin-plate orifice is used to measure water flow rate. The water temperature is 27 C and a mass flow rate of 50 lit/s is measured by the orifice. The pipe diameter is 26 cm and the orifice diameter is 7 cm. Find the non-rcoverable pressure drop. [Ans.: 21 m, Cd = 0.6, K = 2.5].
Assume the following standard values if not provided with the problem statement • Air o p = 1.2 kg/m³ μ = 1.8 x 10-5 kg/(m s) • Water o p = 1000 kg/m³ o μ = 0.001 kg/(m s)
1. A piston-cylinder is producing a viscous oil flow, which has the flow rate of Q, radius R=1.5 mm, and stroke L-5 mm. The fluid density is p = 800 kg/m³ and the viscosity is μ = 0.5 Pa-s. The pressure to drive the flow is p-6.25 Pa. a. How many non-dimensional groupings can be obtained? Derive them. b. If the flow transitions at Re = V(2R) =2300. Is the generated flow laminar or turbulent given Q=20 mL/s? c. Assume the pressure gradient is uniform on the cross-section and can be calculated using - The velocity profile in the cylinder is u(r) = [1-2²]. Sketch the velocity profile. Calculate the shear stress at the ax 2μ δχ cylinder wall and label the direction. d. Calculate the flow rate Q with the velocity profile in (c).. e. If the shear stress is uniform over the cross-section, i.e. T = C, what's the pressure gradient distribution and sketch it? L r L. R
Three pipes A, B, and C are interconnected as shown in figure 1. The pipe dimensions are as follows: Pipeline D(cm) L (m) ƒA 15 300 0.01B 10 240 0.01C 20 600 0.005 Find the rate at which water will flow in each pipe, ignoring the shock losses at P and entry to pipelines A and B.
Q3/ Water is flowing upwards in an inclined homogeneous pipe from point No. (1) to point No. (2). The following data is available:- 1- Length of pipe, L= 1400 (m). 2- Diameter of pipe, d= 0.25 (m). 3- Elevation of point No. (1) is 15 (m) above the Reference line and elevation of point No. (2) is 30 (m) above the Reference line. 4- Piezometric head at point No. (1), hi= 61.16 ( m of water height). 5- Piezometric head at point No. (2), h2= 20.39 (m of water height). 6- Friction coefficient f=0.02 and hL=zero Find: 1- Head loss of water flow in the pipe from point No.(1) to point No.(2) due to friction hf. 2- Water flow rate Q and flow velocity v in the pipe. Draw the H.G.L. of water flow in the pipe from point No. (1) to point No. (2).
An oil having viscosity 0.08 N S/m², Specific weight 8829 N/m, density 900 kg/m flow at the rate of 5410 m/sec through a horizontal circular pipe of 0.12 m diameter and length 150 m. Find, (a) Pressure difference in 150 m length in kN/m² (b)Wall shear stress in N/m² (c) Average, and maximum velocity.
A 9.8 m A fluid of relative density 0.88 is flowing through a pipe constant diameter of 15 mm (see the Figure). The pressure at A is 150 kPa and the pressure at B is 225 kPa. The elevation between points A and B is 9.8 m. Calculate the friction loss of the fluid (in meters), (provide your answer with four decimal points) P Type here to search O 10°C Sunny AQA ENG 0029 16/02/2022 DELL priSc FS F6 5 E R J K L %23 F E Aock C V sage page VO at gr ctri