With matlab M-file instructions,1- Write the T.F of the system below2- Draw the bode diagram.3- Write an M-file command to find: Gain Margin, Phase Margin, Gain cross overfrequency (wg) and Phase cross over frequency (wp)4- How to check the stability of the system?T.F=100s3+2s26s+3

process information from images. However, based on your description, it appears you're looking to…

Answered: With matlab M-file instructions, 1-…

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter24: Resistive-inductive-capacitive Parallel Circuits

Section: Chapter Questions

Problem 4RQ: A tank circuit contains a capacitor and an inductor that produce 30 of reactance at the resonant...

See similar textbooks

Similar questions

HW: Determine Zin, Zo and the small-signal voltage gain. P type C₁ C₂ Vo D Vin Rs RD RL SINT 4k 2k 4k Zin -5V Zo +5V = kp 1mA/V2 Vr = -0.8V λ=0 Bobin painleido XL=SL = jwL Frequency Response Sm= 2 kp (VSG₂Q +VT) rd = 1 A IDQ ID= kp (VSC₂+V+) ² notion Xc = Copacite 1 (WC 345
Eill in the blank with corect answers B Frequency Series Resonance - Impedance vs. Frequency. The graph of impedance against frequency for an RLC series resonance circuit is shown in the picture. At which point the current will be maximum At point A At point C At point B At point D The inner most layer of an optical fhotI Is cantu Impedance
A parallel R-L-C circuit is fed by a constant current source of variable frequency. The circuit resonates at 100 kHz and the Q-factor measured at this frequency is 5. Find the frequencies at which the amplitude of the voltage across the circuit falls to (a) 70.7% (b) 50% of the resonant frequency amplitude.
The below 4 figures are the angle of the transfer function of passive filters. Phase (deg) -45- Phase (deg) (Cep) sid 45 10 10 Frequency (radisec) 10² Frequency (rad/sec) Figure-1 shows the frequency response of Figure-2 shows the frequency response of Figure-3 shows the frequency response of Figure-4 shows the frequency response of 4) ( + 4 10 10" 10
We will use magnitude comparator and a Quad 2-to-1 MUX. How ?
30. Realize the imego phase fiteo with tue impulse desponse - hon) = son) + Scn-+) - son2) + scna)+SCny) %3D
H.W: A resistor of resistance R=1000 2is maintained at 17 °C and it shunted by 100 uH inductor. Determine the ms noise voltage across the inductor over a frequency bandwi dth of: Ans: 182 x10° volt Ans: 9.22 x10 volt Ans: 2.34 x10 volt i) 15.9 kHz ii) i) 159 kHz 1590 kHz
Calculate the resonant frequency of the median resonator. The value of D2= 6.05 cm, D1= 1.72 cm,Lreal= 1.89 cm and the temperature is 25°. Also obtain the value in units of the frequency ofresonance.
QUESTION 3 (a) Figure Q3(a) shows an approximate and actual Bode Plot for magnitude and phase. From the given Bode Plot, extract all the information that you might think valuable to the user as a control engineer. You can choose either to use the approximate Bode Plot or actual Bode Plot in this analysis. Magnitude Plot 40 Approimate -Actual 20 -80 -100 To Freg rad's) Phase Plot Approainate -100 Actual -120 -140 6-160 E -200 -220 - -240 -260 Freg radis) Figure Q3(a)
4. A general fiter ciocurt is shoun in tne figuse. If R,=Rz=RA and Rg = Ry = RB, then find the transfer function and identify the ciocuit. Re Vo Rg Ry
How & Find the transfer function, Center frequency, and bandwidth in figure. what type of filter?, Q, H(jWo), H(jo), H(jas) How:- repeat the previous H-W in the figure below. R 7 Vi + REVO RL
1- Consider the following Bode plot of a plant: Amplitude [dB] Phase [°] 20 10 -10 -20 -30 10-1 -90 -120 -150 -180 10-1 10⁰ 10⁰ Frequency [rad/s] -Bode plot 10¹ 10¹ Use the bode plot shown above to determine the approximate Gain crossover frequency wc, phase margin, and gain margin.

SEE MORE QUESTIONS

Recommended textbooks for you

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

With matlab M-file instructions, 1- Write the T.F of the system below 2- Draw the bode diagram. 3- Write an M-file command to find: Gain Margin, Phase Margin, Gain cross over frequency (wg) and Phase cross over frequency (wp) 4- How to check the stability of the system? T.F= 100 s3+2s26s+3